Summary of the content on the page No. 1
LTC 0335 & LTC 0355
Installation Manual Installatiehandleiding
Digital Monochrome Digitale Zwart/Wit Camera
EN NL
Cameras
Manuel d’installation Manuale d’installazione
Caméra Numérique Noir et Videocamera Digitale in
FR IT
Blanc Blanco e Nero
Installationsanleitung Manual de Instruções
DE Digitale Schwarz-Weiß- PT Câmara Digital
Kamera Monocromática
Manual de instalación
Cámara Digitales de
ES ZH
Blanco y Negro
Summary of the content on the page No. 2
LTC 0335 & LTC 0355 | Installation Manual EN | 1 SAFETY PRECAUTIONS EN DANGER The lighting flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk to persons. InstallatiEN on Ma GLn IS uH al WARNING The exclamation point, within an equilateral triangle, is intended to alert the user to the presence of important operati
Summary of the content on the page No. 3
LTC 0335 & LTC 0355 | Installation Manual EN | 2 7. Do not defeat the purpose of a polarized or grounded mains plug. A polarized plug has dissimilar prongs (one wider than the other) to ensure correct polarity, while a grounded plug has an additional 'ground' prong provided for your safety. If the plug supplied with the apparatus does not fit into your outlet, consult an electrician for advice. 8. Protect the power-supply cord from being walked on or pinched, particularly close to plugs, r
Summary of the content on the page No. 4
LTC 0335 & LTC 0355 | Installation Manual EN | 3 FCC INFORMATION CAUTION Any changes or modifications to construction of this device that are not expressly approved by the party responsible for compliance could void the userfs authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a res
Summary of the content on the page No. 5
LTC 0335 & LTC 0355 | Installation Manual EN | 4 SPECIFICATIONS LTC 0335/x0 LTC 0355/x0 Standard resolution High resolution Standard CCIR EIA CCIR EIA Active pixels (H x V) 512 x 582 512 x 492 752 x 582 768 x 494 Imager 1/3" interline CCD Resolution 380 TVL 570 TVL Minimum illumination <0.12 lux <0.09 lux Signal-to-noise ratio > 50 dB Video output 1 Vpp, 75Ω Synchronization Internal or Line-Lock (selectable) Shutter Auto / Flickerless / Off (selectable) CCIR: 1/50 - 1/500000 - EIA: 1/60 - 1/600
Summary of the content on the page No. 6
LTC 0335 & LTC 0355 | Installation Manual EN | 5 Type number overview Low voltage High voltage CCIR (Eur.) EIA (USA) CCIR (Eur.) EIA (USA) Standard resolution LTC 0335/10 LTC 0335/20 LTC 0335/50 LTC 0335/60 High resolution LTC 0355/10 LTC 0355/20 LTC 0355/50 LTC 0355/60 UNPACKING Unpack carefully and handle the equipment with care. The packaging contains: • Camera • CCD protection cap • Spare lens connector (male) • These Instructions Note: If equipment appears to have been damaged during shi
Summary of the content on the page No. 7
LTC 0335 & LTC 0355 | Installation Manual EN | 6 To open the quick-connect, push in on the tabs. Connections are not polarity sensitive Use stranded or solid wire AWG16 to AWG22, cut back 10mm (0.4") of insulation. Composite Video LENS MOUNTING Pin Video iris lens DC iris lens 1 Supply (11 V, 50 mA max.) Damp- 2 Not used Damp+ 3 Video signal 1 Vpp, 1 kΩ Drive+ 4 Ground Drive- • Video-iris and DC-iris lenses are recommended for the best picture performance. • The camera automatically detects t
Summary of the content on the page No. 8
LTC 0335 & LTC 0355 | Installation Manual EN | 7 CAUTION • To avoid damaging the CCD sensor when using a C- mount lens, turn the 'green' back-focus ring counter clockwise until it stops ('Back focus adjustment') before mounting the lens. • Lenses weighing more than 0.5 kg (1.1lbs) must be separately supported. Note: If a short circuit is detected on the lens connector, the on-screen display (OSD) failure message 'LENS SHORT CIRCUIT' is shown. The lens circuit is automatically disabled to a
