Summary of the content on the page No. 1
GE
Security
GE-DS-242-PoE Managed
Ethernet Switch User Manual
P/N 1069174 • REV 1.0 • ISS 22FEB10
Summary of the content on the page No. 2
Copyright © 2010 GE Security, Inc. This document may not be copied in whole or in part or otherwise reproduced without prior written consent from GE Security, Inc., except where specifically permitted under US and international copyright law. Disclaimer The information in this document is subject to change without notice. GE Security, Inc. (“GE Security”) assumes no responsibility for inaccuracies or omissions and specifically disclaims any liabilities, losses, or risks, personal or othe
Summary of the content on the page No. 3
Content Chapter 1 Introduction 1 Package Contents 2 Product Description 2 How to Use this Manual 3 Product Features 4 Product Specifications 7 Chapter 2 Installation 11 Hardware Description 12 Switch Installation 15 Chapter 3 Switch Management 21 Requirements 22 Management Access Overview 22 Web Management 23 SNMP-Based Network Management 25 Administration Console 25 Protocols 27 Management Architecture 28 Chapter 4 Web-Based Management 29
Summary of the content on the page No. 4
Chapter 6 Command Line Interface 127 Operation Notice 127 System Commands 128 Switch Static Configuration 129 Trunk Configuration 135 VLAN Configuration 138 Misc Configuration 147 Administration Configuration 149 MAC limit 154 Port Mirroring Configuration 155 Quality of Service 156 MAC Address Configuration 159 STP/RSTP Commands 162 SNMP 167 IGMP 171 802.1x Protocol 173 Access Control List 177 Binding 182 Power over Ethernet Commands 184
Summary of the content on the page No. 5
Chapter 1 Introduction The GE Security GE-DS-242-PoE offers 24 10/100Mbps Fast Ethernet ports with 2 Gigabit TP/SFP combo ports (Port-25, 26). The two Gigabit TP/SFP combo ports can be either 1000Base-T for 10/100/1000Mbps or 1000Base-SX/LX through SFP (Small Form-Factor Pluggable) interface. The GE-DS-242-PoE has a high performance switch architecture that is capable of providing non-blocking switch fabric and wire-speed throughput as high as 8.8Gbps. Its two built-in GbE uplink po
Summary of the content on the page No. 6
Chapter 1: Introduction Package Contents What’s in the box Open the Managed Switch box and carefully unpack it. The box should contain the following items: The Managed Switch x1 User’s manual CD x1 Installation Sheet x1 19” Rack mount accessory kit x1 Power cord x1 Rubber feet X4 RS-232 cable x1 If any of these are missing or damaged, please contact your dealer immediately. If possible, retain the carton including the original packing material, and use them to repack the produc
Summary of the content on the page No. 7
Chapter 1: Introduction Power Over Ethernet The PoE in-line power following the standard IEEE 802.3af makes the GE-DS-242-PoE able to power on 24 PoE devices at a distance of up to 100 meters through the 4-pair Cat 5/5e UTP wire. Cost-effective solution with SNMP monitor for Network deployment GE Security releases the cost-effective Managed Switch not only for catering to the need of easy WEB-based management, but also the centralized SNMP application to monitor the status of Switch and
Summary of the content on the page No. 8
Chapter 1: Introduction Product Features • Physical Port o 24-Port 10/100Base-TX RJ-45 with PoE Injector o 2-Port Gigabit TP/SFP combo interfaces o Reset button for system management o 1 RS-232 male DB9 console interface for Switch basic management and setup • Layer 2 Features o Complies with the IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3z Gigabit Ethernet standard o High performance Store and Forward architecture, broadcast storm control, runt/CRC filtering eliminates erroneo
Summary of the content on the page No. 9
Chapter 1: Introduction IEEE 802.1p Class of Service IP TOS / DSCP code priority Port Base priority o Strict priority and weighted round robin (WRR) CoS policies o Ingress/Egress Bandwidth control on each port • Multicast o IGMP Snooping v1 and v2 o IGMP Query mode for Multicast Media application o 256 multicast groups • Security o Layer 2 / 3 / 4 Access Control List (ACL) o IEEE 802.1x Port-Based Authentication o MAC address Filtering and MAC address Binding o IP address secur
Summary of the content on the page No. 10
Chapter 1: Introduction o Auto detect powered device (PD) o Circuit protection prevent power interference between ports o Remote power feeding up to 100m o PoE Management Total PoE power budget control Per port PoE function enable/disable PoE Port Power feeding priority Per PoE port power limit PD classification detection PoE Power Supply Over temperature Protection 6 GE-DS-242-PoE Managed Ethernet Switch User Manual
Summary of the content on the page No. 11
