Summary of the content on the page No. 1
HP NC7770 PCI-X
Gigabit Server Adapter
User Guide
June 2007 (Second Edition)
Part Number 336419-00B
Summary of the content on the page No. 2
© 2003, 2007 Hewlett-Packard Development Company, L.P. Broadcom® is a registered trademark of Broadcom Corporation and/or its subsidiaries. Hewlett-Packard Company shall not be liable for technical or editorial errors or omissions contained herein. The information in this document is provided “as is” without warranty of any kind and is subject to change without notice. The warranties for HP products are set forth in the express limited warranty statements accompanying such products. Nothing
Summary of the content on the page No. 3
HP Contents About This Guide Technician Notes...........................................................................................................................................v Where to Go for Additional Help.................................................................................................................vi Telephone Numbers...............................................................................................................................vi Chapter 1 In
Summary of the content on the page No. 4
Contents Appendix C Specifications NC7770 PCI-X Gigabit Server Adapter Specifications............................................................................ C-1 UTP Cable Specifications ......................................................................................................................... C-2 Using UTP Category 5 Cable in Gigabit Over Copper Installations.................................................. C-2 RJ-45 Pinouts and Crossover Function.......................
Summary of the content on the page No. 5
About This Guide Use this guide as reference when installing and maintaining the HP NC7770 PCI-X Gigabit Server Adapter. WARNING: To reduce the risk of personal injury from electric shock and hazardous energy levels, only authorized service technicians should attempt to repair this equipment. Improper repairs can create conditions that are hazardous. Technician Notes WARNING: Only authorized technicians trained by HP should attempt to repair this equipment. All troubleshooting
Summary of the content on the page No. 6
About This Guide NOTE: Any indications of component replacement or printed wiring board modifications may void any warranty. Where to Go for Additional Help HP updates networking software frequently to include new functionality and features. Complete the following steps to get the latest drivers, firmware, and documentation. 1. Go to the HP website (http://www.hp.com). 2. Click Support and Troubleshooting Information from the left menu bar. 3. Type the product name in the for product
Summary of the content on the page No. 7
1 Introduction Overview The HP NC7770 PCI-X Gigabit Server Adapter is a high-performance Ethernet adapter with a fully integrated 10/100/1000 controller that delivers up to 1000 Mb/s Ethernet over twisted-pair (copper) cabling. The HP NC7770 adapter has one auto-negotiating RJ-45 port and LED indicators showing link, activity, and port speed. The NC7770 PCI-X Gigabit Server Adapter is a supported option for selected HP ProLiant servers. For the latest functionality, features, and operat
Summary of the content on the page No. 8
Introduction LED Indicators The following table describes the LED indicators located on the front panel of the HP NC7770 Server Adapter. Table 1-1: 10/100/1000 LED Operations for the NC7770 Adapter LED Display Description 1000 On Link to the adapter is established. The adapter is sending or receiving network data at 1000 Mb/s. Off The adapter is not sending or receiving network data at 1000 Mb/s. 100 On Link to the adapter is established. The adapter is sending or receiving network
Summary of the content on the page No. 9
2 Installing the Adapter Overview This chapter describes installation precautions and explains how to install the adapter. It also describes how to connect the network cable. WARNING: To avoid the risk of personal injury or damage to the equipment, consult the safety information and user documentation provided with your equipment before attempting installation of the adapter. Many servers are capable of producing energy levels that are considered hazardous. Users should not remove
Summary of the content on the page No. 10