Summary of the content on the page No. 9
LTC 0335 & LTC 0355 | Installation Manual EN | 8 2. When back focusing vari-focus lenses, it must be possible to obtain a sharp picture in both wide-angle and tele positions, and for both far and near focus. 3. When back focusing zoom lenses, ensure the object of interest remains in focus throughout the entire zoom range of the lens. (See Advanced Set up). CAUTION Do not point the camera/lens into direct sunlight. When viewing an outdoor scene, a video- or DC-iris lens is recommended. MOUN
Summary of the content on the page No. 10
LTC 0335 & LTC 0355 | Installation Manual EN | 9 Hints for menu navigation How to use the 5 keys Up key Menu/select key Right key Left key Lock Down key • Press the menu/select key to access the menus or to move to the next or previous menu. • Press the menu/select key for approximately 1.5 seconds to open the Installer menu. • Use the up or down keys to scroll up or down through a menu. • Use the left or right keys to move through options or to set parameters. • When in a menu, quickly pre
Summary of the content on the page No. 11
LTC 0335 & LTC 0355 | Installation Manual EN | 10 Menu Navigation Press the menu button MAIN MENU SHUT/AGC MENU LEVEL 0 SHUTTER AES SHUT/AGC BLC OFF AGC ON AUTOBLACK ON SYNC LINE LOCK VPHASE 0¡ EXIT EXIT Main Menu Shutter/AGC Menu Press the menu button for more than 5sec. LENS WIZARD DETECTED LENS DCIRIS INSTALLER SET BACK FOCUS NOW VERSION 00.0010.XX LENS AUTO SPEED FAST LENS WIZARD EXIT WIZARD COAX COMM ON DETECTED LENS VIDEO DEFAULTS SET BACK FOCUS NOW EXIT SET LVL Lens Wizard Menus Install
Summary of the content on the page No. 12
LTC 0335 & LTC 0355 | Installation Manual EN | 11 Main menu Function Selection Description LEVEL -15 - 0 - +15 Adjusts video level. SHUT/AGC Select next menu Shutter / Automatic Gain Control menu. BLC ON ON When 'ON', the level is optimized at the center OFF of OFF the screen. Parts outside the center may be under- or over-exposed (this is normal). SYNC LINE LOCK Select 'LINE LOCK' to synchronize with the power INTERNAL supply frequency. Select 'INTERNAL' for use with internal synchronizati
Summary of the content on the page No. 13
LTC 0335 & LTC 0355 | Installation Manual EN | 12 Installer menu Function Selection Description VERSION Read-only firmware release number (for service purposes). LENS AUTO Automatically detect lens type. A different lens type can be selected. SPEED FAST Selects the response time of DC-iris lenses. Some lenses require slow lens control to avoid overshoots. WIZARD Access the lens wizard menu. COAX COM ON/OFF If OFF Bilinx™ communication is disabled DEFAULTS Select next menu Return all set-up se
Summary of the content on the page No. 14
LTC 0335 & LTC 0355 | Installation Manual EN | 13 Adjustment procedure DC-iris Lens: 1. Unlock the back focus locking button. 2. Access the "Lens Wizard" menu. 3. The "SET BACK FOCUS NOW" option is highlighted in the menu. 4. Turn the back focus adjustment as required. 5. Lock the back focus locking button. 6. Exit the menu. Adjustment procedure Manual-iris Lens: 1. Unlock the back focus locking button. 2. Adjust the lens to the maximum lens opening. 3. Turn the back focus adjustment as require
Summary of the content on the page No. 15
Bosch Sicherheitssysteme GmbH Bosch Security Systems B.V. Ludwig-Bölkow-Allee P.O. Box 80002 85521 Ottobrunn 5600 JB Eindhoven Germany The Netherlands www.bosch-sicherheitssysteme.de www.boschsecuritysystems.com 3122 165 22651 03-40 © 2003 Bosch Security Systems B.V. Subject to change Printed in Portugal
