Summary of the content on the page No. 1
1-port H.323/SIP E1/T1
Trunk Gateway
VIP-2100
Summary of the content on the page No. 2
CONTENTS Chapter 1 VIP-2100 Introduction .................................................................1 SYSTEM DESCRIPTION .................................................................................... 1 TECHNICAL SPECIFICATION.............................................................................. 2 AUDIO FEATURE ............................................................................................. 2 VIP-2100 DETAIL SPECIFICATIONS..............................
Summary of the content on the page No. 3
DIGIT MANIPULATION .................................................................................... 50 CALL FLOW EDITOR...................................................................................... 50 CONFIGURATION MANAGER ........................................................................... 50 APPLY CHANGE............................................................................................ 51 Chapter 7 Advance Configuration Reference .............................
Summary of the content on the page No. 4
Appendix 4 Interface LED Description .................................................. 116 Appendix 5 Build-in Voice Prompt Index................................................ 117 Appendix 6 Timezone to Country Mapping List...................................... 118 Appendix 7 IP Bandwidth Requirement................................................... 120 Appendix 8 Release Complete Cause Code............................................ 121 Appendix 9 RADIUS Format Attributes........
Summary of the content on the page No. 5
VIP-2100 User’s manual - 4 -
Summary of the content on the page No. 6
Chapter 1 VIP-2100 Introduction System Description VIP-2100 is a cost effective solution for VoIP trunk gateway supporting one-, port T1/E1 VoIP trunks that provides voice and fax over IP network. It supports ITU-T H.323 V3, SIP RFC 2543/3261, SNMP V2, Call Detail Record, WEB management and other useful functions to meet customer requirements. The built-in enhanced IVR (Interactive Voice Response) and Billing Service of VIP-2100 is suitable for prepaid and postpaid service. It can ra
Summary of the content on the page No. 7
- Multiple configuration saving - Provides CDR (Call Detail Record) - Built-in internal user authentication for prepaid & postpaid users Technical Specification Interface - Two 10/100MB Ethernet Ports (Host & VoIP stream) - 1 xT1/E1 (120 Ohm-RJ48C connectors) 75 Ohm needs external 3rd party BNC/RJ-48C adapter cables Protocol and Standard - ITUT H.323 v3 and H.450 compliance - SIP RFC 2543/3261 compliance Audio Feature - Codec -- G.711 A/μ-Law, G.723.1 (5.3K/6.3K), G.729A,
Summary of the content on the page No. 8
- Selected disconnect cause code & behavior Management Feature - OS and program upgradeable - Console port: RS-232 port - TELNET - Full Web management interface & real time monitor - Front panel LCD - SNMP v2 (H.341) and SNTP v4 support - User account management - Time zone and day light saving support - Support fixed IP and DHCP - Support DNS and dynamic DNS LED indicators for system status - Power/Storage access indicators lines - Front panel LCD (2 x 16) status display
Summary of the content on the page No. 9
VIP-2100 Detail Specifications Feature VIP-2100 Physical Dimension 1 Width 483mm 2 Height 44mm 3 Depth 450mm 4 Industrial rack mount Yes 5 Color Black 6 Weight 8Kg Power / Environmental 1 Power 90-240V auto switch 2 Operating temperature 0~60 C 3 Relative humidity 5%~95% Processors & Storage 1 DSP vendor Intel Pentium, AudioCodes DSP 2 Operation System XP Embedded 3 RAM 512 MB 4 Program/Data Storage 256 MB DOM 5 OS Upgradeable Yes 7 Progra
Summary of the content on the page No. 10
E&M Bell Core Feature Group D, Wink Start, E&M Delay Start, E&M Feature Group A Immediate Start, E&M Feature Group B Wink Start, E&M Feature Group D Wink T1 CAS DTMF/R1MF Start(ANI B4 ADDR), E&M Feature Group D Wink Start, E&M Immediate Start, E&M Wink Start, GroundStart FXO, GroundStart FXS, Loop Start FXO, Loop Start 7 FXS, Loop Start FXO Hot-Line NI2 ISDN,5ESS 10 ISDN,DMS100 T1 ISDN PRI Support ISDN, NTT ISDN (INS-1500), Hong 8 Kong, QSIC Trunk Spans 9 1 (T1/E1s) per chassis
Summary of the content on the page No. 11
