Graco D72 user manual

User manual for the device Graco D72

Device: Graco D72
Category: Stroller
Manufacturer: Graco
Size: 0.7 MB
Added : 5/19/2014
Number of pages: 34
Print the manual

Download

How to use this site?

Our goal is to provide you with a quick access to the content of the user manual for Graco D72. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Graco D72.

For your convenience

If looking through the Graco D72 user manual directly on this website is not convenient for you, there are two possible solutions:

  • Full Screen Viewing - to easily view the user manual (without downloading it to your computer), you can use full-screen viewing mode. To start viewing the user manual Graco D72 on full screen, use the button Fullscreen.
  • Downloading to your computer - You can also download the user manual Graco D72 to your computer and keep it in your files. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase.
Graco D72 User manual - Online PDF
Advertisement
« Page 1 of 34 »
Advertisement
Print version

Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual Graco D72 but the selected pages only. paper.

Summaries

Below you will find previews of the content of the user manuals presented on the following pages to Graco D72. If you want to quickly view the content of pages found on the following pages of the manual, you can use them.

Abstracts of contents
Summary of the content on the page No. 1

Instructions – Parts List
ACETAL, POLYPROPYLENE, AND PVDF
Husky1040 Air-Operated
Diaphragm Pumps
308443Z
Acetal Model Shown
120 psi (0.8 MPa, 8 bar) Maximum Fluid Working Pressure
120 psi (0.8 MPa, 8 bar) Maximum Air Input Pressure
*Model No. D71 Acetal Pumps ( certified)
*Model No. D81 Acetal Pumps, Remote ( certified)
*Model No. D72 Polypropylene Pumps
*Model No. D82 Polypropylene Pumps, Remote
*Model No. D75 PVDF Pumps
*Model No. D85

Summary of the content on the page No. 2

Table of Contents Symbols Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Warning Symbol Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 WARNING Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Service This symbol alerts you to

Summary of the content on the page No. 3

WARNING TOXIC FLUID HAZARD Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin, inhaled, or swallowed.  Know the specific hazards of the fluid you are using.  Store hazardous fluid in an approved container. Dispose of hazardous fluid according to all local, state and national guidelines.  Always wear protective eyewear, gloves, clothing and respirator as recommended by the fluid and solvent manufacturer.  Pipe and dispose of the exhaust air

Summary of the content on the page No. 4

Installation General Information Tightening Screws Before First Use  The Typical Installation shown in Fig. 2 is only a Before using the pump for the first time, check and guide for selecting and installing system compo- retorque all external fasteners. See Torque Se- nents. Contact your Graco distributor for assistance quence, page 30. After the first day of operation, in planning a system to suit your needs. retorque the fasteners. Although pump use varies, a general guideline is to retorq

Summary of the content on the page No. 5

Installation Grounding WARNING Ground all of this equipment: FIRE AND EXPLOSION HAZARD  Pump: Connect a ground wire and clamp as shown This pump must be grounded. Before in Fig. 1. Loosen the grounding screw (W). Insert operating the pump, ground the system one end of a 12 ga (1.5 mm) minimum ground wire as explained below. Also read the sec- (Y) behind the grounding screw and tighten the tion FIRE AND EXPLOSION HAZARD screw securely. Connect the clamp end of the on page 3. ground wire to a t

Summary of the content on the page No. 6

Installation Air Line b. Locate one bleed-type master air valve (B) WARNING close to the pump and use it to relieve trapped air. See the WARNING at left. Locate the other A bleed-type master air valve (B) is required in master air valve (E) upstream from all air line your system to relieve air trapped between this accessories and use it to isolate them during valve and the pump. Trapped air can cause the cleaning and repair. pump to cycle unexpectedly, which could result in serious injury, inclu

Summary of the content on the page No. 7

Installation Mountings Fluid Suction Line  If using a conductive (Acetal) pump, use conductive hoses (G). If using a non-conductive (polypropy- CAUTION lene or PVDF) pump, ground the fluid system. See The pump exhaust air may contain contaminants. Grounding on page 5. Ventilate to a remote area if the contaminants could affect your fluid supply. See Air Exhaust  The pump fluid inlet (R) is a 1” raised face flange. Ventilation on page 10. See Flange Connections on page 8.  If the fluid inlet

