Chamberlain 1225E FS2 user manual

User manual for the device Chamberlain 1225E FS2

Device: Chamberlain 1225E FS2
Category: Garage Door Opener
Manufacturer: Chamberlain
Size: 5.42 MB
Added : 11/10/2013
Number of pages: 80
Print the manual

Download

How to use this site?

Our goal is to provide you with a quick access to the content of the user manual for Chamberlain 1225E FS2. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Chamberlain 1225E FS2.

For your convenience

If looking through the Chamberlain 1225E FS2 user manual directly on this website is not convenient for you, there are two possible solutions:

  • Full Screen Viewing - to easily view the user manual (without downloading it to your computer), you can use full-screen viewing mode. To start viewing the user manual Chamberlain 1225E FS2 on full screen, use the button Fullscreen.
  • Downloading to your computer - You can also download the user manual Chamberlain 1225E FS2 to your computer and keep it in your files. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase.
Chamberlain 1225E FS2 User manual - Online PDF
Advertisement
« Page 1 of 80 »
Advertisement
Print version

Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual Chamberlain 1225E FS2 but the selected pages only. paper.

Summaries

Below you will find previews of the content of the user manuals presented on the following pages to Chamberlain 1225E FS2. If you want to quickly view the content of pages found on the following pages of the manual, you can use them.

Abstracts of contents
Summary of the content on the page No. 1

The Chamberlain Group, Inc.
845 Larch Avenue
Elmhurst, Illinois 60126-1196
®
GARAGE DOOR OPENER
For Residential Use Only
Model 1225E FS2
Model 1215E FS2
Owner’s Manual
■ Please read this manual and the enclosed safety materials carefully!
■ Fasten the manual near the garage door after installation.
■ Periodic checks of the opener are required to ensure safe operation.
■ The model number label is located on the front panel of your opener.

Summary of the content on the page No. 2

TABLE OF CONTENTS Introduction 2-8 Adjustment 29-31 Safety symbol and signal word review........................2 Adjust the travel limits ...............................................29 Preparing your garage door ........................................3 Adjust the force .........................................................30 Tools needed...............................................................3 Test the safety reversal system.................................31 Planning ............

Summary of the content on the page No. 3

1 Preparing your garage door WARNING WARNING Before you begin: To prevent possible SERIOUS INJURY OR DEATH: • Disable locks. • ALWAYS call a trained door systems technician if CAUTION WARNING • Remove any ropes connected to garage door. garage door binds, sticks, or is out of balance. An unbalanced garage door may not reverse when • Complete the following test to make sure your required. garage door is balanced and is not sticking or • NEVER try to loosen, move or adjust garage door, door bindi

Summary of the content on the page No. 4

— — — — — — — — • Look at the garage door where it meets the floor. Planning Any gap between the floor and the bottom of the Identify the type and height of your garage door. door must not exceed 6 mm. Otherwise, the safety Survey your garage area to see if any of the reversal system may not work properly. See conditions below apply to your installation. Additional Adjustment Step 3. Floor or door should be materials may be required. You may find it helpful to repaired. refer back

Summary of the content on the page No. 5

Slack in Chain Tension is Normal When Garage Door is Closed Planning (Continued) WARNING WARNING ONE-PIECE DOOR INSTALLATIONS Without a properly working safety reversal system, persons (particularly small children) could be • Generally, a one-piece door does not require CAUTION WARNING SERIOUSLY INJURED or KILLED by a closing garage reinforcement. If your door is lightweight, refer to door. the information relating to sectional doors in • The gap between the bottom of the garage door and Install

Summary of the content on the page No. 6

Planning (Continued) WARNING WARNING GATE INSTALLATIONS Without a properly working safety reversal system, persons (particularly small children) could be • It is recommended that you attach fine mesh or CAUTION WARNING SERIOUSLY INJURED or KILLED by a closing gate. screening across the inside of swinging or sliding • Activate gate ONLY when the gate is in full view and gates in order to prevent intruders from reaching free from any obstructions. through the bars and releasing the trolley from t

Summary of the content on the page No. 7

Carton Inventory Your garage door opener is packaged in two cartons Parts may be stuck in the foam. Hardware for which contains the motor unit and the parts illustrated assembly and installation is shown on the next page. below. Note that accessories will depend on the Save the carton and packing material until installation model purchased. If anything is missing, carefully and adjustment is complete. check the packing material. Model 1225E Only Model 1215E Only Model 1220E Only Model 1210E Onl

