Summary of the content on the page No. 1
NOTES 9
Video Flex 7700 Specifications (Network Interface)
Model 7700
Hardware CPU 32Bit RISC Processor
OS Embedded Linux
Flash Memory 4MB
Viewer Web Browser based Monitoring
Network Protocol TCP/IP, HTTP, FTP, SMTP, PPP, UDP
Interface 10 base-T Ethernet (RJ-45)
Compression Algorithm M-JPEG
Rate 1/10 ~ 1/200
Video Input 1CH. NTSC/PAL
Output 1CH. NTSC/PAL
Size 640 ´ 480, 320 ´ 240, 160 ´ 120
Frame Rate 30 frame/sec (320 ´ 240)
Power DC12V / 500mA
Operating Temperature 0°C ~ 40°C
Summary of the content on the page No. 2
CONTENTS FAQ 8 1. Introduction 3 I want to prevent users from viewing my camera. w Go into Administration Tools of the 7700. About This Manual 3 w Click on Users. Notes Before Starting 3 w Delete the user or all users by deleting the ID and password associated with that user. 2. 7700 Installation 4 Can I record the video? Product Description 4 Yes, you can record, but you will need to purchase a separate Quick Start 6 software program to allow PC-based record
Summary of the content on the page No. 3
FAQ 8 INTRODUCTION 1 How do I find out my IP address information if my settings were auto- About This Document matically detected? If you have previous knowledge of networking, you will most likely be best Windows 98 / ME Users served by the Quick Start Guide (page 6). w Open an MS-DOS Prompt w At the prompt type: "winipcfg" (without the quotation marks) If you are new to networking and have no previous knowledge of the sub- w Use the drop down list to select your 10/100 Ethernet Adapter jec
Summary of the content on the page No. 4
7700 INSTALLATION 2 FAQ 8 Product Description Frequently Asked Questions Back Panel I can't connect! In the case of a connection failure, follow this sequence, letting each device finish fully rebooting: Power Supply Connector Modem Reboot Use the power jack to connect your regulated 12V DC power Router Reboot adapter. 7700 Reboot How do I choose a unique IP address that matches my network? 10M LED For your home or small office, ensure that all devices on your network are running. PING an IP
Summary of the content on the page No. 5
APPENDIX7 7700 INSTALLATION 2 Top View Power Indicator C: Port Forwarding This red switch becomes illuminated when 12V DC After assigning the 7700 a web server port and video server port you must use Port power is supplied to the unit and the switch is Forwarding for Case B (using a router with a static IP address provided by the ISP). depressed. This indicator should always be lit when Please consult your router's user guide on how to correctly configure Port Forwarding. in use. If it is not
Summary of the content on the page No. 6
7700 INSTALLATION 2 APPENDIX 7 Quick Start B: Changing your computer's IP address and subnet mask Please follow the steps below to complete the initial setup of the Video Flex For Windows 98 / ME Users 7700. Start w Please do not power on the 7700 until instructed. Setting w Temporarily disable any proxy servers configured in Internet Control Panel Explorer. Network w If connecting the 7700 directly to a modem, power down and Configuration tab reset the modem. Leave the modem powered down unt
Summary of the content on the page No. 7
APPENDIX7 7700 INSTALLATION 2 11. Configure the 7700's TCP/IP settings as you would any other PC A: Determining Current TCP/IP settings on your network, providing a proper IP address, subnet mask, For Windows 98 / ME Users default gateway, and DNS server. w If this is standalone unit with a direct connection to a Start cable/DSL/Broadband modem then input the addresses you have Setting received from your ISP. Control Panel 12. The 7700 utilizes two TCP ports - a Web Server Port for ut
Summary of the content on the page No. 8
7700 SETUP 3 ADMIN TOOL6 7700 Initial Setup via a Crossover Cable Users Tool This section provides a guide on how to connect the 7700 to your PC/laptop for initial setup. Please follow the instructions in the order they appear, without skipping steps. Do not supply power to the 7700, until instructed. In order to access the 7700's firmware you will need to connect the 7700 directly to a PC or laptop computer via the supplied crossover cable. 1. Before you begin, you must determine the current
Summary of the content on the page No. 9
ADMIN TOOL 6 7700 SETUP 3 6. Now you will be able to access the viewer software with Date & Time Tool in the 7700 A. Open Internet Explorer and type the IP address of 192.168.1.80 (default IP of the 7700 from the factory) into the Address Bar of the web browser (as seen below). Press Enter. B. If a message appears after pressing "Enter" similar to the image depicted below, choose "Try Again". This message will vary depending on the operating system. Current Date/Time It shows the cur
Summary of the content on the page No. 10
NETWORK SETUP4 APPENDIX7 Guide to Network Setup SMTP Tool Please configure the 7700 at the location of its installation. You must This function is used to email the specified email recipient and notify that determine your network scenario in order to configure the 7700 with the individual of the IP address / web port number used to access the 7700. proper TCP/IP settings. This tutorial will guide you through the process. Before This email function only activates when the 7700 is powered on and
Summary of the content on the page No. 11
ADMIN TOOL6 NETWORK SETUP 4 TCP/IP Tool Case A: Static (Fixed) IP on a LAN (Local Area Network) Configure your 7700's TCP/IP properties as follows: Network Type STATIC Internet Address A private IP address such as 192.168.0.200 [Example] A. You need to assign the 7700 an IP address, just as you would assign a PC. B. The IP address you assign must be unique on your network as assigned by a network administrator to avoid IP conflicts. C. The IP address you assign the 7700 must be a private I
Summary of the content on the page No. 12
NETWORK SETUP4 ADMIN TOOL 6 This section is provided to familiarize the user with the administration tools. Case B: Static (Fixed) IP + Personal Router Intuitive options are not explained in detail. Must have at least 2 static IP's received from your ISP. All the options under Administration Tools take effect in real time the instant the new settings are applied. These settings will be global, affecting all users cur- Configure your 7700's TCP/IP properties as follows: rently logged on. Network
Summary of the content on the page No. 13
WEB VIEWER5 NETWORK SETUP 4 Viewer Screen Case C: Static (Fixed) IP [Dedicated line directly to the 7700] This section is designed to familiarize you with the main interface of the 7700. Displaying the OSD and Digital Zoom are only taking place on the local Configure your 7700's TCP/IP properties as follows: machine, not on the unit itself. To make global changes on the 7700 and its video, you must login as an administrator. Network Type STATIC Internet Address A static IP address received from
Summary of the content on the page No. 14
NETWORK SETUP 4 NETWORK SETUP 4 Port Forwarding Starting the 7700 After entering the correct TCP/IP settings you will be ready for "Port Forwarding" After correctly forwarding the Web Server Port and the Video Server Port (Case B). through your router (if applicable), you may then install the 7700 in a proper location. w Please record the TCP/IP settings of your 7700 for future reference. You may need this information to access your 1. Connect the 7700 to your router, switch, hub, or cable/D
