Summary of the content on the page No. 1
SyncMaster 650MP-2, 650FP-2
LCD Display
User Manual
The color and the appearance may differ depend-
ing on the product, and the specifications are sub-
ject to change without prior notice to improve the
performance.
Summary of the content on the page No. 2
Safety Instructions Notational Note These safety instructions must be followed to ensure your safety and prevent property dam- age. Make sure to read the instructions carefully and use the product in the correct manner. Warning / Caution Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment. Note Important to read and under- Prohibited stand at all times Disconnect the plug from the Do not disassemble outlet Ground to prevent an electric Do n
Summary of the content on the page No. 3
Safety Instructions Ensure that the power plug is plugged into the power outlet firmly and correctly. • Otherwise, this may result in fire. Do not forcefully bend or pull the power plug and do not place any heavy material on it. • Otherwise, this may result in fire. Do not connect multiple appliances to the same power outlet. • Otherwise, this may cause fire due to overheating. Do not disconnect the power cord while using the product. • Otherwise, this may result in damage to the product due
Summary of the content on the page No. 4
Safety Instructions Keep heating appliances as far away from the power cord or the product as possible. • Otherwise, this may result in electric shock or fire. Do not install it in a badly ventilated location such as a bookcase or closet. • Otherwise, this may result in fire due to an increase in the in- ternal temperature. When putting the product down, make sure to put it down softly. • Otherwise, this may result in damage to the screen display. Do not place the front of the product on the
Summary of the content on the page No. 5
Connections Connecting a Computer There are several ways to connect the computer to the monitor. Choose one from the following options. Using the D-sub (Analog) connector on the video card. • Connect the D-sub to the 15-pin, [RGB IN] port on the back of your LCD Display and the 15 pin D-sub Port on the computer. Using the DVI (Digital) connector on the video card. • Connect the DVI Cable to the [DVI IN] port on the back of your LCD Display and the DVI port on the computer.
Summary of the content on the page No. 6
Safety Instructions When cleaning the product, make sure to disconnect the power cord. • Otherwise, it may result in electric shock or fire. When cleaning the product, disconnect the power cord and clean it with a soft, dry cloth. • (Do not use chemicals such as wax, benzene, alcohol, thinner, mosquito repellant, lubricant, or cleaner.) These may change the appearance of the product surface and peel off the indica- tion labels on the product. Since the product housing is easily scratched, make
Summary of the content on the page No. 7
Safety Instructions Do not try to move the monitor by pulling only the wire or the signal cable. • Otherwise, it may fall and result in electric shock, damage to the product or fire due to damage to the cable. Do not lift or move the product back and forwards or right and left while only holding the power cord or signal cables. • Otherwise, it may fall and result in electric shock, damage to the product or fire due to damage to the cable. Make sure that the ventilating opening is not blocked
Summary of the content on the page No. 8
Safety Instructions Take a rest for at least five (5) minutes after using the monitor for one (1) hour. This reduces eye fatigue. Do not install it in an unstable location such as an unstable rack or uneven surface or a location exposed to vibrations. • Otherwise, it may fall and cause personal injury and/or damage the product. • If you use the product in a location exposed to vibrations, it may damage the product and result in fire. When moving the product, turn the power off and disconnect t
Summary of the content on the page No. 9
Safety Instructions • The customer can return used or rechargeable batteries to a nearby public recycling center or to a store selling the same type of the battery or rechargeable battery. Do not place the product in a location exposed to direct sunlight or near any heat such as a fire or heater. • This may reduce the lifetime of the product, and may result in fire. Do not drop any objects onto the product or cause any impact to the product. • Otherwise, this may result in electric shock or fi
Summary of the content on the page No. 10
Introduction Package Contents Note Please make sure the following items are included with your LCD Display. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Checking the Contents of the Package Remove the lock from the package box, as shown in the figure above. Lift up the package box by Check the contents of the Remove the Styrofoam holding the grooves on package. and vinyl cover. both sides of the package box. Note • After unpacking the package, ma
Summary of the content on the page No. 11