Summary of the content on the page No. 8

NOTICE Hardware Inventory Separate all hardware and group as shown below for the assembly and installation procedures. Assembly Hardware 41A3534 Hex Bolt Nut Washered Bolt Carriage Bolt 5/16"-18x7/8" (3) Master Link (2) 5/16"-18x1/2" (2) 5/16"-18 (5) 1/4"-20x1/2" (12) (mounted in opener) Trolley Lock Nut Lock Washer Threaded Shaft (1) 1/4"-20x7/16" (12) 5/16" (4) Installation Hardware 41A3535 Hex Bolt Lag Screw Lock Washer Nut 5/16"-9x1-5/8" (4) 5/16"-18x7/8" (4) 5/16" (6) 5/16"-18 (6) Ring Fast

Summary of the content on the page No. 9

ASSEMBLY STEP 1 HARDWARE SHOWN ACTUAL SIZE For Sectional and One-Piece Doors ONLY Assemble the Rail and Attach the Chain Pulley Bracket Carriage Bolts Lock Nut 1/4"-20x1/2" 1/4"-20 To avoid installation difficulties, do not run the garage door opener until instructed to do so. 1. Place the 3 rail sections on a flat surface for assembly. The end sections are Nut Lock Washer Hex Bolt identical. The center section must be 5/16"-18 5/16" 5/16"-18x7/8" positioned with the braces against the end secti

Summary of the content on the page No. 10

HARDWARE SHOWN ACTUAL SIZE ASSEMBLY STEP 1 For Sliding and Swinging Gates ONLY Assemble the Rail and Attach the Chain Pulley Bracket Carriage Bolts Lock Nut 1/4"-20x1/2" 1/4"-20 To avoid installation difficulties, do not run the garage door opener until instructed to do so. 1. Place the 3 rail sections on a flat Nut Lock Washer surface for assembly. The end Hex Bolt 5/16" 5/16"-18x7/8" 5/16"-18 sections are identical. Make sure the "arrow label" on the center section is pointing in the directio

Summary of the content on the page No. 11

HARDWARE SHOWN ACTUAL SIZE ASSEMBLY STEP 2 For Sectional and One-Piece Doors Only Install the Trolley • Attach the trolley threaded shaft to the trolley with Lock Washer Nut the lock washer and nuts as shown. 5/16" 5/16"-18 • As a temporary stop, insert a screwdriver into the Inner Nut hole in the front end of the rail. 5/16" Lock Washer • Slide the trolley assembly along the rail to the 5/16" Trolley screwdriver stop. Outer Nut Threaded 5/16" Shaft NOTE: If trolley hits against any nuts on the

Summary of the content on the page No. 12

WARNING WARNING ASSEMBLY STEP 3 CAUTION WARNING Fasten the Rail to the Motor Unit To avoid serious damage to opener, ONLY use bolts/fasteners mounted in top of motor unit. • Place the opener on packing material to protect the cover. For convenience, put a support under the chain pulley bracket. MODEL 1225E ONLY • Remove the two 5/16"-18x1/2" washered bolts mounted in the top of the motor unit. #8x1" • Align the holes in the back section of the rail with Washers Hex Screws the holes in the motor

Summary of the content on the page No. 13

ASSEMBLY STEP 4 WARNING WARNING For Sectional and One-Piece Doors Only To avoid possible SERIOUS INJURY to fingers from Install the Chain moving garage door opener: CAUTION WARNING and Attach the Sprocket Cover • ALWAYS keep hand clear of sprocket while operating opener. INSTALLING THE CHAIN • Securely attach sprocket cover BEFORE operating. Leave Chain 1. Dispense a few inches of & Cable Inside Carton to chain from carton and Prevent Kinking fasten to trolley with a Figure 1 master link from

Summary of the content on the page No. 14

5-15 cm ASSEMBLY STEP 4 WARNING WARNING For Sliding and Swinging Gates Only To avoid possible SERIOUS INJURY to fingers from Install the Chain moving opener: CAUTION WARNING and Attach the Sprocket Cover • ALWAYS keep hand clear of sprocket while operating opener. INSTALLING THE CHAIN • Securely attach sprocket cover BEFORE operating. Leave Chain & Cable 1. Dispense a few inches of Inside Carton to chain from carton and Prevent Kinking fasten to trolley with a master link from the hardware bag

