Summary of the content on the page No. 1
Owner’s Instructions
SPP4251
Summary of the content on the page No. 2
Important Warranty Information Regarding Television Format Viewing Wide screen format PDP Displays (16:9,the aspect ratio of the screen width to height) are primarily designed to view wide screen format full-motion video. The images displayed on them should primarily be in the wide screen 16:9 ratio format,or expanded to fill the screen if your model offers this feature and the images are constantly moving. Displaying stationary graphics and images on screen, such as the dark side-bars on nonexp
Summary of the content on the page No. 3
Table of Contents General Information Channel Control Your New Plasma Display Panel ......................6 Fine Tuning Channels ..................................64 Remote Control Buttons ..................................8 LNA (Low Noise Amplifier) ..........................65 Wall Installation Instructions ..........................10 How to assemble the Stand-Base ..................14 Connecting a PC and Operation Connecting a PC ........................................68 Connections Adjusti
Summary of the content on the page No. 4
PLASMA DISPLA Y P ANEL General Information Your New Plasma Display Panel ......................................................6 Remote Control Buttons ..................................................................8 Wall Installation Instructions ..........................................................10 How to assemble the Stand-Base ....................................................14
Summary of the content on the page No. 5
Your New Plasma Display Panel Front Panel Speakers Remote Control Signal Receiver Aim the remote control towards this spot on the PDP. SOURCE button I/ Press to display all of the available video sources Press to turn the PDP on and off. (TV, AV1, AV2, AV3, S-VIDEO1, S-VIDEO2, COMPONENT1, COMPONENT2, PC, DVI). Power Indicator - Power Off: Blue MENU button Displays the main on-screen menu. - Power On: Off VOL(+,-) button Press to increase or decrease the volume. Also used to select or adjust ite
Summary of the content on the page No. 6
Side of the TV S-Video Input Video Input Audio Input (L, R) Rear Panel ŒDVI INPUT (DVI-D / L-AUDIO-R) ØAV1, AV2, AV3 Connect to the digital video and audio (VIDEO / L-AUDIO-R ) output jack for device with DVI output. Video and audio inputs for external devices, such as a camcorder or VCR. ´MONITOR OUT (VIDEO / L-AUDIO-R) Outputs for external devices ∏COMPONENT1, COMPONENT2 Video (Y/Pb/Pr) and audio (L-AUDIO-R) ˇPC INPUT (RGB IN / AUDIO) inputs for Component. Connect to the video and audio o
Summary of the content on the page No. 7
Remote Control Buttons Remote Control ŒPOWER button Turns the PDP on and off. ´ASPECT button Press to change the screen size. ˇNumber buttons ¨+100 button Press to select channels over 100. For example, to select channel 121, press “+100”, then press “2” and “1.” ˆMUTE button Press to mute the PDP sound. ØVOL (Volume) buttons Use it to adjust volume. ∏SLEEP button Press to select a preset time interval for automatic shutoff. ”MENU button Displays the main on-screen menu. ’ENTER button Confirms a
Summary of the content on the page No. 8
¸SRS TSXT button Selects Trusurround XT mode. ˛ MTS button Press to choose stereo, mono or Separate Audio Pro- gram (SAP broadcast). ◊AUTO PROG. button The TV automatically cycles through all of the avail- able channels and stores them in memory. ±ADD/DEL button Press to add or delete channels in the TV’s memory. ≠DNIe button Activates DNIe (Digital Natural Image engine). –CAPTION button Controls the caption decoder. —SET button Used during set up of this Samsung remote control, so that it wil
Summary of the content on the page No. 9
Wall Installation Instructions Installation Notes Do not install the PDP on any location other than a vertical wall. 1 To protect the performance of the PDP and prevent problems, avoid the following locations: 2 • Do not install next to smoke and fire detectors. • Do not install in an area subjected to vibration or high voltage. • Do not install near or around any heating apparatus. Use only recommended parts and components. 3 ➤ This wall mount bracket installation guide is for the following
Summary of the content on the page No. 10
Fixing the PDP panel to the wall attachment panel bracket Remove the screws from the back of the PDP. 1 Connect insulation holders to screws (see the illustration below). 2 • If you are uncertain about installation, hire a specialist to install the wall mount bracket. • Be sure to check that the insulation holders are completely secured on both the left and right side after hanging the PDP on the wall mount bracket. • Be careful to avoid getting your fingers caught during installation. • Make
Summary of the content on the page No. 11