Summary of the content on the page No. 8

Installation Flange Connections The fluid inlet and outlet ports are 1” raised face 1. Place a lockwasher and a flat washer on each bolt. flanges. Connect 1” flanged plastic pipe to the pump Refer to Fig. 3. as follows. You will need:  Torque wrench 2. Align the holes in the gasket and the pipe flange with the holes in the pump flange.  Adjustable wrench  One 4.25” diameter, 1/8” thick PTFE gasket, with 3. Lubricate the threads of the four bolts. Install the four 0.62 diameter holes and a 1.1

Summary of the content on the page No. 9

Installation Changing the Orientation of the Fluid Inlet Fluid Pressure Relief Valve and Outlet Ports The pump is shipped with the fluid inlet (R) and outlet (S) ports facing the same direction. See Fig. 4. To CAUTION change the orientation of the inlet and/or outlet port: Some systems may require installation of a pres- sure relief valve at the pump outlet to prevent 1. Remove the screws (106 or 112) holding the inlet overpressurization and rupture of the pump or (102) and/or outlet (103) manif

Summary of the content on the page No. 10

Installation Air Exhaust Ventilation The air exhaust port is 3/4 npt(f). Do not restrict the air WARNING exhaust port. Excessive exhaust restriction can cause erratic pump operation. FIRE AND EXPLOSION HAZARD Be sure to read FIRE OR EXPLOSION To provide a remote exhaust: HAZARD and TOXIC FLUID HAZARD on page 3, before operating this pump. 1. Remove the muffler (P) from the pump air exhaust Be sure the system is properly ventilated port. for your type of installation. You must vent the exhaust to

Summary of the content on the page No. 11

Operation 1. Be sure the pump is properly grounded. Refer to Pressure Relief Procedure Grounding on page 5. WARNING 2. Check all fittings to be sure they are tight. Be sure PRESSURIZED EQUIPMENT HAZARD to use a compatible liquid thread sealant on all The equipment stays pressurized until pressure is male threads. Tighten the fluid inlet and outlet manually relieved. To reduce the risk of serious fittings securely. injury from pressurized fluid, accidental spray from the gun or splashing fluid, f

Summary of the content on the page No. 12

Operation NOTE: Leaving air pressure applied to the air motor for Operation of Remote Piloted Pumps extended periods when the pump is not running may shorten the diaphragm life. Using a 3–way solenoid 1. Follow preceding steps 1 through 7 of Starting valve to automatically relieve the pressure on the air and Adjusting Pump. motor when the metering cycle is complete prevents this from occurring. 2. Open air regulator (C). Pump Shutdown WARNING WARNING The pump may cycle once before the external s

Summary of the content on the page No. 13

Maintenance Lubrication Tightening Threaded Connections The air valve is designed to operate unlubricated, however if lubrication is desired, every 500 hours of Before each use, check all hoses for wear or damage, operation (or monthly) remove the hose from the pump and replace as necessary. Check to be sure all air inlet and add two drops of machine oil to the air threaded connections are tight and leak-free. Check inlet. fasteners. Tighten or retorque as necessary. Although pump use varies, a

Summary of the content on the page No. 14

Troubleshooting 1. Relieve the pressure before checking or servicing WARNING the equipment. To reduce the risk of serious injury whenever you are instructed to relieve pressure, always follow the 2. Check all possible problems and causes before Pressure Relief Procedure on page 11. disassembling the pump. PROBLEM CAUSE SOLUTION Pump cycles at stall or fails to hold Worn check valve balls (301), seats Replace. See page 18. pressure at stall. (201) or o-rings (202). Pump will not cycle, or cycles

Summary of the content on the page No. 15

Troubleshooting PROBLEM CAUSE SOLUTION Fluid in exhaust air. Diaphragm ruptured. Replace. See pages 19 to 21. Loose fluid side plate (105). Tighten or replace (pages 19 to 21). Pump exhausts excessive air at Worn air valve block (7), o-ring (6), Repair or replace. See pages stall. plate (8), pilot block (18), u-cups 16 to 17. (10), or pilot pin o-rings (17). Worn shaft seals (402). Replace. See pages 19 to 21. Pump leaks air externally. Air valve cover (2) or air valve cover Tighten screws. See

