Jensen JiSS-250i user manual

Summary of the content on the page No. 1

Portable Speaker Station for iPod & iPhone




























INSTRUCTION MANUAL

JiSS-250i

(iPod & iPhone not included)




Please read this Instruction Manual ca

Summary of the content on the page No. 2

IMPORTANT INSTRUCTIONS 1. Do not install the system near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 2. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 3. Only use attachments / accessories specified in these instructions. 4. Unplug this apparatus during lightning storms or when unused for long periods of tim

Summary of the content on the page No. 3

COMPLIANCE WITH FCC REGULATION This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonabl

Summary of the content on the page No. 4

LOCATION OF CONTROLS 1 2 3 4 5 6 1. LEFT SPEAKER 2. Docking Tray 3. Docking Connector 4. RIGHT SPEAKER 5. STANDBY BUTTON 6 VOLUME +/- BUTTON 7. AUX IN JACK 8. DC IN JACK 9. FOLDABLE STAND 10. BATTERY DOOR 7 8 9 10 9 POWER SOURCE This Portable Speaker System is designed to operate on 4 x 1.5V ‘AAA’ (UM-4) batteries (Not included) or

Summary of the content on the page No. 5

B. AC POWER CONNECTION 1. Plug the AC adaptor into a household 120V AC ~ 60Hz power source. 2. Insert the other plug into the DC INPUT Jack on the back of JiSS-250i. Note: The batteries will be automatically disconnected once the AC adaptor is plugged into the DC Jack and the System will operate on AC power. iPod ADAPTORS Below are the iPod Adaptors included in the package. iPod classic iPod touch nd rd iPod

Summary of the content on the page No. 6

DOCKING YOUR IPod 1. Fold out the STANDS located on the bottom of JiSS-250i. 2. Select a suitable adaptor attachment for your iPod/iPhone and insert it into the docking tray. Your iPod/iPhone can now be inserted onto the dock connector by aligning the connector on the bottom of the iPod onto the connector in the docking bay as shown below. For iPod/iPhone Landscape Viewing (iPod nano (4th gen), iPod touch, iPhone 2G, and iPhone 3G) proceed as below: 3. Choose the Correct ad

Summary of the content on the page No. 7

seconds to switch off the device and then gently remove it from the docking connector. 10. To turn JiSS-250i off, press the STANDBY Button again. Note: i. The System will automatically enter sleep mode 5 minutes after playback stops and switch to standby mode automatically after 30 minutes of no activity. In Sleep mode the LED will flash and in standby mode, the LED will go off. ii. The AUX In function is in higher priority than the iPod function. Make sure the AUX IN Jack is unplugge

Summary of the content on the page No. 8

TROUBLESHOOTING GUIDE Should you experience any difficulties in the use of this player please refer to the following chart or call 1 800 777 5331 for Product Service and Support. Symptom Possible Problem Solution Cannot dock iPod Using a wrong iPod adaptor Make sure the adaptor properly fits for your iPod. properly iPod is not installed Remove your iPod from the dock and check for any properly. obstruction on the connectors in the dock and on your iPod, then reseat it in the dock. iP