Summary of the content on the page No. 1
Xerox Wide Format Solutions
8855/721P Stacker
Operator Manual
THE DOCUMENT COMPANY
701P39432
XEROX
Summary of the content on the page No. 2
Prepared by: Global Knowledge and Languages Services 780 Salt Road Webster, New York 14580 Copyright© 2003 by Xerox Corporation. Allrights reserved. XEROX and all product names and number names are trademarks of XEROX CORPORATION. Other company trademarks are also acknowledged. Printed in U.S.A. 701P39412 5/2003
Summary of the content on the page No. 3
Table of Contents It’s Illegal ..................................................................... 2 FCC Compliance ......................................................... 2 Introduction to your Stacker ...................................... 3 Safety Notes ................................................................ 4 Identifying the Parts on the Stacker .......................... 6 Location of the Stacker Serial Number ...................... 7 Stacker Operation ..................
Summary of the content on the page No. 4
2 It’s Illegal FCC Compliance In the USA In the USA It is against U.S. law to copy copyrighted material without permission Class A of the copyright owner unless the copying falls within the “Fair Use” This equipment has been tested and found to comply with the limits library reproduction rights of the copyright law. for a Class A digital device, pursuant to Part 15 of the FCC rules. Further information on these U.S. provisions may be obtained from These limits are designed to provide reasonabl
Summary of the content on the page No. 5
FOR SERVICE:1-800-822-2979 Introduction to Your Stacker A Customer Service Support Representative will assist you in Congratulations on acquiring your new Stacker. keeping your stacker operational and, if required, will arrange for a This User Guide provides information that is needed to operate the Customer Service Engineer to visit your stacker and restore its Stacker. performance. The information below is needed when you call your Xerox support PURCHASE OF OTHER EQUIPMENT: experts. Call a loc
Summary of the content on the page No. 6
4 Safety Notes Your stacker has been designed and tested to meet strict safety requirements. These include safety agency examination and approval, and compliance to established environmental standards. Please read the following instructions carefully before operating the Stacker. NOTE: Refer to Instructions as needed to ensure the continued safe operation of your stacker. FOLLOW all warnings and instructions marked on or supplied with the product. UNPLUG the stacker from the wall outlet befor
Summary of the content on the page No. 7
Safety Notes (continued) UNPLUG this stacker from the wall outlet and refer servicing to qualified service personnel under the following conditions: When the power cord is damaged or frayed. If liquid has been spilled into the product. If the stacker has been exposed to rain or water. If the stacker is producing unusual noises or odors. If the stacker has fallen or the cabinet has been damaged. The safety feature has been activated for a second time. The stacker still does not wor
Summary of the content on the page No. 8
6 Identifying the Parts on the Stacker Upper Panel Assembly Inlet Power Switch Power Indicator Stacker Unit Light Printed Wiring Board (Transmission) Media Supports Release Handle Printed Wiring Board Release Handle Frame Assembly (Reception) Thumb Screws
Summary of the content on the page No. 9
Location of the Stacker Serial Number Stacker Jam Clearance In order to locate the serial number of your stacker, you must first The paper fed from the printer will be either cut or uncut. push down the release lever and slide the stacker away from the Caution printer. To ensure the safety of the user, be aware during jam The serial number plate is located on the left of the front cover facing clearance that the surface will be hot. the printer. Cut In order to clear a jam in the stacker, lift
Summary of the content on the page No. 10
8 Top View Stacker Relocation The stacker cannot be moved except by a DRC rigger. Stacker power cord 12' 66" To ensure that the stacker operates reliably after moving it to a new (168cm) location, consider the following guidelines: Printer Stacker power cord The new location must provide minimum clearances around the 12' stacker. These clearances are shown in the diagram on the (3.66m) 153.5” right. (390cm) The flooring in the new location must be adequate to support the 39.5" 721P wei
Summary of the content on the page No. 11
Technical Data Dimensions: Width: 34” (864mm) 57.5” (1461mm) w/paper supports extended. Depth: 41” (1041mm) Height: 28.5” (724mm) Weight: 108 lbs. (49kg) Paper Size: 36 x 48” (914mm x 1219mm) Max. Stacker Capacity: 200 sheets of plain paper with minimal scatter 500 plain paper sheets Max. Electrical Data: Current service: 3 Amps or more Power Supply: 110V - 240V Frequency: 50/60Hz Power Consumption: 60W Temperature: 50F - 90F (10C - 32C) Humidity: 20 - 85% Noise Level: 57dB Max
