Summary of the content on the page No. 1
network-electronics.com
Flashlink User Manual
ASI-IP-GTW
DVB-ASI to IP
Gateway
Rev. 2.10.0
Summary of the content on the page No. 2
ASI-IP-GTW User's Manual This page is intentionally left blank Page 2
Summary of the content on the page No. 3
ASI-IP-GTW User's Manual Important notice: Network Electronics ASA reserve the right to make corrections, modifications, enhancements, improvements and other changes to its products or services at any time and to discontinue any product or service without notice. About this manual This manual explains how to operate the ASI-IP-GTW IP to ASI Video Gateway. It is shown how to install and maintain the unit. In addition, the functionality of the unit is described in detail. This manual
Summary of the content on the page No. 4
ASI-IP-GTW User's Manual Page 4
Summary of the content on the page No. 5
ASI-IP-GTW User's Manual Table of Contents 1 Introduction ................................................................................ 8 1.1 Purpose of this Manual ......................................................... 8 1.1.1 Who Should Use this Manual................................................... 8 1.1.2 Warnings, Cautions and Notes................................................. 8 1.2 Contact Information.............................................................. 9 1.2.
Summary of the content on the page No. 6
ASI-IP-GTW User's Manual 3.5.2 Time settings ..........................................................................33 3.5.3 Alarms....................................................................................34 3.5.4 SNMP .....................................................................................34 3.5.5 Ping........................................................................................36 3.5.6 Security...........................................................
Summary of the content on the page No. 7
ASI-IP-GTW User's Manual 6.4.2 Preliminary Checks................................................................ 71 6.4.3 PSU LED Unlit / Power Supply Problem................................. 72 6.4.4 Fan(s) Not Working / Overheating.......................................... 73 6.4.5 Alarm LED lit / Alarm condition ............................................ 73 6.5 Disposing of this Equipment ............................................... 75 6.5.1 General...............................
Summary of the content on the page No. 8
ASI-IP-GTW User's Manual 1 Introduction 1.1 Purpose of this Manual This manual describes how to operate the ASI to IP Gateway, hereafter referred to as the ASI-IP-GTW. It also describes how to install and maintain the unit. A detailed technical description of the functionality of the unit is given as part of this document. The following topics are covered in this manual: o General introduction to the ASI-IP-GTW o Installation of the Unit o Functional description of the Unit o Fault
Summary of the content on the page No. 9
ASI-IP-GTW User's Manual Caution: Cautions give information, if strictly followed, will prevent damage to equipment or other goods. Note: Notes provides supplementary information. They are highlighted for emphasis, as in this example, and are placed immediately after the relevant text. 1.2 Contact Information Our primary is to provide first class customer care that is tailored to your specific business and operational requirements. Telephone: +47 33 48 99 99 Fax: +47 33 48 99
Summary of the content on the page No. 10
ASI-IP-GTW User's Manual 1.2.2 Software versions This manual covers the functionality of the software version 1.4.0 or later of the ASI-IP-GTW. This manual continues to be relevant to subsequent software versions where the functionality of the equipment has not changed. When a new software version changes the functionality of the product, a new version of this manual will be provided. 1.3 Role of the ASI-IP-GTW in a Typical System The ASI-IP-GTW provides a bridge between the MPEG-2 wor
Summary of the content on the page No. 11
ASI-IP-GTW User's Manual o Type of Service (TOS) field support for reliable end-to-end transmissions o User-friendly configuration and control o WEB/XML based remote control o Easy access to unit from any WEB browser o Easy integration to Network Management System (NMS) with SNMP Trap support Page 11
Summary of the content on the page No. 12
ASI-IP-GTW User's Manual 1.5 Guided Tour 1.5.1 The User Interface All connectors are provided at the rear panel. Configuration and monitoring of the unit is performed via a FLASH-based WEB interface using a standard WEB browser such as Internet Explorer. The unit also supports configuration via file transfer of XML files. Once configured, the unit runs without the need for further intervention unless system configuration requirement change. 1.5.2 Front Panel Description The front pane
Summary of the content on the page No. 13
ASI-IP-GTW User's Manual Note: Some units are delivered to use 48 VDC power. These units have a 3-pin power D-SUB connector instead of the mains connector. 7. LEDs. The ASI-IP-GTW provides on the rear four LEDs related to the operation of the equipment. In addition, there are LEDs related to the ASI ports, the management port and the data port. 1.5.4 Construction The ASI to IP Gateway consists of a main board and one or two ASI boards mounted horizontally in a screened, self-ventila
Summary of the content on the page No. 14
ASI-IP-GTW User's Manual 1.5.6 Software Options The following table describes the features available as software option. Please refer to Appendix D: Upgrade of Features for more information Table 2. Functionality enabled through software licenses Functionality Max value Description Number of enabled ports 8 The number of ASI ports enabled. This can be different from the number of ports physically mounted. Data port max. speed: 1000Mbit/s The speed of the data port can be 100Mbit/
Summary of the content on the page No. 15
ASI-IP-GTW User's Manual 2 Installing the Equipment 2.1 Introduction 2.1.1 Read this first! The ASI-IP-GTW must be handled carefully and thoughtfully to prevent safety hazards and damage. Ensure that the personnel designated to install the unit have the appropriate skills and knowledge. Follow the instructions for installation and only use installation accessories recommended by the manufacturer. 2.1.2 To inspect package content o Inspect the shipping container for damage. If your sh
Summary of the content on the page No. 16
ASI-IP-GTW User's Manual o Where appropriate ensure that this product has an adequate level of lightning protection. Alternatively, during a lightning storm or whenever it is left unattended and unused for long periods of time, unplug it from the supply outlet and disconnect the output equipment. This prevents damage to the product due to lightning and power-line surges. Warning: If the Video Gateway has been subject to a lightning strike or the power surge which has stopped it working,
Summary of the content on the page No. 17
ASI-IP-GTW User's Manual GTW are no not blocked and allow at least 50 mm free air-space at each side of the unit. The ASI-IP-GTW is designed to be stacked in 19"racks without ventilation panels between. In systems with stacked units, it may be required to use forced-air cooling to reduce the operating ambient temperature. Figure 4 shows the air path through the unit. Figure 4. Air Path through the unit 2.2.6 To connect the equipment Once the ASI-IP-GTW is installed in its intended o
Summary of the content on the page No. 18
ASI-IP-GTW User's Manual have ordered the unit with less than 4 ASI ports, the enabled ports starts at number 1 up to the number of ports ordered. In IP bi-directional mode, half the DVB-ASI connectors are used as inputs, and the other half as DVB-ASI outputs. ASI connectors 1, 2, 5 and 6 are used as inputs, while ASI connectors 3, 4, 7 and 8 are used as outputs. 1.1.1.10 Ethernet data port Connect the Ethernet data port to the network. In IP transmit mode, the ASI-IP-GTW will send an
Summary of the content on the page No. 19
ASI-IP-GTW User's Manual Warning: If the moulded plug fitted to the mains cable supplied with this unit is not required, please dispose of it safely. Failure to do this may endanger life as live ends may be exposed if the removed plug is inserted into a mains outlet. Caution: Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the poin
Summary of the content on the page No. 20
ASI-IP-GTW User's Manual Warning: If the terminal screw has to be replaced, use an M4x12mm long pozidrive panhead. Using a longer screw may cause a safety hazard. 1.1.1.17 Connecting the Video Gateway to the AC Power Supply Warning: Do not overload wall outlets and extension cords as this can result in a risk of fire or electrical shock. As no power switch is fitted in this unit, ensure that the local ac power supply is switch off before connecting the supply cord. The unit is not fitte
