Summary of the content on the page No. 1
OPTIONAL ACCESSORIES
22222
11
111
R
SHREDDER KIT
P/N 890209. Shreds
leaves, dramatically reducing
total volume.
HOSE KITS
For vacuuming in hard to
reach areas.
Heavy Duty Vacuum
Hose Kit P/N 900943.
4"(102mm) x 10' (3.05m)
Homeowners Vacuum Hose
Kit P/N 900942.
4"(102mm) x 10' (3.05m)
NOZZLE WEAR PLATES
P/N 890413. Extends nozzle
life when used along curbs and
hard surfaces.
STANDARD TURF QUICK
DEBRIS BAG
P/N 890307. Standard on TKD
models. For use in leaves and
grass in non-dusty conditions.
Summary of the content on the page No. 2
55555 IN THE INTEREST OF SAFETY BEFORE STARTING ENGINE, READ AND UNDERSTAND THE “ENTIRE OPERATOR'S MANUAL & EN- GINE MANUAL.” THIS SYMBOL MEANS WARNING OR CAUTION. DEATH, PERSONAL INJURY AND/OR PROPERTY DAMAGE MAY OCCUR UNLESS INSTRUCTIONS ARE FOLLOWED CAREFULLY. WARNING: The Engine Exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. 21. DO NOT touch hot muffler, cylinder, or 13. DO NOT tamper with governor spri
Summary of the content on the page No. 3
99999 GENERAL SAFETY For your safety and the safety of others, these directions should be followed: Do not operate this machine without first reading ·DO NOT operate during excessive vibration. owner's manual and engine manufacturer's manual. ·DO NOT remove bag until engine has been turned off and has Use of Ear Protection is recommended while come to a complete stop. operating this machine. ·DO NOT remove hose kit cap on nozzle until engine has been turned off and has come to a complete stop.
Summary of the content on the page No. 4
LITERATURE ASSY P/N 890423 13 13 13 13 13 CONTROLS 12 Owner's Literature Check- Throttle Manual list Control Check Owner's Manual 890424 Start position STOP SLOW Literature Check Literature Briggs KD / TKD KD / TKD engines have Accessories Accessories a primer 890409 button carburetor with no choke. FAST Check Warranty Warranty Card Card 400972 Stop position Check EU Declaration of EU Declaration Conformity & EU of Conformity Distributor List & EU 890393 Distributor List 14 14 14 14 14 15 15 1
Summary of the content on the page No. 5
" 16 Operation INTENDED USE: This machine is designed for vacuuming CHIPPING OPERATION 16.7 16.7 16.7 16.7 16.7 leaves, grass clippings and other types of organic litter and (TKD MODLES ONLY) for chipping brush, limbs, corn and sunflower stalks and palm fronds. Debris mixed with cans, bottles and small amounts of sand Wearing Eye Protection and Durable can be vacuumed; however, it is not this machine's primary Gloves is recommended while operating purpose. Vacuuming cans, bottles and sand will
Summary of the content on the page No. 6
16 16 OPERATION continued 16 16 16 16. 16. 16. 16. 16.33333 DEBRIS BAG Debris bags are normal replaceable wear items. Note: Frequently empty debris to prevent bag overloading with more weight than you can lift. An optional bag and dust cover is available for use where debris will be vacuumed in dusty conditions (see Optional Accessories shown on page 1). DO NOT place bag on or near hot surface, such as engine. Run engine at 1/2 throttle for first 1/2 hour to condition new bag. Your
Summary of the content on the page No. 7
OPERATION continued 16 16 16 16 16 16.4 16.4 16.4 16.4 16.4 HANDLING & TRANSPORTING: 16. 16. 16.12 12 12 TAMPER-TKD ONLY 16. 16.12 12 Before turning machine off, use the Tamper to slowly push Using two people to lift machine is recommended. Lift holding the remaining pieces of wood through the chipper. This can handle and front of nozzle. Secure in place during transport. prevent any remaining wood from jamming in the chipper when machine is turned off. Do not leave tamper on the ground, sto
Summary of the content on the page No. 8
17 MAINTENANCE CHIPPER BLADE REMOVAL AND SHARPENING-TKD ONLY Use only a qualified mechanic for any adjustments, disassembly or any Chipper blades are normal replaceable wear items. kind of repair . DANGER DANGER KEEP KEEP HANDS and FEET HANDS and FEET A AW WA AY Y DANGER Chipper blade is sharp. Replace any damaged blade. WARNING: TO AVOID PERSONAL INJURY, ALWAYS TURN MACHINE OFF, MAKE SURE ALL MOVING Depending on the type and amount of wood being chipped, the PARTS COME TO A COMPLETE STOP. c
Summary of the content on the page No. 9
17 MAINTENANCE continued 17.3 17.1 IMPELLER REMOVAL continued DRIVE Chains are normal replaceable wear items. A new chain 18. If chipper blade properly clears anvil surface, proceed to step . If should not be used on worn sprockets. Sprockets should be not, return to (step 14) and add or subtract shim washers as replaced when replacing chains. needed to obtain a correct gap. Stop engine and disconnect spark plug 19. Reinstall engine and impeller onto housing in reverse order wire before
Summary of the content on the page No. 10
18 18 18 18 18 PARTS DRAWING R KD510SP, TKD510SP Part No. 890424 Form No. F011398A Page 10 of 12
Summary of the content on the page No. 11
ITEM KD510SP TKD510SP 19 NO. Description Part No. Qty. Part No. Qty. 1 Debris Bag Turf (service) 890305 1 890307 1 2 Throttle Assembly (INCL. 1 ea. 4,10) 900514-04 1 900514-04 1 3 Tamper - - 890229 1 4 Nut Lock (1/4 - 20) *8160001 8 *8160001 8 * Denotes 5 Screw Cap (1/4 - 20 x 1- 1/2 HEX) *8041008 6 *8041008 6 standard 6 Handle Assy' (incl. items 4(6), 5(4), 11(2), 75(2), 76 & 99) 900057 1 900059 1 hardware 7 Axle Rear - Frame W.A. 890389 1 890389 1 item that 8 Screw Handle 5/16 - 18 x 2-1/4
Summary of the content on the page No. 12
Item KD510SP Part TKD510SP Part No. Description No. Qty. No. Qty. 86 Wheel With Sprocket Ass'y Cast ( 21, 94, 95, 96) 890242 2 890242 2 87 Chain 52 Pitch 890239 2 890239 2 19 88 Chain 40 Pitch 900323 1 900323 1 89 Washer Flat 5/16 (3/8 ID x 7/8 x 1 1/6) *8171003 4 *8171003 4 PARTS LIST 90 Bolt Carriage 5/16 - 18 x 3/4 *8024039 4 *8024039 4 91 Washer Spring Lock 5/16 *8177011 4 *8177011 4 92 Nut Regular 5/16 - 18 *8142002 4 *8142002 4 ( Continued from 93 Jackshaft 900320 1 900320 1 page 11 )