Installing the Adapter Installing the Adapter in a Server Refer to the HP ProLiant server documentation for additional information on how to safely install a PCI card in your server. Figure 2-1: Installing the adapter in a server WARNING: If the server is not PCI Hot Plug compliant, power it down and unplug the power cord from the power outlet before removing the server cover. Failure to do so may damage the adapter or server. 1. Remove the server cover and cover bracket from a
Summary of the content on the page No. 11
Installing the Adapter Connecting the Network Cable Network connections for the NC7770 Server Adapter can employ existing Category 5 UTP (or better) cable for Gigabit over copper transmissions. For new installations, Category 5e (enhanced Category 5) or better cable is recommended. To secure the cable, plug the cable connector into the RJ-45 port. Ensure that the tab on the plug clicks into position indicating that it is properly seated. For more information, see “UTP Cable Specifications
Summary of the content on the page No. 12
A Regulatory Notice Federal Communications Commissions Notice Part 15 of the Federal Communications Commission (FCC) Rules and Regulations has established Radio Frequency (RF) emission limits to provide an interference-free radio frequency spectrum. Many electronic devices, including computers, generate RF energy incidental to their intended function and are, therefore, covered by these rules. These rules place computers and related peripheral devices into two classes, A and B, depending
Summary of the content on the page No. 13
Regulatory Notice Class B Equipment This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,
Summary of the content on the page No. 14
Regulatory Notice For questions regarding this FCC declaration, contact: Hewlett-Packard Company P. O. Box 692000, Mail Stop 510101 Houston, Texas 77269-2000 Or, call (281) 514-3333 To identify this product, refer to the Part, Series, or Model number found on the product. Canadian Notice (Avis Canadien) Class A Equipment This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe A respecte tou
Summary of the content on the page No. 15
Regulatory Notice European Union Notice Products bearing the CE marking comply with the EMC Directive (89/336/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community and if this product has telecommunication functionality, the R&TTE Directive (1999/5/EC). Compliance with these directives implies conformity to the following European Norms (in parentheses are the equivalent international standards and regulations): • EN 55022 (CISPR 22)—Electromag
Summary of the content on the page No. 16
Regulatory Notice Japanese Notice PCI-X Notice When this product is used in PCI-X mode, it is a “Class A” device. HP NC7770 PCI-X Gigabit Server Adapter User Guide A-5
Summary of the content on the page No. 17
B Electrostatic Discharge Overview To prevent damage to the system, be aware of the precautions you need to follow when setting up the system or handling parts. A discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices. This type of damage may reduce the life expectancy of the device. To prevent electrostatic damage, observe the following precautions: • Avoid hand contact by transporting and storing products in static-sa
Summary of the content on the page No. 18
C Specifications NC7770 PCI-X Gigabit Server Adapter Specifications Table C-1: NC7770 PCI-X Gigabit Server Adapter Specifications Specification Description Network Controller Chipset Broadcom® 5701KHB Data Transfer Method 64-bit/133MHz PCI-X, compatible with 64-bit/66MHz or 32-bit/66MHz Bus Master DMA Power Requirement Operating Voltage: +5V +/- 5% Power Consumption: 10 Watts Maximum: 2A @ 5V(DC) Standards Supported IEEE 802.3ab, 802.3u, 802.1p, 802.1z Dimensions 6.6 x 2.5 inches
Summary of the content on the page No. 19
Specifications UTP Cable Specifications To connect to the network, the NC7770 Server Adapter uses the following cable for 1000BASE-T transmission. Category 5 UTP or better 22-26 AWG, 100Ω @ 1MHz EIA/TIA 568a or EIA/TIA 568b Using UTP Category 5 Cable in Gigabit Over Copper Installations For Gigabit over copper installations, Category 5 UTP or better 1000BASE-T cable must comply with the IEEE 802.3ab 1000BASE-T standard. For new installations, Category 5e (enhanced Category 5) or better
Summary of the content on the page No. 20
Specifications Figure C-1: 10/100 straight-through wiring for RJ-45 connector 10/100 Crossover Pinouts When the crossover function is not provided within the hub or switch, you must implement the crossover through the twisted-pair media using the physical pinouts indicated in Table C-3. Table C-3: 10/100 Pinouts Using External Crossover Pin Function Color/Match Function Pin 1 TD+ White/Orange RD+ 3 2 TD- Orange/White RD- 6 3 RD+ White/Green TD+ 1 4 Blue/White 5 White/Blue
