Summary of the content on the page No. 1
1.0 Key Features
• Convert any USB 2.0 / 1.1 mass storage device into a Network Attached
Storage device
• Great for adding Addonics Storage Tower, Storage Rack or any
Addonics USB storage device onto the network
• USB port can be use to power most 2.5" USB hard drive or any low
power USB devices
• Connect a USB printer to share it over the network
Addonics
• One Fast Ethernet 10/100Mbps port
T E C H N O L O G I E S • Can be set as a DHCP server or client depending
Summary of the content on the page No. 2
Network Environment Note: “SDisk utility” was written with JAVA script, please make sure your There are 3 different setup conditions you can choose: computer has installed JAVA before, if not please install the JAVA script form the CD drive. A. Setup NAS Adapter as a DHCP Client: If your NAS adapter is connected to a LAN network with an active DHCP server, it will obtain an IP address from DHCP server automatically. B. Setup NAS Adapter as DHCP Server: If your LAN network does no
Summary of the content on the page No. 3
Status Provide the basic information for NAS Adapter. Date/ Time Setting Identification You can change time setting from this page. Clicks “Apply” to save the setting. You can change and modify your host, group name and password from this page. Click “Apply” to save the setting. By default SNTP is set to Network Time Service otherwise select synchronize to PC. If internet access is available, we recommended setting SNTP to Network Host name: This is used to identify your dev
Summary of the content on the page No. 4
IP Configuration By default, “IP Config” is set to “Automatic IP”. This will allow the NAS adapter to obtain its IP address automatically. If you prefer setting it manually, select the static IP option, enter your own value and click “Apply” to confirm the new setting. Maintenance This page allows you to update the NAS adapter firmware, to go back to factory default settings or reboot NAS system. Disk Utility Firmware update: Follow the steps below to update the loader an
Summary of the content on the page No. 5
Click “Modify” to share a folder. Select “User1” from Folder List and click the “à” to add user on “Sharing List”. SMB Server SMB server allows you to share data or files through the network LAN. When a USB storage device is connected, a default Public folder is available to be shared among Guest users. A default Guest user is also created. Note: Only use English alphabet for folder names and no special characters when creating new folders. To Access the folder How t
Summary of the content on the page No. 6
Type “User1” and password to login. Enter new password then click “Apply” to save setting. How to delete a SAMBA account Now you have set up the folder that you wish to share on your NAS adapter. This Select an account you wish to delete. Click “Delete” to proceed. Please folder can be access from other computer on your local network. note that all the data inside the folder will be lost after the delete. How to modify account password Select “User1” and then cli
Summary of the content on the page No. 7
FTP Server Remember to “Enable” the FTP service on the status page, when you plan on using the FTP server. FTP server Configuration: The standard port for FTP service is 21. If required, you can change it from any port between 1025-65500. But in general, we recommended using the default port of 21. File language support: By default, the encoding is set to English. If you want to store or transfer files with a different encoding (different language), choose the corresponding languag
Summary of the content on the page No. 8
Same procedure applies for the Music and Video folders. On your Xbox 360, go to “Media” tab, select either Music or Pictures and press A button of the Xbox console to continue. XBOX 360 Media Server The Media server can be used to share your photo and music files stored on the NAS adapter with an X-BOX360 video game console from Microsoft. Before you start, make sure both devices are connected to the same local network and turned on. Press X
Summary of the content on the page No. 9
Printer Server Inside the share folder, you can access your picture or music files, depending on which mode you are currently using. Select the files you would like to see or to listen, and start playback. 1. Install printer driver, (for example. if Epson PL-6200L Printer is connected to the NAS adapter, you must install PL-6200L driver into the computer first.) After driver installation, click “Start” “Setting” “Printer and Faxes” “Add a printer” “Next”.
Summary of the content on the page No. 10
2. Connect USB printer to NAS adapter. Your network environment should be similar with diagram below: 3. Select “Local printer” and click “Next” to continue. 5. Enter the NAS adapter IP address then click “Next” to continue. 4. Select “Create a new port type of port:” then choose “Standard TCP/IP Port” then click “Next” to continue. 6. Select “Custom” and go to “Setting”.
Summary of the content on the page No. 11
8. Click “Finish” to complete TCP/IP printer setup. 7. Select “LPR” under protocol, and give a queue name eg:LRxxx; select LPR Byte Counting Enabled then click “OK” to finish the port setting. Note: The NAS adapter printer server does not support GDI/Host-based printers. For some Multi Function Printers (MFP); scanning functions might not be functional probably. Please contact Printer Manufacture for detail Specifications. Bit Torrent server The NAS adapter su
Summary of the content on the page No. 12
1. Select “Bit Torrent” and select the “Download Path” you wish to use. Mail Notification Then click “Apply” to save setting. (DO NOT change path setting while After a download is successful, an email will be sent to the designated email performing BT download, otherwise downloading jobs will disappear) address. Click “Mail setup” and input SMTP server, recipient email, SMTP 2. Server Port range can be from 6881 to 65535. (6881 is default setting) A/C, Password, than click “Apply” to save set
Summary of the content on the page No. 13
Mac installations (Mac 10.5.4 or above) 3. Click on the Storage-xxxx (or the correct name of the NAS adapter). Open the Mac browser “Safari” and key-in the host name of the NAS adapter (for example, “Storage-0000”). It will detect the NAS adapter automatically. How to setup SAMBA in Mac OS X 10.5.4 1. Click “Go” on the toolbar, and select ”Network” as the screenshot shown below. 4. Select the folder you wish to share, and click “OK” to share the folder. 2. Double Click
Summary of the content on the page No. 14
How to Map your NAS Adapter to your system. Showing NAS Disk Drive in network Map Network Window appears 1. Press “Start” button on Windows desktop 2. Press “Search” 3. Select Folders 4. Select Computer or people 5. Select a computer on the network and a new window will appear. 6. Key in the host name, (For example “storage-xxxx”) in the “Computer name” column and then press “Search” button. You will see the following window. Note: For faster connection and usability, we recomm
Summary of the content on the page No. 15
Technical Support If you need assistance to get your unit functioning properly, please call Addonics Technical Support. Our technical staff will be happy to assist you, but they will need your help to do so. Calling the technical support staff without all the proper information can be both time consuming and frustrating. Here are some tips to help you out: MODEL NUMBER – Please have this number on hand. SYSTEM INFORMATION – Type of computer, peripherals, etc. OPERATING SYSTE