Introduction LCD Display Manuals Quick Setup Guide Warranty Card User's Guide (Not available in all loca- tions) Cables Power Cord D-Sub Cable Others Remote Control Batteries (AAA X 2) BNC to RCA Adaptor Jack (BP59-00138A) (Not available in all loca- tions) Ferrite Core for Power Cord Sold separately DVI Cable Network Box Wall Mount KIT
Summary of the content on the page No. 12
Introduction Sold separately RGB to BNC Cable BNC to BNC Cable Semi Stand KIT Ferrite Core • The ferrite cores are used to shield the cables from interfer- ence. • When connecting a cable, open the ferrite core and clip it around the cable near the plug. Your LCD Display Front MENU button [MENU] Opens the on-screen menu and exits from the menu. Also use to exit the OSD menu or return to the previous menu. Navigate buttons (Up-Down buttons) Moves from one menu item to another vertically or adjust
Summary of the content on the page No. 13
Introduction Switches from PC mode to Video mode. Selects the input source that an external device is connected to. [PC] → [DVI] → [AV] → [Component] → [HDMI] → [MagicInfo] → [BNC] Note • MagicInfo can only be enabled when a network box is connected. • The HDMI port and network box cannot be connected at the same time. PIP button Push the PIP button to turn the PIP screen On / Off. More than one PIP cannot overlap on screen as BNC and the component use the same terminal. • PC : DVI / AV / Compo
Summary of the content on the page No. 14
Introduction POWER S/W ON [ │ ] / OFF [O] Switches the LCD Display On/Off. POWER The power cord plugs into the LCD Display and the wall outlet. RS232C OUT/IN (RS232C Serial PORT) MDC(Multiple Display Control) Program Port RGB IN (PC Connection Terminal (In- put)) • Use a D-Sub Cable (15 pin D-Sub) - PC mode (Analog PC) • Connect the RGB IN port on the monitor to the BNC port on the PC using the RGB to BNC cable. DVI IN (PC Video Connection Terminal) Connect the [DVI IN] port on the monito
Summary of the content on the page No. 15
Introduction DVI/RGB/HDMI AUDIO IN (PC/DVI/ HDMI Audio Connection Terminal (Input)) AV/COMPONENT AUDIO IN [R-AUDIO- L] Connect the port of the DVD, VCR (DVD / DTV Set-Top Box) to the [R-AUDIO-L] port of the LCD Display. DVI OUT • Connect a monitor to another monitor through a DVI cable. • Connect the [DVI OUT] port on the mon- itor to the [HDMI IN] port on the other monitor using the DVI to HDMI cable. • DVI, HDMI and network signals sent via the [DVI OUT] port are displayed on the second dis
Summary of the content on the page No. 16
Introduction BNC OUT [R, G, B, H, V] (BNC Terminal (Output)) BNC (Analog PC) Connection: connecting the R, G, B, H, V ports. The number of LCD Displays that can be connected to the loopout depends on the ca- bles, signal source, etc. With cables or signal source where there is no degradation, up to 10 LCD Displays can be connected (May not be supported depending on the connected cable). BNC/COMPONENT IN [R/Y, G/P , B/ B P , H, V] (BNC/Component Connection Ter- R minal (input)) - During BNC inp
Summary of the content on the page No. 17
Introduction POWER OFF Number Buttons DEL / GUIDE button - VOL + SOURCE D.MENU TOOLS Up-Down Left-Right buttons INFO COLOR BUTTONS TTX/MIX MTS/DUAL ENTER/PRE-CH MUTE CH/P TV MENU RETURN EXIT MagicInfo Turns the product On. 1. POWER Turns the product Off. 2. OFF 3. Number Buttons Press to change the channel. The "-" button is used to select Digital channels. 4. DEL / GUIDE but- Electronic Program Guide (EPG) display. ton - This function does not work for this LCD Display. 5. - VOL
Summary of the content on the page No. 18
Introduction - This function does not work for this LCD Display. 9. Up-Down Left-Right but- Moves from one menu item to another horizontally, vertically tons or adjusts selected menu values. Current picture information is displayed on the upper left 10. INFO corner of the screen. 11. COLOR BUTTONS Press to add or delete channels and to store channels to the favorite channel list in the “Channel List” menu. - This function does not work for this LCD Display. TV channels provide written informati
Summary of the content on the page No. 19
Introduction Returns to the previous menu. 19. RETURN Exits from the menu screen. 20. EXIT 21. MagicInfo MagicInfo Quick Launch Button. Note MagicInfo can only be enabled when a network box is con- nected. Mechanical Layout Mechanical Layout Installation VESA Bracket • When installing VESA, make sure to comply with the international VESA standards. • Purchasing VESA Bracket and Installation Information : Please contact your nearest SAMSUNG Distributor to place an order. After your order is pla
Summary of the content on the page No. 20
Introduction Dimensions Notice For securing the bracket on a wall, use only machine screws of 6 mm diameter and 8 to 12 mm length. Wall Bracket Installation • Contact a technician for installing the wall bracket. • SAMSUNG Electronics is not responsible for any damages to the product or harm to customers when the installation is done by the customer. • This product is for installing on cement walls. The product may not stay in place when installed on plaster or wood. Components Only use the comp