Summary of the content on the page No. 15

ASSEMBLY STEP 5 Tighten the Chain Lock Washer Outer Nut • Spin the inner nut and lock washer down the Inner Nut trolley threaded shaft, away from the trolley. To Tighten Outer Nut • To tighten the chain, turn outer nut in the direction To Tighten shown. AS YOU TURN THE NUT, KEEP THE Inner Nut CHAIN FROM TWISTING. • When the chain is approximately 13 mm above the base of the rail at its midpoint, re-tighten the inner nut to secure the adjustment. Sprocket noise can result if chain is either too C

Summary of the content on the page No. 16

INSTALLATION STEP 1 Finished Ceiling Determine the Header Bracket 38 mm Header Location Board Structural Wall Supports WARNING WARNING To prevent possible SERIOUS INJURY or DEATH: • Header bracket MUST be RIGIDLY fastened to CAUTION WARNING structural support on header wall or ceiling, otherwise garage door might not reverse when required. DO NOT install header bracket over drywall. Vertical • Concrete anchors MUST be used if mounting header Centerline of Garage Door bracket or 38 mm board into

Summary of the content on the page No. 17

ONE-PIECE DOOR WITHOUT TRACK Unfinished Ceiling 1. Close the door and mark the inside vertical centerline of your garage door. Extend the line Structural Vertical onto the header wall above door, as shown. Supports Header Wall Centerline If headroom clearance is minimal, you can install 38 mm Board the header bracket on the ceiling. See page 18. 38 mm Board If you need to install the header bracket on a OPTIONAL 38 mm board (on wall or ceiling), use lag screws CEILING MOUNT FOR (not provided

Summary of the content on the page No. 18

INSTALLATION STEP 2 Install the Header Bracket You can attach the header bracket either to the wall Wall Mounting Holes above the garage door, or to the ceiling. Follow the CEILING MOUNT ONLY instructions which will work best for your particular The nail hole is for positioning only. requirements. Do not install the header bracket You must use lag screws UP to mount the header bracket. over drywall. If installing into masonry, use concrete anchors (not provided). WALL HEADER BRACKET INSTALLATI

Summary of the content on the page No. 19

INSTALLATION STEP 3 Attach the Rail to the Header Bracket • Position the opener on the garage floor below the Header Wall header bracket. Use packing material as a protective base. Header NOTE: If the door spring is in the way you’ll need Bracket help. Have someone hold the opener securely on a temporary support to allow the rail to clear the Chain Pulley spring. Bracket • Position the rail bracket against the header bracket. • Align the bracket holes and join with a clevis pin as shown. • Inser

Summary of the content on the page No. 20

WARNING WARNING INSTALLATION STEP 4 CAUTION WARNING Position the Opener To prevent damage to garage door, rest garage door opener rail on 38 mm board placed on top section of Follow instructions which apply to your door type as door. illustrated. SECTIONAL DOOR OR ONE-PIECE DOOR WITH TRACK A 38 mm board is convenient for setting an ideal door-to-rail distance. 38 mm Header Board Rail • Raise the opener onto a stepladder. You will need Bracket help at this point if the ladder is not tall enough.


Alternative user manuals
# User manual Category Download
1 Chamberlain 1000E - 1/4 HP User manual Garage Door Opener 188
2 Chamberlain 1000SDC 1/3HP User manual Garage Door Opener 30
3 Chamberlain 1140 User manual Garage Door Opener 17
4 Chamberlain 1025 User manual Garage Door Opener 18
5 Chamberlain 1000SDR 1/3 HP User manual Garage Door Opener 9
6 Chamberlain 1000SDC-R, 2000SDC-R User manual Garage Door Opener 3
7 Chamberlain 1022 User manual Garage Door Opener 11
8 Chamberlain 1042 User manual Garage Door Opener 2
9 Chamberlain 1146 User manual Garage Door Opener 1
10 Chamberlain 1024 User manual Garage Door Opener 3
11 Chamberlain 1145-1/3HP User manual Garage Door Opener 1
12 Chamberlain 1145 User manual Garage Door Opener 2
13 Chamberlain 1145- 1/3HP User manual Garage Door Opener 1
14 Chamberlain 1145jg User manual Garage Door Opener 3
15 Chamberlain 1150 User manual Garage Door Opener 4
16 Sony Remote Commander RM-V111T User manual Garage Door Opener 50
17 Sony RM-B750 User manual Garage Door Opener 22
18 Sony RCP 920 User manual Garage Door Opener 5
19 Aspire Digital ASPIRE RF RFKGT User manual Garage Door Opener 0
20 Aiphone IS-SS-HID-I User manual Garage Door Opener 0