3 G.168 (Echo Cancellation) Yes (32ms) 4 Gain Control Yes 5 Improved Echo Tail Suppression Yes 6 Silence Suppression Yes 7 VAD Yes Maintenance 1 Administrative Log Yes 2 Auto Daylight Saving Yes 3 Customizable Time Zone Yes 4 Front Panel LCD Setup Yes 5 FTP Server Yes 6 HTTP server Yes 7 HTTP SSL support Yes 8 Multiple configuration Yes 9 NTP time synchronization Yes (SNTP V4) 10 Password Security Yes 11 RS232 Yes 12 System Event Log Yes 13 Teln
Summary of the content on the page No. 12
SIP Protocol Support 1 Cause Code Mapping Yes 2 HTTP Digest Authentication Yes 3 SIP Call on Hold Yes 4 SIP Early Media Yes 5 SIP Overload Redirect Yes 6 SIP Transfer (unattend) Yes 7 SIP Transfer (attend) Yes 8 SIP/TCP Yes 9 SIP/UDP Yes 10 SIP-180/SDP Yes 11 SIP-183/SDP Yes 12 SIP-PRACK Yes 13 SIP-RFC 3261 Yes 14 SIP-RFC 3264 (Offer/Answer) Yes H.323 Gatekeeper Support 1 Gatekeeper Register Yes 2 Direct call Yes 3 Routed call Yes 4 Light
Summary of the content on the page No. 13
7 H.323 to SIP FAX Relay Yes 7 PSTN to H.323 Call Yes 8 PSTN to PSTN Call Yes 9 PSTN to SIP Call Yes 10 SIP to H.323 Call Yes 11 SIP to PSTN Call Yes 12 SIP to SIP Call Yes 13 SIP to SIP Fax Relay Yes 14 VoIP to VoIP RTP unRouted Yes 15 VoIP to VoIP RTP Routed Yes Enhance Service 1 ANI Access List Yes 2 DNIS Access List Yes 3 DID/DOD Yes 4 PSTN Two Stage Dialing Yes 5 VoIP Two Stage Dialing Yes Yes (Random, Round Robin, 6 Intelligent PSTN Call Ro
Summary of the content on the page No. 14
6 VoIP Prepaid Support Yes Embedded AAA 1 Embedded Prepaid Service Yes 2 Embedded Postpaid Service Yes 3 Point/second Calculation Yes 4 Second/point calculation Yes 5 Auto Disable/Clean User Yes 6 PSTN Prepaid Support Yes 7 VoIP Prepaid Support Yes System Limitation 1 Max DM 4096 2 Max IP ACL 2048 3 Max DNIS ACL 4096 4 Max ANI ACL 4096 5 Max User ACL 20000 6 Max Phone Book Entries 10000 7 Max Call Flow Component 256 8 Max CDR Keep Days 5 9 Max
Summary of the content on the page No. 15
VIP-2100 Appearance Description VIP-2100 Front Panel: 7 8 2 5 1 3 4 6 Functions: 1: Power LED 2: Network1 Interface LED 3: Network2 Interface LED (not used) 4: H/D LCD 5: Power Switch 6: System Status LED 7: LCD Panel 8: LCD Touch Panel VIP-2100 Rear Panel: 3 7 6 8 9 10 1 5 4 2 Functions: 1: Electric Fan 2: AC Power outlet 3: AC Power switch (Keep on) 4: Trunk E1/T1 port 5: VoIP Ethernet port 6: Keyboard/Mouse 7: Com1 port
Summary of the content on the page No. 16
Chapter 2 Logon VIP-2100 After connected E1/T1 & Ethernet cables into the VIP-2100, turned on the power. The first step is to logon the system and set up the IP address. Before you can use the Browser to setup VIP-2100, you need to have Java Standard Runtime (1_4_1_02) to make it work. Please refer to Appendix 2 Java plug-in Install for detail. Logon VIP-2100 Setp1: Start IE5.0 (or later version) to navigate VIP-2100 Management System by typing the default IP address (the d
Summary of the content on the page No. 17
Step 3: The screen shows the Home Page of VIP-2100 as figure 2.1-3. Figure 2.1-3 Network Configuration Step 1: After successfully logon to the system, we need to change the network configuration. Click Control→Network to setup the network parameters as figure 2.2-1. Figure 2.2-1 VIP-2100 User’s manual - 12 -
Summary of the content on the page No. 18
Step 2: Enter the deserved IP address, Submask and default gateway. Apply the change by clicking apply button as figure 2.2-2. Figure 2.2-2 Step 3: When screen shows “Setup network configuration successfully!” It means the IP Network setting is successfully changed as figure 2.2- 3. Figure 2.2-3 ☻Note: “Network Control” takes around 5-second to apply the new network configuration. Please logon again with new IP address after 5 seconds. System Time Configuration
Summary of the content on the page No. 19
Figure 2.3-2 Step 3: Enter current date and time. Apply the change by clicking Apply button as figure 2.3-3. Figure 2.3-3 Step 4: The screen will shows “Setup system time successfully!” It means the System Time setting is successfully changed as figure 2.3-4. Figure 2.3-4 Step 5: If you would like to use SNTP to sync time with a SNTP V4 Server, click Time Sync button to setup it as figure 2.3-5. Figure 2.3-5 Account Manager Step 1: You can manage your user account
Summary of the content on the page No. 20
Figure 2.4-2 Field Description: • User ID: Login User ID • Password: Login Password • Confirm Password: Confirm new password again Step 3: When screen shows “Create user account successfully!” It means user account setting is successfully created as figure 2.4-3 Figure 2.4-3 ☻Note: The system provides 2 USER ID by default: User 1: “root” Password: “root” User 2: “admin” Password: “admin” VIP-2100 User’s manual - 15 -