Put the 4 insulation holders on the PDP in the grooves of the wall mount bracket and pull down on the PDP (Œ) to secure it to the wall mount bracket (´). Tighten the 4 screws as shown (ˇ) so that the PDP cannot be separated from wall mount bracket. PDP panel Wall Wall attachment panel bracket Connecting External Devices to the PDP To connect external devices such as a DVD or a Home Theater System to the PDP, please refer to following instructions: Be sure to remove the safety pins underneath t
Summary of the content on the page No. 12
How to Adjust Mounting Angle Factory default The wall mount bracket is delivered separately. Please tighten the captive screw in the direction of the arrow after assembling the bracket. Changing the angle Secure the PDP to the wall mount bracket. (Please refer to the following 1 instructions.) Set the angle by pulling the upper end of the PDP attached to bracket in the direction 2 of the arrow. The angle can be adjusted from 0° to 15° by ±2°. 3 13
Summary of the content on the page No. 13
How to assemble the Stand-Base Assemble two support pins with the stand base and firmly secure both sides of the support pins using 8 screws provided. 1 Assemble the PDP with the stand and firmly secure the PDP using 4 screws provided. 2 Two or more people should carry the PDP. Never lay the PDP on the floor because of possible damage ➤➤ to the screen. Always store the PDP upright. 14
Summary of the content on the page No. 14
PLASMA DISPLA Y P ANEL Connections Connecting VHF and UHF Antennas ..............................................16 Connecting Cable TV....................................................................17 Connecting a VCR........................................................................19 Connecting a Camcorder ..............................................................20 Connecting a DVD Player..............................................................21 Connecting a DTV Receiver .
Summary of the content on the page No. 15
Connecting VHF and UHF Antennas Antennas with 75-ohm Round Leads If your antenna looks like this: it has 75-ohm round leads. Plug the antenna lead into the VHF/UHF terminal on the PDP. 1 Use the Antenna Cable, an accessory included in the product package. 16
Summary of the content on the page No. 16
Connecting Cable TV You can connect different cable systems to your PDP, including cable without a cable box, and cable with a cable box that descrambles some or all channels. Cable without a Cable Box Plug the incoming cable into the VHF/UHF terminal on the PDP. 1 Use the Antenna Cable, an accessory included in the product package. Cable with a Cable Box that Descrambles All Channels. Find the cable connected to the ANTENNA OUT terminal on your cable box. This terminal might be 1 labeled
Summary of the content on the page No. 17
Cable with a Cable Box that Descrambles Some (But Not All) Channels To complete this connection you will need a two-way splitter, an RF (A/B) switch, and four coaxial cables (which you can buy from your Samsung dealer or any electronics store). Find and disconnect the cable that is con- nected to the ANTENNA IN terminal of 1 your cable box. This terminal might be labeled "ANT IN", "VHF IN" or simply, "IN". Connect this cable to a two-way splitter. Connect a coaxial cable between an OUT- PUT
Summary of the content on the page No. 18
Connecting a VCR Connecting a VCR to the Video or S-Video/Audio jack PDP VCR Power Plug Audio Cable S-Video Cable Video Cable How to Connect Connect the Video/Audio cables between the AUDIO(L/R)/VIDEO jacks on the PDP and AUDIO/VIDEO OUT jacks on the VCR. (Note: For better video, you can use an S-Video cable.) Videotape Playback: 1. Turn on your PDP. 2. Press the TV/VIDEO button to select “Video” or “S-Video”. 3. Turn on your VCR, insert a videotape and press the play button. 19
Summary of the content on the page No. 19
Connecting a Camcorder Viewing camcorder tapes Camcorder PDP Power Plug Video Cable Audio Cable How to Connect Connect a Video/Audio cable between the AUDIO(L/R)/VIDEO jacks on the PDP and the VIDEO/AUDIO OUTPUT jacks on the camcorder. Viewing Tapes 1. Turn on your PDP. 2. Press the TV/VIDEO button to select “Video”. 3. Turn on your camcorder and set it to Video Mode. (For details, refer to your camcorder Owner’s instructions.) 4. Set the IN/OUT switch on your camcorder to OUT. 5. Insert the ta
Summary of the content on the page No. 20
Connecting a DVD Player (480i, 480p) This PDP displays the optimum picture in 720p mode. Playing DVD PDP DVD Player Power Plug Video Cable Audio Cable How to Connect b r Connect a Video Cable between the Y, P , P (COMPONENT1, 2) input jacks on the PDP 1 B R and Y/P /P output jacks on the DVD player. Connect a Audio Cable between the AUDIO L/R(COMPONENT1, 2) input jacks on the PDP 2 and the AUDIO OUT jacks on the DVD player. To Play DVD: 1. Turn on your PDP. 2. Press the TV/VIDEO button to selec