Summary of the content on the page No. 16

Service 7. Clean all parts and inspect for wear or damage. Repairing the Air Valve Replace as needed. Reassemble as explained on Tools Required page 17.  Torque wrench  Torx (T20) screwdriver or 7 mm (9/32”) socket 2 3 wrench 2  Needle-nose pliers 4  O-ring pick  Lithium base grease NOTE: Air Valve Repair Kits 236273 (aluminum center housing models) and 255061 (sst center housing models) are available. Refer to page 26. Parts included in the kit are marked with a symbol, for example (4)

Summary of the content on the page No. 17

Service Reassembly 1 Insert narrow end first. 1. If you removed the bearings (12, 15), install new 2 Grease. ones as explained on page 22. Reassemble the 3 fluid section. Install with lips facing narrow end of piston (11). 4 Insert wide end first. 2. On aluminum center housing models, install the valve plate seal (9) into the groove at the bottom 10 2 3 of the valve cavity. The rounded side of the seal must face down into the groove. See Fig. 10. 4 11 3. Install the valve plate (8) in the c

Summary of the content on the page No. 18

Service Reassembly Ball Check Valve Repair 1. Clean all parts and inspect for wear or damage. Tools Required Replace parts as needed.  Torque wrench 2. Reassemble in the reverse order, following all notes in Fig. 11. Assemble the ball checks exactly  10 mm socket wrench as shown. The arrows (A) on the fluid covers (101) must point toward the outlet manifold (103).  O-ring pick Torque to 80 to 90 in-lb (9 to 10 N-m). See Torque Se- 1 Disassembly quence, page 30. 2 Arrow (A) must point toward o

Summary of the content on the page No. 19

Service Disassembly Diaphragm Repair NOTE: A Fluid Section Repair Kit is available. Refer to page 25 to order the correct kit for your pump. Parts Tools Required included in the kit are marked with an asterisk, for example (401*). Use all the parts in the kit for the best  Torque wrench results. WARNING  10 mm socket wrench To reduce the risk of serious injury whenever you are instructed to relieve pressure, always follow the  19 mm open–end wrench Pressure Relief Procedure on page 11. 1. Rel

Summary of the content on the page No. 20

Service 4. Unscrew one outer plate (105) from the diaphragm Reassembly shaft (24). Remove one diaphragm (401), and the 1. Grease the shaft u-cup packings (402*) and install inner plate (104). See Fig. 13. them so the lips face out of the housing (1). See Fig. 13. 2. Grease the length and ends of the diaphragm shaft (24), and slide it through the housing (1). NOTE: PTFE models include a PTFE diaphragm (403) in addition to the backup diaphragm (401). 3. Assemble the inner diaphragm plates (104), d


Alternative user manuals
# User manual Category Download
1 Graco 1755545 User manual Stroller 266
2 Graco 1756483 User manual Stroller 54
3 Graco 1750713 User manual Stroller 34
4 Graco 1755755 User manual Stroller 23
5 Graco 1753039 User manual Stroller 34
6 Graco 1759207 User manual Stroller 4
7 Graco 1757083 User manual Stroller 2
8 Graco 1757816 User manual Stroller 7
9 Graco 1757978 User manual Stroller 1
10 Graco 1760752 User manual Stroller 4
11 Graco 1759724 User manual Stroller 2
12 Graco 1760815 User manual Stroller 8
13 Graco 1760818 User manual Stroller 34
14 Graco 1762856 User manual Stroller 5
15 Graco 1763442 User manual Stroller 1
16 Edelbrock 207-2 User manual Stroller 0
17 ABC Office FD 400E2 User manual Stroller 1
18 ABC Office FD 400P2 User manual Stroller 0
19 ABC Office FD 400P1 User manual Stroller 0
20 Agilent Technologies 87020 User manual Stroller 0