Summary of the content on the page No. 1
USB V.90
FAX/MODEM
Quick Installation Guide
M73-APO08-380
Summary of the content on the page No. 2
FCC REGULATORY STATEMENTS The United States Federal Communication Commission (FCC) and the Canadian Department of Communications have established certain rules governing the use of modems and other electronic equipment. FCC Part 68 Registration This high speed USB 56K FAX/MODEM complies with FCC Part 68 rules, and the use of this modem is subject to the following restrictions: 1. The FCC has established rules which permit this device to be directly connected to the telephone networ
Summary of the content on the page No. 3
FCC Part 15 Registration This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interface, and 2) This device must accept any interface received, including interface that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against h
Summary of the content on the page No. 4
CTR 21 pan-European Certification This equipment has been approved in accordance with Council Decision 98/482/EC for pan-European single terminal connection to the public switched telephone network (PSTN). However, due to differences between the individual PSTNs provided in different countries, the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point. In the event of problems, you should contact your equipment s
Summary of the content on the page No. 5
Introductions The USB V.90 Fax/Modem is fully compatible with the Universal Serial Bus functionality built in Windows 98/2000/ME/XP. Installation is easy and no external power is required. You can now enjoy the advantage of all the benefits offered with USB technology. Providing the fastest possible Internet access up to 56K, the USB V.90 Fax/Modem is faster than any other conventional Fax/Modem. System Requirements A Pentium processor-based personal computer 166MMX or above.
Summary of the content on the page No. 6
Parts Names and Functions USB connection cable: connects the USB host port to the USB V.90 FAX/MODEM. 6 connects to the USB host port 5 4 3 1 2 USB-B: USB device port. LINE jack: connects to the phone line. OH LED indicator: glows when it is in on- line status. Ready LED indicator: glows when the device is well installed. Rx/Tx LED indicator: blinks when the USB V.90 Fax/Modem is transmitting/receiving data. - 2 -
Summary of the content on the page No. 7
HARDWARE INSTALLATION 1. Locate the USB host port of your system. Align the USB connector toward the USB host port. Push evenly and steadily until it is seated. 2. Connect the other end of the USB connection cable to the device port (USB B) of the USB V.90 Fax/Modem until it clicks. 3. Connect your phone line to the LINE jack. Software Installation Installation for Windows 98 1. When the USB V.90 Fax/Modem is well connected to your computer, Windows 98 will automatically detect
Summary of the content on the page No. 8
will start searching for the appropriate driver for the software installation. 4. Click Next. 5. Click Finish. The software installation is successfully complete. 6. When the following dialog box appears, select the country/location where you are, and click Enable PBX. Click OK. - 4 -
Summary of the content on the page No. 9
7. When finished, restart your computer to activate the new device. Installation for Windows 2000 1. When the USB V.90 Fax/Modem is well connected to your computer, Windows 2000 will automatically detect the new device. Click Next. 2. Select Search for a suitable driver for my device (recommended) and click Next. - 5 -
Summary of the content on the page No. 10
3. Insert the new device driver compact disc into the CD-ROM drive. Select Specify a location and click Next. 4. Click Browse button and select the drive where you load the device driver (for example: E:\WIN2K). Click OK. Windows will start searching for the appropriate driver for the software installation. - 6 -
Summary of the content on the page No. 11
5. Click Next to continue. 6. Click Yes. 7. Click Finish. - 7 -
Summary of the content on the page No. 12
8. When Windows prompt you “Modem Country Selection”, choose the country where you locate. Select the Enable PBX check box and click OK. The software installation is then complete. 9. The software installation is successfully complete. - 8 -
Summary of the content on the page No. 13
Installation for Windows ME 1. When the USB V.90 Fax/Modem is well connected to your computer, Windows ME will automatically detect the new device. Select Specify the location of the driver (Advanced) and click Next. 2. Load the device driver compact disc into the CD-ROM of your system and select Specify a location. Click the Browse button to select the drive where you load the device driver (for example: F:\WinME). Click Next. - 9 -
Summary of the content on the page No. 14
3. Expect a minor delay for Windows to search for the appropriate driver for the device. Click Next. 4. Click Finish. The installation program will continue. - 10 -
Summary of the content on the page No. 15
5. Select Specify the location of the driver (Advanced) and click Next. - 11 -
Summary of the content on the page No. 16
6. When the above figure appears, repeat step 2, namely, select Specify a location. Click the Browse button to select the drive where you load the device driver (for example: F:\WinME). Click Next. 7. Click Next. - 12 -
Summary of the content on the page No. 17
8. When Windows prompt you “Modem Country Selection”, choose the country where you locate. Select the Enable PBX check box and click OK. 9. Click Finish to complete the installation. - 13 -
Summary of the content on the page No. 18
Installation for Windows XP 1. When the USB V.90 Fax/Modem is connected to your computer, Windows XP will automatically detect the new device. Select Install from a list or specific location (Advanced) and click Next. 2. Load the device driver compact disc into the CD-ROM of your system and select Include this location in the search. Click - 14 -
Summary of the content on the page No. 19
the Browse button to select the drive where you load the device driver (for example: D:\WinXP). Click Next. 3. Click Continue Anyway. 4. Expect a minor delay for Windows to search for the appropriate driver for the device. 5. Click Finish to complete the software installation. - 15 -
Summary of the content on the page No. 20
- 16 -