Chapter 1: Introduction Product Specifications GE-DS-242-PoE HARDWARE SPECIFICATIONS 10/100Mbps Copper Ports 24 10/100Base-TX RJ-45 Auto-MDI/MDI-X ports 1000Mbps Copper Ports 2 10/100/1000Base-T RJ-45 port SFP/mini-GBIC Slots 2 SFP interfaces, shared with Port-25 and Port-26 Switch Architecture Store-and-Forward Switch Fabric 8.8Gbps / non-blocking Switch Throughput 6.547Mpps@64Bytes Address Table 8K entries Share Data Buffer 512Kbytes Flash 4Mbytes DRAM 16Mbytes Maximum Frame S
Summary of the content on the page No. 12
Chapter 1: Introduction Port disable/enable Auto-negotiation 10/100Mbps full and half duplex mode selection Port Configuration Flow Control disable / enable Bandwidth control and broadcast storm filter on each port Display each port's speed duplex mode, link status, flow control status, Port Status auto-negotiation status Port-Based VLAN, up to 26 VLAN groups VLAN IEEE 802.1q Tagged Based VLAN , 4K VLAN ID, up to 256 VLAN groups IEEE 802.1d Spanning Tree Spanning Tree IEEE 802.1w
Summary of the content on the page No. 13
Chapter 1: Introduction PoE Power Supply Type End-Span PoE Power Output Per Port 48V DC, 350mA . Max. 15.4 watts Power Pin Assignment 1/2(+), 3/6(-) PoE Power Budget 380 Watts Max. number of Class 2 PD 24 Max. number of Class 3 PD 24 Standards Conformance Safety FCC Part 15 Class A, CE IEEE 802.3 10Base-T IEEE 802.3u 100Base-TX IEEE 802.3z Gigabit SX/LX IEEE 802.3ab Gigabit 1000Base-T IEEE 802.3x Flow Control and Back pressure Standards Compliance IEEE 802.1d Spanning tree protoco
Summary of the content on the page No. 14
Chapter 1: Introduction 10 GE-DS-242-PoE Managed Ethernet Switch User Manual
Summary of the content on the page No. 15
Chapter 2 Installation This section describes the hardware features and installation of the Managed Switch on the desktop or rack mount. For easier management and control of the Managed Switch, familiarize yourself with its display indicators and ports. Front panel illustrations in this chapter display the unit’s LED indicators. Read this chapter completely before connecting any network device to the Managed Switch. GE-DS-242-PoE Managed Ethernet Switch User Manual 11
Summary of the content on the page No. 16
Chapter 2: Installation Hardware Description Switch Front Panel The Switches front panel provides a simple interface for monitoring the Managed Switch. Figure 2-1 shows the front panel of the Managed Switch. Figure 2-1: GE-DS-242-PoE Switch front panel 10/100Mbps TP Interface Port-1~Port-24: 10/100Base-TX Copper, RJ-45 Twist-Pair: Up to 100 meters. Gigabit TP Interface Port-25, Port-26: 10/100/1000Base-T Copper, RJ-45 Twist-Pair: Up to 100 meters. Gigabit SFP Slots Port-25
Summary of the content on the page No. 17
Chapter 2: Installation Reset button At the left of front panel, the Reset button is designed to reboot the Managed Switch without turning the power off. The following table summarizes the Reset button functions: Reset Button Pressed and Released Function About 1~3 seconds Reboots the Managed Switch Resets the Managed Switch to Factory Default configuration. The Managed Switch will then reboot and load the default settings as below: • Default Password: admin Until the PWR LED goes
Summary of the content on the page No. 18
Chapter 2: Installation • System LED Color Function PWR Green Lit: indicates there is power to the Switch • Per 10/100Base-TX, PoE interfaces (Port-1 to Port-24) LED Color Function Lit: indicates the link through that port is successfully established LNK/ACT Green Blink: indicares the Switch is actively sending or receiving data over that port Lit: indicates the port is providing 48VDC in-line power PoE In Use Orange Off: indicates the connected device is not a PoE Powered
Summary of the content on the page No. 19
Chapter 2: Installation Switch Rear Panel The rear panel of the Managed Switch includes an AC inlet power socket, which accepts input power from 100 to 240VAC, 50-60 Hz. Figure 2-3 shows the rear panel of the Managed Switch. Figure 2-3: GE-DS-242-PoE Rear panel 3 2 POWER NOTICE: 1. The Managed Switch is a power-required device: it will not work unless it is receiving power. If your networks must be active at all times, it is recommended that the Switch be connected to a UPS (Unint
Summary of the content on the page No. 20
Chapter 2: Installation Step 3: Ensure there is enough ventilation space between the Managed Switch and surrounding objects. Figure 2-4: Typical placement of GE-DS-242-PoE on desktop NOTE: Connection to the Managed Switch requires UTP Category 5 network cabling with RJ-45 tips. Refer to the Cabling Specification in Appendix A for further information. Step 4: Connect the Managed Switch to network devices. A. Connect one end of a standard network cable to the 10/100/1000 RJ-45 ports o
