Summary of the content on the page No. 1
Owner's Manual
! WARNING !
Exercise can present a health
risk. Consult a physician
before beginning any exercise
program with this equipment.
If you feel faint or dizzy,
immediately discontinue use
of this equipment. Serious
bodily injury can occur if this
equipment is not assembled
and used correctly. Serious
bodily injury can also occur if
all instructions are not
followed. Keep others and
pets away from equipment
when in use. Always make
sure all bolts and nuts are
tightened prior
Summary of the content on the page No. 2
TABLE OF CONTENTS Page Page Safety Instructions 2 Maintenance Instructions 15 Before You Begin 4 Product Parts Drawing 16 Hardware Identification Chart 5 Parts List 17 Assembly Instructions 6 Warranty 19 Operational Instructions 11 Notes 20 Storage 15 Fax/Mail Ordering Form 22 SAFETY INSTRUCTIONS WARNING: To reduce the risk of serious injury, read the following safety instructions before using the Elite Inversion System. 1. Read all warnings posted on the Elite Inversion System. 2.
Summary of the content on the page No. 3
CALL US FIRST THANK YOU FOR PURCHASING THE Elite Inversion System To help you get started, we have pre-assembled most of your Elite Inversion System at the factory with the exception of those parts left unassembled for shipping purposes. Simply follow the few assembly instructions set forth in this manual. Within a few minutes you will be getting your body into shape and on your way to achieving a happier and healthier lifestyle. Should you have any questions, please call our Customer Ser
Summary of the content on the page No. 4
BEFORE YOU BEGIN Although Stamina tries to manufacture its products Thank you for choosing the Elite Inversion with the finest materials and uses the highest System. We take great pride in producing this standards of manufacturing, occasionally a part that quality product and hope it will provide many hours does not fit, is the incorrect size, or is otherwise of quality exercise to make you feel better, look better inappropriate is found. Even with the highest and enjoy life to its full
Summary of the content on the page No. 5
HARDWARE IDENTIFICATION CHART This chart is provided to help identify the hardware used in the assembly process. Place the washers, the end of the bolts, or screws on the circles to check for the correct diameter. Use the small scale to check the length of the bolts and screws. 3/16" 1/4" 5/16" 3/8" 1/2" INCHES 02 1/2 1 1/2 1/2 3 1/2 4 1/2 5 1/2 6 in. mm. 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 length MILLIMETERS 6 8 10 12 NOTICE: The length of all bolts and screws except those with
Summary of the content on the page No. 6
ASSEMBLY INSTRUCTIONS Place all parts from the box in a cleared area and position them on the floor in front of you. Remove all packing materials from your area and place them back into the box. Do not dispose of the packing materials until assembly is completed. Read each step carefully before beginning. If you are missing a part please call our toll-free number for assistance 1 (800) 375-7520 or e-mail us at : parts@staminaproducts.com STEP 1 Insert the LEFT and RIGHT REAR FRAMES(2, 3)
Summary of the content on the page No. 7
ASSEMBLY INSTRUCTIONS A B C STEP 3 Slide the bottom of the two PIVOT ARMS(91) into the brackets located at each side of the MAIN FRAME (92). Align the desired hole on the arm with the peg on the bracket, then insert the peg into the hole to lock the PIVOT ARMS(91) in position. Secure the PIVOT ARMS(91) with the SECURING KNOBS (3/8"-16 x 1/2")(93) on the inner side of the brackets. PIVOT ARM ADJUSTMENT: There are three adjustment holes on the PIVOT ARMS(91) allowing you to position the MAIN FRA
Summary of the content on the page No. 8
ASSEMBLY INSTRUCTIONS STEP 5 Attach the ANGLE ADJUSTMENT BARS(85) onto the shafts on both sides of the MAIN FRAME(92) with BOLTS(M8 x 15mm)(62) and WASHERS(M8)(69). Do not tighten the bolts until STEP 6. STEP 6 Slide one of the SUPPORT SLEEVES(84) onto the left ANGLE ADJUSTMENT BARS(85). Install the SUPPORT SLEEVES(84) onto the shaft on the LEFT FRAME(2) with the SUPPORT SLEEVE(84) above the shaft as shown in the illustration, and secure with a BOLT(M8 x 15mm)(62) and WASHER(M8) (69). Insert
Summary of the content on the page No. 9
ASSEMBLY INSTRUCTIONS STEP 7: Attach the FOOTREST(11) onto the HEIGHT ADJUSTMENT BEAM(10) with the adjustment holes facing down. Secure the FOOTREST(11) in place with the ADJUSTMENT KNOB(12). NOTE: The four adjustment holes in the FOOTREST(11) allow the FOOTREST(11) to be attached in four different positions. Start with one of the center positions and adjust if necessary. Use the outer position if users are taller than average. Use the inner position if users are shorter than average. STEP 8 I
Summary of the content on the page No. 10
