Summary of the content on the page No. 1
3-216-226-12(1)
Network Video Receiver
Operating Instructions
DMX-NV1
© 2007 Sony Corporation
Summary of the content on the page No. 2
Owner’s Record The model and serial numbers are located at the bottom of the receiver. Record these numbers in the spaces provided below. Refer to them whenever you call upon your Sony dealer regarding this product. Model No. Serial No. For Your Convenience Please contact Sony directly if you: z Have questions on the use of your module after reading the Operating Instruction manual and Quick Setup Guide z Experience difficulty operating your module Contact Sony Customer Support at:
Summary of the content on the page No. 3
WARNING NOTIFICATION CAUTION To reduce the risk of fire or electric shock, do This equipment has been tested and found to Do not attempt to modify this product in any not expose this receiver to rain or moisture. comply with the limits for a Class B digital way without written authorization from Sony device, pursuant to Part 15 of the FCC Rules. Electronics, Inc. Unauthorized modification These limits are designed to provide reasonable could void the user's authority to operate this protecti
Summary of the content on the page No. 4
USE Important AC power cord and other cables If you damage the AC power cord or other cables, it may result in a fire or an electric shock. If the AC power cord or other cables is damaged, stop Safety using it at once and contact the Sony service center. s Do not place the receiver where the power cord and cables are subject to wear or abuse. s Do not pinch, bend, or twist the cord excessively. The core lines may Instructions be bared and cut, and cause a short-circuit, resulting in a fire
Summary of the content on the page No. 5
VENTILATION The holes on the side of the receiver are provided for necessary ventilation. To ensure reliable operation of the receiver, and to protect it from overheating, these ventilation holes must never be blocked or covered. Unless proper ventilation is provided, the receiver may gather dust and get dirty. For proper ventilation, observe the following: s Never block the ventilation holes by placing the receiver on a bed, sofa, rug or other similar surface. s Never place the receiver in
Summary of the content on the page No. 6
Summary of the content on the page No. 7
Contents Getting Started TM Welcome to the World of ..........................................................................9 A Snapshot of the BRAVIA Internet Video Link ............................................................9 LED Indicators...........................................................................................................10 Setting up the BRAVIA Internet Video Link .................................................................11 Cable Connections..............
Summary of the content on the page No. 8
Summary of the content on the page No. 9
Getting Started Getting Started TM Welcome to the World of Thank you for purchasing this Sony BRAVIA Internet Video Link receiver. This manual is for model DMX-NV1. The packing box contains accessories that are listed on page 51. For optimum picture performance, your BRAVIA TV with XMB TM ® x (XrossMediaBar ) and DMe interface is capable of receiving high definition programming through your high-speed Internet connection. (Broadband Internet connection of at least 10 Mbps recommended for
Summary of the content on the page No. 10
Getting Started LED Indicators Power LED Indicators Green The receiver is powered on. Orange (Blinking) The receiver is installing new software (do not disconnect AC power). Red (Blinking) Unable to connect to TV. Check cable connections. Network LED Indicators Green The receiver is connected to the home network. Green (Blinking) The receiver has network activity. Power LED 1 1 Network LED NETWORK NETWORK Make sure your home network is connected to the Internet. Check the Troubleshooting secti
Summary of the content on the page No. 11
Getting Started Getting Started Setting up the BRAVIA Internet Video Link Perform the following simple tasks to setup your receiver: make the cable connections, connect to the Internet, and attach the receiver to your TV. Be sure to turn off your TV before making any cable connections. The receiver is packaged with the Cable Cover attached. Begin by removing Refer to the section the Cable Cover as shown below. Attaching the Receiver to Your TV on page 20 for attachment instructions. Front
Summary of the content on the page No. 12
Getting Started Cable Connections 1 Connect the four cables to your receiver in the order shown below. LAN DC IN 9V OUT B A Connect the AC adapter to the DC IN 9V port on the receiver. Do not plug into the wall outlet at this time. x B Connect the small (mini B) end of the USB cable to the DMe port on the receiver. C Connect one end of an Ethernet cable (not supplied) to the LAN Ethernet port on the receiver. D Connect the L-shaped end of the HDMI cable to the HDMI OUT port on the r
Summary of the content on the page No. 13
Getting Started Getting Started Connect to the There are several ways to connect your receiver to the Internet. Find your connection method in the list below and proceed to that step. Please read and Internet follow the directions carefully. Sony Recommended Option 1 Gaming Adapter as a Wireless Bridge Connection Connection Speed Option 2 Powerline Ethernet Adapter Connection Standard 2.5 Definition Video Mbps Option 3 Direct Router Connection High Definition 10 Video Mbps Option 1. Gaming
Summary of the content on the page No. 14
Existing Electrical Wiring Getting Started Option 2. Powerline Ethernet Adapter Connection Powerline Ethernet Adapter Ethernet Cable Router Requirements: Ethernet Cable, Powerline Ethernet Adapter 1 Plug in a Powerline Ethernet Adapter with an established Internet connection to the power outlet located closest to the receiver. 2 Connect an Ethernet cable between your receiver and the Powerline Ethernet Adapter. Be sure that a second Powerline Ethernet Adapter is connected to your modem. 3 P
Summary of the content on the page No. 15
Getting Started Getting Started Option 3. Direct to Router Connection Modem Requirements: Ethernet Cable, Router 1 Connect an Ethernet cable between your receiver and the router. Proceed to the section Confirm Connection below, to confirm the connection. Confirm Connection 1 Plug in the receiver. 2 Power on the TV. 3 Confirm the LED lights are green as shown below. Power LED 1 1 Network LED NETWORK NETWORK See LED Indicators on page 10 for a description of all LED indicator colors. 15
Summary of the content on the page No. 16
Getting Started Basic Remote Control Instruction 1 Press the HOME button on your TV’s remote control to access the XMB . TM 2 Press the V/v/B/b buttons to navigate. 3 Press the button to make selections. x 4 Press the DMe button to confirm your connection and to access My Page (see page 38). 16
Summary of the content on the page No. 17
Getting Started Getting Started Confirm Network Connection Follow these instructions to confirm that your Internet Video Link receiver is properly connected. x 1 Press the DMe button on your TV’s remote control to view the connection status. If “Feature available with DMeX module” appears on the screen, wait a few moments and try again. 2 When you see the message “Configuration Successful,” press the HOME button on your TV’s remote control. These menu icons associated with ® the receiver w
Summary of the content on the page No. 18
Getting Started Region Setup Complete Region setup to personalize My Page and fully enjoy your receiver. Region setup is optional but recommended 1 On the Settings menu, select Internet Video. 2 Select Region. 3 The default country is the United States. Press the V/v/B/b and 0-9 buttons to enter your ZIP code. 4 Press the B button on your TV’s remote control to switch countries, if applicable. Highlight your country and press the button. You can find all the countries and cities available o
Summary of the content on the page No. 19
Getting Started Getting Started 5 If you select Canada, enter your postal code using your TV’s remote control. Press V/v buttons for letters, and 0-9 for numbers. If you select a country other than the United States or Canada, choose the city closest to you from the list provided (see the Country and City List on page 47). 19
Summary of the content on the page No. 20
Getting Started Attaching the Receiver to Your TV The attachment location of the receiver varies by TV model as shown below in illustrations A-F. Before you begin the attachment, slide the Cable Cover back into place. Make sure the notches on the Cable Cover align with those indicated on the receiver. Front of Receiver LAN DC IN 9V LAN DC IN 9V OUT OUT B Mounting to the Back of Your TV 1 Find the location where you will need to attach the receiver. The receiver can also be used as a stand-
