Summary of the content on the page No. 1
INSTALLATIO N INSTRUCTIO NS
Automated Tilt Mounting System
CM8
Summary of the content on the page No. 2
Installation Instructions DISCLAIMER Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice
Summary of the content on the page No. 3
Installation Instructions LEGEND Tighten Fastener Pencil Mark Apretar elemento de fijación Stram fastspændingsbeslag Marcar con lápiz Blyantmærke Befestigungsteil festziehen Skruva åt fäste Stiftmarkierung Pennmarkering Apertar fixador Kiristä kiinnike Marcar com lápis Piirretty merkki Serrare il fissaggio Dokr ci element mocuj cy Segno a matita Oznaczenie o ówkiem Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Ba lant S n Marquage au crayon Kalem areti Rögzít meghúzás
Summary of the content on the page No. 4
Installation Instructions TOOLS REQUIRED FOR INSTALLATION 3/16" (5mm) #2 1/2" (12.5mm) - masonry PARTS A (1) B (1) C (1) C1 (1) G (1) F (1) E (1) G1 (8) G2 (6) G3 (6) D (1) M4x16mm M4x20mm M4x25mm G4 (6) G6 (6) G5 (6) M5x16mm M5x25mm M5x20mm G9 (1) M5 J (1) H (1) G7 (6) G8 (6) M6x16mm M6x25mm H2 (4) H1 (4) 5/16" x 2-1/2" G12 (4) 5/16" G10 (6) G11 (6) M8x50mm M8x20mm M8x30mm H4 (4) H3 (2) G15 (8) 10-24 x 1/2" G13 (8) G14 (8) .750x.323x.250 .750x
Summary of the content on the page No. 5
Installation Instructions DIMENSIONS 5
Summary of the content on the page No. 6
Installation Instructions INSTALLATION 1 WARNING: IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SEVERE PERSONAL INJURY OR DAMAGE TO EQUIPMENT! It is the installers responsibility to make certain the structure to which the mount is being attached is capable of supporting five times the weight of the CM8 and all attached equipment not to exceed 150 lbs (68 kg). NOTE: Instructions are included for installing the CM8 in a wood stud wall or a solid concrete wall application. Proceed to the
Summary of the content on the page No. 7
Installation Instructions Concrete Installation 1 2 1b NOTE: Mount the wall bracket in four spots, spaced a minimum horizontal distance of 12" (30.5cm). x 4 1. Level wall bracket (B) and mark locations of pilot holes. 1/2" x 2-1/2" (12.5mm x 63.5mm) 2. Drill four 1/2" x 2-1/2" (12.5mm x 63.5mm) pilot holes into mounting surface. 3 (H4) x 4 3. Install four anchors (H4) into pilot holes, inserting end that opens slightly first. Tap with hammer until flush with concrete surface. 4. Using a socket
Summary of the content on the page No. 8
Installation Instructions Attaching Brackets to Display Mounting 2 Slots WARNING: IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Only use hardware provided or specified by manufacturer. 1 NOTE: Locate Digital Optical Audio Output on back of display (if available). 5 1. Determine and mark the vertical center position between the left side upper and lower mounting holes in display. 2. Determine and mark the verti
Summary of the content on the page No. 9
Installation Instructions Installing Display 3 WARNING: IMPROPER INSTALLATION CAN LEAD TO DISPLAY FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! Ensure mounting bracket hooks are completely engaged over wall bracket. 1 CAUTION: DISPLAY MAY WEIGH IN EXCESS OF 40 LBS! Always use two people and proper lifting techniques when installing or positioning display on wall bracket. 1. Slide wall bracket (B) side latches out. 2. Place display on wall bracket (B) by hooking the bracket (B
Summary of the content on the page No. 10
Installation Instructions Connecting Electrical Components 4 Electrical Rating: DC 12V; 0.4A CAUTION: DAMAGE TO CABLES POSSIBLE! Do not run cables or wires near the moving parts of this mount. 1. Plug the AC adapter (E) into the CM8 control box and the home’s electrical socket. (E) 2. Plug the IR receiver (F) into the CM8 control box, and attach the head to bottom side of display. 1 NOTE: The CM8 detects whether the display is ON or OFF by detecting whether the LED light (red) from the Digital
Summary of the content on the page No. 11
Installation Instructions Adjusting Tilt 5 NOTE: Remove plastic tab from remote control (J) before use. 1. Use the down arrow button on the remote control (J) to fully tilt down the display. AUTO MANU RESET NOTE: The CM8 is designed to tilt the display down a maximum of 13°. The maximum tilt angle may vary 1 depending on the application. Tilt Down 2. Visually check to see if the display tilts down fully. If the display does NOT tilt down fully, proceed to STOP Section 6. If the display DOES
Summary of the content on the page No. 12
Installation Instructions Removing Spring to Tilt Display 6 1. Remove and keep two Phillips screws from plastic cover on non-motorized bracket (C). 2 x 1 2. Remove and keep one Phillips screw from latch. 3. Lower latch to remove spring. 4. Return latch to original position. 3 1 x 2 5. Store spring in plastic cover. 6. Reinsert screw holding the latch. 7. Reinstall plastic cover using two screws removed in Step 1. 8. Use the down arrow button on the remote control (J) to tilt down the display. Th
Summary of the content on the page No. 13
Installation Instructions Adjusting Upright Position of Display (Optional) 7 1. Adjust upright position of display (+/- 2°) by turning the bottom screw on the motorized bracket (A). (A) 1 13
Summary of the content on the page No. 14
Installation Instructions Setting Preset Position 8 1. Remove pin (C1) from STORE opening. 2. Insert pin into appropriate opening dependent on tilt angle desired: Insert pin into "P1" for maximum preset tilt angle of approximately 6°. Insert pin into "P2" for maximum preset tilt angle of approximately 9°. Insert pin into "STORE" for full tilt angle of 13°. Insert pin into "UP" to lock the display in the up position (approximately 5°). UP P2 P1 STORE UP P2 P1 STORE C1 1 14
Summary of the content on the page No. 15
Installation Instructions 15
Summary of the content on the page No. 16
Installation Instructions USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378 P 800.582.6480 / 952.894.6280 F 877.894.6918 / 952.894.6918 Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands P +31 (0)40 2668620 F +31 (0)40 2668615 Chief Manufacturing, a division of Asia Pacific A Room 24F, Block D, Lily YinDu International Building Milestone AV Technologies LuoGang, BuJi Town, Shenzhen, CHINA. 8820-000037 P +86-755-8996 9226 2008 Milestone AV Technologies F +86-755-8996 9217 www
