Summary of the content on the page No. 1
TABLE OF CONTENTS
INTRODUCTION 3
PRODUCT OVERVIEW 4
BEFORE YOU BEGIN 8
BATTERY INSTALLATION 9
LOW BATTERY WARNING 10
GETTING STARTED 10
PLACEMENT OF THE UNITS 11
REMOTE AND INDOOR TEMPERATURE 11
MAXIMUM AND MINIMUM READINGS 11
LOST COMMUNICATION 12
TRANSMISSION COLLISION 13
WWVB RADIO CONTROLLED TIME 13
ATOMIC CLOCK 14
TIME AND CALENDAR DISPLAY MODES 14
Honeywell
MANUAL SETTINGS 15
Wireless In/Out Thermometer
CLOCK ALARMS 15
SNOOZE 17
BACKLIGHT 17
Summary of the content on the page No. 2
INTRODUCTION PRODUCT OVERVIEW Thank you for selecting the Honeywell Wireless In/Out Thermometer. This MAIN UNIT device combines precise time keeping with monitoring and displaying the FEATURES weather conditions from up to three remote locations. • Time automatically sets to the US Atomic Clock In this package you will find: • 12 or 24 hours Time Format • One main unit (receiver) • Dual crescendo Time Alarm with Snooze • One remote sensor (transmitter) TS13C • Day of the week displaye
Summary of the content on the page No. 3
FRONT/REAR VIEW B. SNOOZE/LIGHT button • Stops the clock’s alarm temporarily I • Activates a backlight for 5 seconds B C. CHANNEL button • Recalls a different remote sensor reading – 1,2 or 3 • Activates the remote channels search A D. UP ( ▲) button • Increases the parameters • Activates US Time Zone selection mode • Activates manual search for atomic time signal H • Enables time alarms (W) and (S) and Ice Warning Alarm C E. MODE button G • Toggles between time modes - time
Summary of the content on the page No. 4
I. WALL- MOUNT RECESSED OPENING C. RESET • Keeps the unit on the wall • Resets all previous settings J. BATTERY COMPARTMENT D. CHANNEL SWITCH • Accommodates 2 (two) UM-3 or AA 1.5V alkaline batteries • Selects the desired channel -1, 2 or 3 K. REMOVABLE TABLE STAND E. WALL-MOUNT RECESSED OPENING • Holds unit in upright position on a flat surface • Keeps the remote sensor on the wall F. °C/ °F SWITCH • Selects the temperature display in Celsius or Fahrenheit REMOTE SENSOR FEATURES •
Summary of the content on the page No. 5
you intend measuring outdoor elements, place remote sensor outdoors • Replace the battery compartment door and secure the screws. • The main unit must be placed indoors. • Secure the remote sensor in the desired location. NOTE: 1. Avoid pressing any buttons on the main unit before the remote readings MAIN UNIT are displayed. • Remove the battery compartment door. 2. The effective operating range may be influenced by the surrounding building • Install 2 batteries (UM-3 or “AA” size 1.5V
Summary of the content on the page No. 6
temperature and humidity display. PLACEMENT OF THE UNITS The main unit can be placed on any flat surface indoors. The remote sensor To clear the memory, press and hold MEM (memory) button for two seconds can be placed indoors or outdoors, on a flat surface or mounted on the wall. and all previously stored readings will be erased. REMOTE AND INDOOR TEMPERATURE LOST COMMUNICATION The remote temperature information line is located on the top line of the main If the main unit display line
Summary of the content on the page No. 7
TRANSMISSION COLLISION ATOMIC CLOCK Signals from the other household devices such as wireless doorbells, home Immediately after establishing communication between the main unit and security systems, and entry control, may interfere with this product or cause remote sensor, the atomic time signal receiver will open and start to search for temporary reception interruption. This is normal and will not affect the general the atomic time signal. The search usually takes between 5-8 minutes. p
Summary of the content on the page No. 8
subsequent days MANUAL SETTINGS It is necessary to set the desired US TIME ZONE. • If Ice Warning Alarm ( PRE-AL) is activated, in will sound at the set TIME ZONE time and alarm icon will flash once the remote temperature for Channel One (1) will reach 32°F(0°C) and below • Press MODE button once so that the Day of the Week abbreviation is displayed to the right of the time; for example: pm 2:37tu NOTE: Ice Warning Alarm can be set only if one or both - Weekday or • Select the Time Zone
Summary of the content on the page No. 9
30 will flash, meaning that if selected, the alarm will sound 30 minutes PRECAUTIONS earlier than the Weekday or Single alarm. This product is engineered to give you years of satisfactory service if handled carefully. Here are a few precautions: • Select the desired Ice Warning Alarm interval in 15 minutes increments between 15 and 90 minutes, using UP ( ▲) or DOWN ( ▼)buttons • Do not immerse the units in water. • Press ALARM ON/OFF button to confirm and exit from the alarm • Do not clea
Summary of the content on the page No. 10
TROUBLESHOOTING SPECIFICATIONS Check here before contacting customer service. Main Unit Indoor Temperature Proposed operating range: 23.0°F to 122.0°F (-5°C to +50°C) Issue Symptom Solution Temperature resolution: 0.2°F (0.1°C) Main unit US Atomic Time Place unit by the window and User-selectable (°F or °C) temperature display Maximum number of remote sensors: 3 (one included) signal is not received keep it there overnight RF range: Maximum 100 feet (30 meters) Remote sensor Can
Summary of the content on the page No. 11
FCC STATEMENT DECLARATION OF CONFORMITY This device complies with Part 15 of the FCC Rules. Operation is subject to the We following two conditions: (1) This device may not cause harmful interference, Name: Hideki Electronics, Inc. and (2) This device must accept any interference received, including Address: 7865 SW Mohawk interference that may cause undesired operation. Tualatin, OR 97062 Warning: Changes or modification to this unit not expressly approved by the declare that the
Summary of the content on the page No. 12
STANDARD WARRANTY INFORMATION This product is warranted from manufacturing defects for one year from date of retail purchase. It does not cover damages or wear resulting from accident, misuse, abuse, commercial use, or unauthorized adjustment and repair. Note that online product registration is required to ensure valid warranty protection. To register your product, go to our Company website at: www.honeywellweatherstations.com. Click Online Product Registration under the Customer Service
