Summary of the content on the page No. 1
HP PS1810-8G Switch Quick Setup Guide,
and Safety/Regulatory Information
For more detailed instructions and information to set up your switch, view or download the Installation and Getting Started
Guide for your switch at www.hp.com/networking/support.
1. Unpack and check included parts. ■ Documentation kit
■ Switch
■ Accessory kit (installation hardware)
■ Wall mount AC/DC adapter, or in-line AC/DC adapter and
power cord
2. Prepare for installation. To avoid personal injury or product damage,
Summary of the content on the page No. 2
Wall Mounting: Install two 5/8-inch (15.875 mm) Number 12 wood screws, (included) into the mounting surface, positioned 6.3 inches (160 mm) apart. Use the wall anchors if necessary. Then, position the switch over the screws and slide to lock in place. 3 2 Important: For wall-mounting, the network ports must be 1 facing up or down. (See “Installation Precautions” on page 6.) 2 1 Under-Surface Mounting: Install the two screws on the surface bottom similarly to the procedures for wall mount
Summary of the content on the page No. 3
4. Connect the network cables. Connect network devices, such as an HP ProLiant MicroServer Gen8, to any of the switch’s RJ-45 ports using Class 5E or better Ethernet cables. Note: Any of the switch’s network ports can be used for the following connections. You do not have to use the specific ports shown in the illustrations. As shown in the following illustration, for connection to a HP ProLiant MicroServer Gen8, it is recommended that you make the following connections: ■ ➊ to ➋ – to provide
Summary of the content on the page No. 4
5. Power on and verify that Self-Test completes normally. The switch does not have a power switch. It is powered on by connecting the AC power adapter supplied with your switch. 3 2 1 1 2 After Self-Test: Power LED = On Fault LED = Off 6. Configure the switch (minimal configuration). Note: These procedures assume that you have a Dynamic Host Configuration Protocol (DHCP) service in the network to which the switch is connected. The DHCP service automatically provides a network IP address co
Summary of the content on the page No. 5
7. (Optional) Configure trunking (link aggregation) on the switch and another network device that supports that feature. One of the significant features on the HP PS1810-G Switch is trunking, or link aggregation. This feature provides twice the bandwidth for connections, such as to the HP ProLiant server, and provides redundancy in case one of the connections is lost. See the “Trunking” chapter in the switch Management and Configuration Guide for the procedures to configure and monitor trunki
Summary of the content on the page No. 6
Safety and Regulatory Information for HP PS1810-8G Switch To avoid personal injury or product damage when installing your switch, read the installation precautions and guidelines below. Installation Precautions Warnings ■ Do not wall-mount any switch without checking for restrictions in the Installation and Getting Started Guide. ■ Wall-mount the switch with network ports facing up or down (away from or toward the floor). ■ If mounting the switch under HP ProLiant MicroServer Gen8s, stack no
Summary of the content on the page No. 7
Product Specifications HP PS1810-8G Switch (J9833A) Electrical: For power, requires one of the following: • External power adapter module. See “PS1810-8G External Power Adapters and Power Cords:” on page 8 � or, PoE PD connection to Port 1. Port 1 is an IEEE 802.3af Compatible PD (PoE Powered Device) - Class 3. Environmental: Operating Temperature: 0°C to 40°C (32°F to 104°F) Relative humidity: 15% to 95% at 40°C (104°F), non-condensing Non-Operating Temperature: -40°C to 70°C (-40°F to 158°
Summary of the content on the page No. 8
PS1810-8G External Power Adapters and Power Cords: Universal inline power adapter (5066-1122*) AC power cord: specifications: 8121-0870 Australia / New Zealand 8121-0664 Philippines / Thailand 8120-8373 China – AC Input Voltage: 100-240 V 8121-0702 India – Maximum AC Input Current: 0.5 A 8120-6314 Indonesia / Israel / Vietnam – AC Input Frequency Range: 50/60 Hz 8120-6316 Japan 8120-6317 South Africa – Power Consumption: 15 W 8120-8441 South Korea – DC Output Voltage: 12 ± 10% V 8121-0963 Taiw