ASSEMBLY INSTRUCTIONS STEP 10 Install the HEIGHT ADJUSTMENT BEAM(10) into MAIN FRAME(92) by pulling the SPRING PIN(35) on the MAIN FRAME(92) and inserting the HEIGHT ADJUSTMENT BEAM(10) as shown. For added safety, thread the LOCKING KNOB(3/8"-16 x 3/4")(36) into back side of the MAIN FRAME(92). WARNING: Do not use the Elite Inversion System until you have verified your height setting. Failure to use the proper height setting can result in difficulty recovering from the decline position. See HE
Summary of the content on the page No. 11
OPERATIONAL INSTRUCTIONS GENERAL PRECAUTIONS 1. Use the lowest holes in the PIVOT ARMS(91) until you become familiar with the Elite Inversion System. 2. Do not use the Elite Inversion System alone. Always have a helper available in case assistance is needed in recovering from the decline position. 3. Make sure that the FOAM PADS(18) and HEEL HOLDERS(15) are holding your feet securely. 4. Make sure that the HEIGHT ADJUSTMENT BEAM(10) is properly set for your height. 5. Make sure that the HEIGHT
Summary of the content on the page No. 12
OPERATIONAL INSTRUCTIONS INVERSION ANGLE ADJUSTMENT There are 11 adjustment holes in the ANGLE ADJUSTMENT BARS(85) allowing you restrict the movement of the NYLON BED(37) to different angles by inserting the PULL PINS(86) into different adjustment holes. The top holes will allow the least amount of inversion angle. The lowest hole will allow the greatest amount of inversion angle and the Elite Inversion System will go into the full inversion position. CAUTION: 1. Use the holes near the top in th
Summary of the content on the page No. 13
OPERATIONAL INSTRUCTIONS USING THE PRO INVERSION SYSTEM 1. Start by lying fully back on the bed with your hands at your side, or resting on your thighs. 2. Keeping your hands close to your body begin to raise your arms slowly allowing the table to rotate backward. Stop, or lower your arms to control the downward rotation of the table. 3. Raise your arms until they are over your head. At this point, the inversion table will be as far back as it can go. 4. As you get more comfortable with the us
Summary of the content on the page No. 14
OPERATIONAL INSTRUCTIONS SUGGESTIONS FOR USE 1. Begin slowly: invert with the least amount of inversion angle to begin with. Stay inverted only as long as you are comfortable. Return upright slowly. 2. Make gradual changes: increase the angle only if it is comfortable. Increase the angle only one adjustment hole at a time. Increase the time of use 1-2 minutes up to ten over a period of weeks. Add stretching and light exercise only after you are comfortable with inversion. 3. Watch your bo
Summary of the content on the page No. 15
STORAGE The Elite Inversion System is designed to fold for easy storage. You can store 1. your Elite Inversion System as illustrated. Please follow the following process: STEP 1: Loosen LOCKING KNOB(36) and pull out the SPRING PIN(35). Now, slide the HEIGHT ADJUSTMENT BEAM(10) into the MAIN FRAME(92) and lock in the lowest adjustment hole. Refer to illustration 1. STEP 2: Remove the PULL PINS(86) from the ANGLE ADJUSTMENT BARS(85). Swing the NYLON BED(37) down to about the same place as t
Summary of the content on the page No. 16
PRODUCT PARTS DRAWING BACK FRONT 16
Summary of the content on the page No. 17
PARTS LIST DIAGRAM# PART NAME QTY 1 Front Frame 1 2 Left Rear Frame 1 3 Right Rear Frame 1 4 Base Frame 1 5 Handrail 2 10 Height Adjustment Beam 1 11 Footrest 1 12 Adjustment Knob 1 13 Heel Holder Tube 1 14 Heel Holder Bracket 2 15 Heel Holder 2 16 Inner Pad Tube 1 17 Outer Pad Tube 1 18 Foam Pad 2 19 Left Lever Cover 1 20 Right Lever Cover 1 21 Rear Lever Cover 1 22 Corner cap 1 23 Lever 1 26 Claw Spacer 2 31 Spring 1 32 Butt
Summary of the content on the page No. 18
PARTS LIST DIAGRAM# PART NAME QTY 60 Bolt, Button Head (M6 x 1 x 47mm) 1 61 Bolt, Button Head (M6 x 1 x 55mm) 2 62 Bolt, Button Head (M8 x 1.25 x 15mm) 5 63 Bolt, Button Head (M8 x 1.25 x 50mm) 5 64 Bolt, Button Head (M8 x 1.25 x 55mm) 2 66 Nylock Nut (M6 x 1) 4 67 Nylock Nut (M8 x 1.25) 5 68 Washer (M6 x ø16 x 1.5mm Thick) 10 69 Washer (M8) 15 70 Arc Washer (M8) 2 71 Arc Washer (M6) 1 72 Warning Label 1 73 Combination Wrench 1 74 Allen Wrench (4mm) 1 75 A
Summary of the content on the page No. 19
LIMITED WARRANTY MODEL 55-1537C WARRANTY Stamina Products, Inc. warrants that this product will be free from defects in materials and workmanship under normal use, service and proper operation for a period of 90 days on the parts and 5 years on the frame from the date of the original purchase from an authorized retailer. THIS WARRANTY SHALL NOT APPLY TO ANY PRODUCT WHICH HAS BEEN SUBJECT TO COMMERCIAL USE, ABUSE, MISUSE, ALTERATION OF ANY TYPE OR CAUSE OR TO ANY DEFECT OR DAMAGE CAUSED BY REPAI
Summary of the content on the page No. 20
NOTES 20
