Summary of the content on the page No. 1
10/100Mbps Dual Speeds
Fast Ethernet
PC Card Network Adapter
Installation Guide
Summary of the content on the page No. 2
FCC REGULATORY STATEMENTS Part15, Class B This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interface, and 2. This device must accept any interface received, including interface that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable prot
Summary of the content on the page No. 3
HARDWARE INSTALLATION 1. Locate the PCMCIA slot of your system. 2. Align the PCMCIA Fast Ethernet PC Card toward the PCMCIA slot. Push evenly and steadily until it is seated. 3. Plug one end of an Ethernet Cable into the RJ-45 port of the Media Coupler. Media Coupler Ethernet HUB/Switch 4. You are now ready to continue the software installation. - 1 -
Summary of the content on the page No. 4
LED Indicators Act: Glows green when it is on, blinks when transmitting data. 10/100: Glows orange at 100Mbps, dims at 10Mbps. Link: Glows green when linked to a local network, blinks when receiving data. Green Activity: on TX : blink Orange Green 100Mbps: On Link Integrity: on 10Mbps :Off RX : blink - 2 -
Summary of the content on the page No. 5
SOFTWARE INSTALLATION Installation for Windows 95 The installation procedures for the network driver may vary slightly depending on the version of Windows 95 you are using and also your current system configuration. 1. Once the PCMCIA Fast Ethernet PC Card is connected to your computer, Windows 95 will automatically detect the new hardware device. Insert the program diskette #1 into your floppy drive. 2. Click Next. When the PCMCIA Fast Ethernet PC Card message appears, click Fini
Summary of the content on the page No. 6
2. Insert the device driver diskette into your floppy drive. When Windows prompts you What do you want Windows to do? Select Search for the best driver for your device. (Recommended). Click Next. 3. Follow the on-screen instruction to proceed. - 4 -
Summary of the content on the page No. 7
4. The installation program will proceed automatically. 5. In the following dialog box, direct your system to copy the requested files from the floppy root directory, i.e. A:\. Press OK. - 5 -
Summary of the content on the page No. 8
6. If you are asked to insert Windows 98 CD-ROM in the selective drive, please do so to have Windows copy all the necessary files to your system. . When the following window appears, click Finish. 7. Click Yes to restart your computer. Installation for Window ME 1. Once the PC Card is well connected to your computer, Windows ME will automatically detect the new device. Select Automatic search for a better driver (Recommended) … and click Next. - 6 -
Summary of the content on the page No. 9
2. Insert the device driver disk into the floppy disk drive on your system. 3. Windows will copy the appropriate driver to your system. If Windows ME asks you to supply your original Windows ME installation CD-ROM, load it on the CD- ROM drive. Click Finish to complete the software installation. - 7 -
Summary of the content on the page No. 10
4. Reboot your computer to activate the new device. Installation for Windows 2000 1. Insert the PC Card into the slot. When the Found New Hardware Wizard dialog box appears, press Next. 2. When Windows prompt you a Found New Hardware Wizard dialog box, select Search for a … and press Next. - 8 -
Summary of the content on the page No. 11
3. Windows will prompt a Found New Hardware Wizard dialog box. In this time, select Floppy disk drives and insert the driver diskette. Press Next. When asked for the original Windows 2000 CD/disks please follow the on-screen instruction. - 9 -
Summary of the content on the page No. 12
4. Wait for a while until Windows has found the appropriate driver. 5. Click Yes to continue. 6. Click Finish. The PC Card driver installation is successfully completed. - 10 -
Summary of the content on the page No. 13
7. For the first time installation, click Network icon in Control Panel to add Protocols, Client and Service if needed. 8. Reboot your computer to activate the new device. Installation for Windows XP 1. Once the device is well connected, Windows will detect the new device and prompt you to insert the network device driver. Insert the device Driver Disk into the floppy disk drive of your system. Click Install the software automatically (Recommended) and click Next. - 11 -
Summary of the content on the page No. 14
2. Windows will start searching for the appropriate driver for this hardware. Select any drivers named as PCMCIA Fast Ethernet Card, and click Next. 3. Windows will start searching for the appropriate driver for the installation. - 12 -
Summary of the content on the page No. 15
When the screen appears as below, click Continue Anyway to proceed. 4. Wait while Windows copies the appropriate driver to your system. 5. Click Finish. The software installation for this network device is now completed. - 13 -
Summary of the content on the page No. 16
Installation for Windows NT 4.0 This section describes the installation for Windows NT under the condition that Windows NT is already installed in your computer. If your computer is not yet networking installed, refer to the Windows documentation for details. Also remember to have your original Windows NT CD-ROM handy before you begin the installation. For Windows NT may ask for it during the installation. 1. Before you turn on your computer, make sure the PCMCIA Fast Ethernet PC Car
Summary of the content on the page No. 17
8. When the Network window reappears, click on the Bindings tab. Choose your bindings. Click on the Protocols tab and select your settings. Do the same for the Services tab. 9. After your bindings, settings, and services are set, click on the Close button. Choose to restart your computer. After Windows NT restarts, be sure to log in. - 15 -
