Summary of the content on the page No. 1
Installation Manual
For Service Engineer
Pick an installation spot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Attaching the 2nd paper cassette . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Joining Scanner unit and Printer unit . . . . . . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 2
Summary of the content on the page No. 3
1 2 3 4 5 Installation Setting up Pick an installation spot Unpacking Where should you install your fax machine? The location should be: • Clean — Dust buildup can damage your machine. (However, do not use a cover!) In the open — Allow at least 12 inches (30 cm) of clearance around your machine. Be sure that you never cover the machine. Its vents must be able to “breathe.” Main unit (Scanner unit) Main unit (Printer unit) 2nd paper cassette Bypass tray Away from direct sunlight — This helps
Summary of the content on the page No. 4
Installation Installation Peel off the all tapes and cushions from the machine. Attaching the 2nd paper cassette Multi purpose cassette Unpacking Cushion Remove the paper cassette from the box and check that the following acces- 1 sories are contained in the box. (1) Fixing plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Tapes (2) Flat-head screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 5
Installation Installing 2nd paper cassette Attach the bracket with care wedg- 6 ing the harness connected. Note: Push the harness into a Grasp the front and rear handles 1 recess in the rear as illus- of the machine and set it on the trated to ensure easy and paper cassette. proper installation of the bracket. Note: Make sure that the tabs on the base plate of the paper cassette fit into the slits in the bottom of the bracket. Pull out the multipurpose cassette Accessing through the hole in the
Summary of the content on the page No. 6
Installation Joining Scanner unit and Printer unit Fix the scanner unit and the printer 4 Important: Be sure that you do not turn the power on until after you have unit with two fixing screws. removed the transport screws (in step 5). Otherwise, damage could result. Remove one screw, then remove the con- 1 nect cover. Remove two transport screws by turn- 5 ing them 90º. Attach protection sponges on each transport screw hole. Put the scanner unit on the printer unit. 2 Set the pins on the printer
Summary of the content on the page No. 7
Installation Installing the printing supplies Pull up the printer cover release and 3 This machine prints incoming faxes and copies with a laser print engine. The engine open the printer cover. requires two types of printing supplies (sometimes also called consumables): The drum cartridge — It yields 74,000 normal letter- or A4-sized printouts. By “normal,” we’re referring to the amount of text and/or graphics on each page. This is based on an industry-standard test document. The toner bottl
Summary of the content on the page No. 8
Installation Grasp the handles and push the drum Sharply tap the new toner bottle against a 6 2 cartridge into the machine until it clicks. desk or other hard surface four or five times. Then turn the toner bottle upside down and tap it the same way again. Close the printer cover. Shake the new toner bottle well and turn 7 3 it over lengthwise five times. With the seal on the toner bottle facing up, 4 slowly peel off the seal as shown at right: Note: Be careful, some toner may puff Installing th
Summary of the content on the page No. 9
Installation Plug in and power up Turn off the transport mode Important: Be sure you do not turn the power on until after you remove the Plug one end of the telephone line cord into the LINE jack on the machine’s transport screws. (See step 5 on page 4.) 1 rear side. Plug the other end of the cord into a standard telephone wall jack, To turn off the transport mode: just as you would plug in a phone. Plug the non-pronged end of the AC power cord into the AC power cord jack 2 on the rear side of t
Summary of the content on the page No. 10
Installation Loading paper Paper size and type input After you attach a new paper cassette or change the paper size, you must tell the machine the new setting. Pull the cassette toward you. 1 Paper size and type input for 1st cassette Push down the bottom plate inside 2 the cassette so it clicks and the plate Press COPY to change to the copy mode. and the bottom of the cassette are 1 even. Press NEXT, then press [Chg.Ppr.]. 2 Use the cursor key to select the 1st cassette. 3 Then press [Enter]. W
Summary of the content on the page No. 11
Installation Select the paper size to be set. 2 When using special sized paper: When using the standard paper size: (1) Press [Other]. (1) Select the paper size using the cursor key or pressing [Paper]. (2) Select “Custom” using the cursor key. (2) Press [Enter]. Note: You can register three types of special size as you want. (3) Press [Enter]. (4) Enter the horizontal and vertical size of the paper using the numeric keypad. Note: You can also enter the paper size using and of the cursor ke
Summary of the content on the page No. 12
Installation Initial setting Press [Enter] to save the clock setting and continue the settings. 4 If you are setting up the North American version machine, proceed to next step. Otherwise, skip to step 8. Clearing stored settings Before initial setting, clear your machine’s built-in user data memory. This ensures the memory will hold only your settings. The LCD now asks if you want to set the calen- 5 Important: After you done the initial setting, do not clear the memory again dar/clock to a
Summary of the content on the page No. 13
Installation The LCD now asks you to enter the name you 14 want to appear at the top of faxes you send. The name may be up to 22 characters in length. Select TTI 1, 2 or 3 using the cursor key. Then press [Enter]. Use the one-touch keys to enter letters and other non-numeric characters. To 15 enter characters, see page 1.15 in the operating instructions. Note: If you make a mistake, press [Clear] to erase to the left. To change just one character in the name, move the cursor by cursor key. Press
Summary of the content on the page No. 14
Installation Changing paper size of the 2nd paper cassette Note: There are two springs under the paper The initial setting is as follows. lifting plate. North American Version : Letter Note: The replacement springs are stored in European Version : A4 the bottom of the front side of the paper cassette. While pressing the stops in the direction of the arrows as shown in the figure, Note: Always set the springs so the upper end 1 pull out the tray of the paper cassette. of the spring fits into the
Summary of the content on the page No. 15
Summary of the content on the page No. 16
D84-90510-60
Summary of the content on the page No. 17
Getting started EasyStart (Initial setting) EasyStart software is already installed on your Muratec machine. It guides you Getting started through the process of entering your machine’s settings. Determine the following before you go any further: Remember that the settings you make here can always be changed later. The type of dialing your telephone system requires — Choose either tone or 1 pulse (rotary) dialing. Clearing stored settings The name and fax number you want to appear on your faxes
Summary of the content on the page No. 18
Getting started Press [Enter] to save the clock setting and continue EasyStart. 4 The LCD now asks you to enter the name you 14 want to appear at the top of faxes you send. The LCD now asks if you want to set the calen- The name may be up to 22 characters in length. 5 dar/clock to automatically Select TTI 1, 2 or 3 using the cursor key. Then recognize daylight saving time (DST). press [Enter]. When the setting is On, your machine automati- Use the one-touch keys to enter letters and 15 cally
Summary of the content on the page No. 19
Getting started How to set the document Acceptable document size How to set the document The acceptable dimensions as follows: Setting the documents in the Automatic Document Feeder In the Automatic Document Feeder(ADF) On the Flatbed Scanner(FBS) glass Set your document face up into the docu- 1 ment feeder. Your machine’s ADF will hold up to 50 sheets. Note: The green arrow will appear on the ADF cover when the document is set. Feed direction Adjust the document guide to fit your 2 document
Summary of the content on the page No. 20
Basic copy features Some guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.1 Basic procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4 Reduce / Enlarge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.5 Sorting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
