Grizzly H6144 user manual

User manual for the device Grizzly H6144

Device: Grizzly H6144
Category: Nail Gun
Manufacturer: Grizzly
Size: 1.16 MB
Added : 12/2/2013
Number of pages: 20
Print the manual

Download

How to use this site?

Our goal is to provide you with a quick access to the content of the user manual for Grizzly H6144. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Grizzly H6144.

For your convenience

If looking through the Grizzly H6144 user manual directly on this website is not convenient for you, there are two possible solutions:

  • Full Screen Viewing - to easily view the user manual (without downloading it to your computer), you can use full-screen viewing mode. To start viewing the user manual Grizzly H6144 on full screen, use the button Fullscreen.
  • Downloading to your computer - You can also download the user manual Grizzly H6144 to your computer and keep it in your files. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase.
Grizzly H6144 User manual - Online PDF
Advertisement
« Page 1 of 20 »
Advertisement
Print version

Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual Grizzly H6144 but the selected pages only. paper.

Summaries

Below you will find previews of the content of the user manuals presented on the following pages to Grizzly H6144. If you want to quickly view the content of pages found on the following pages of the manual, you can use them.

Abstracts of contents
Summary of the content on the page No. 1

34º ANGLE FINISH NAILER - 2½"
MODEL H6144
INSTRUCTION MANUAL
COPYRIGHT © FEBRUARY, 2005 BY GRIZZLY INDUSTRIAL, INC., REVISED DECEMBER, 2007 (TS)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#BL6904 PRINTED IN CHINA

Summary of the content on the page No. 2

SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazard- ous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures. Indic

Summary of the content on the page No. 3

6. ONLY ALLOW TRAINED AND 13. ALWAYS DISCONNECT FROM PROPERLY SUPERVISED PER- POWER SOURCE BEFORE SONNEL TO OPERATE MACHIN- SERVICING MACHINERY. Make ERY. Make sure operation instruc- sure switch is in OFF position tions are safe and clearly under- before reconnecting. stood. 14. MAINTAIN MACHINERY WITH 7. KEEP CHILDREN AND VISITORS CARE. Keep blades sharp and AWAY. Keep all children and visi- clean for best and safest per- tors a safe distance from the work formance. Follow instruction

Summary of the content on the page No. 4

Additional Safety Instructions for Nailers 1. HAND INJURIES: Do not place your 5. HOSE USAGE: Make sure your hands near the nail point of entry. A air hose is designed for the tool nail can deflect and tear through the in use, is in good condition, and surface of the workpiece, puncturing is long enough to reach your work your hand or fingers. without stretching. However, an overly long air hose in the work area may be a tripping hazard. 2. COMBUSTIBLE GASES: Never connect the nailer t

Summary of the content on the page No. 5

Operating this nailer can propel Never point this nailer at yourself or objects into the air, causing imme- another person! Always pay attention diate eye damage. To protect your- to the direction this nailer is pointed. self, always wear American National Use this tool with respect and caution Standards Institute (ANSI) approved to lessen the possibility of operator or safety glasses or goggles when oper- bystander injury. Ignoring this warning ating this equipment. In addition, this

Summary of the content on the page No. 6

INTRODUCTION Foreword Contact Info We are proud to offer the Grizzly Model If you have any comments regarding this H6144 34º Angle Finish Nailer–2½". This manual, please write to us at the following model is part of a growing Grizzly family of address: fine pneumatic tools. When used accord- ing to the guidelines set forth in this man- Grizzly Industrial, Inc. ual, you can expect years of trouble-free, C/O Technical Documentation enjoyable operation and proof of Grizzly’s P.O. Box 2069 commi

Summary of the content on the page No. 7

SET UP Unpacking Inventory Your Model H6144 left our warehouse in After you remove the nailer case from the a carefully packed box. If you discover box you should find the following. the nailer is damaged after you have signed for delivery, please immediately Model H6144 Inventory (Figure 1) call Customer Service at (570) 546-9663 for advice. A. 34° Finish Nailer−2½ ......................... 1 B. Safety Goggles ................................. 1 Save the containers and all packing mat

Summary of the content on the page No. 8

Compressed Air System The Model H6144 is designed to be oper- ated at 60-100 PSI using clean, dry, regu- lated, compressed air. DO NOT exceed the maximum operating pressure for your model. Before using your new nailer, install a 1 ⁄4" NPT male quick connect fitting (not Exceeding the maximum permissible included) on the nailer and a matching 1 operating pressure may cause the ⁄4" NPT female fitting (not included) on nailer to explode, blowing metal frag- the air hose. Regulate the air

Summary of the content on the page No. 9

5. Without pressing the trigger, depress Safety Yoke the safety yoke mechanism against a scrap piece of wood that is clean and free of any knots, nails, or other foreign A safety yoke mechanism on the nose objects. of the nailer acts as a secondary safety device. When the trigger is pressed, the — If the nailer does not fire, then the nailer will not fire until the safety yoke safety yoke mechanism is working mechanism is depressed. correctly. Before you use your nailer for the first

Summary of the content on the page No. 10

OPERATIONS 4. Pull the magazine pusher all the way Loading back, then let it come forward until it rests against the end of the nail stick. When replacing nails in your Model H6144, follow these guidelines: Operating Gauge: 15 1 1 Length: 1 ⁄4" -2 ⁄2" Capacity: 40 If you have not read the safety instruc- Angle: 34° tions in this manual, do not operate the nailer. NOTICE: A number of manufacturers' nails may fit the Model H6144. However, Before you operate your nailer, place one for best

Summary of the content on the page No. 11

Adjusting Depth The Model H6144 features a knurled adjustment knob (Figure 5) for setting the nail depth into the workpiece. Figure 4. Example of nail deflection. Besides damaging your workpiece, deflection can cause injury if your free hand is securing the workpiece in the location that the nail deflects. 5. Pull the trigger. If the nail drove into Figure 5. Depth adjustment knob. the wood far enough, continue with your intended operations. If the nail went too far or not far enoug

Summary of the content on the page No. 12

4. Depress the backstop (Figure 6) Clearing Jammed inside the magazine and slide the nail Nails stick out of the magazine. The most frequent situation with any type of nailer is a nail jam. A jammed nail must be cleared before using the nailer again. To clear a jammed nail from the dis- charge area on the Model H6144: Backstop 1. DISCONNECT NAILER FROM THE Finger Tab AIR SUPPLY! Figure 6. Finger tab and backstop. 5. Flip up the quick release latch located on top of the nailer nose assembl

Summary of the content on the page No. 13

7. The jammed nail should now be vis- 4. Remove the top cap. ible; remove it from the discharge area with needle nose pliers. 5. The top of the piston should now be visible inside the cylinder, which is 8. Replace the driver guide cover and housed in the head of the nailer. snap the quick release latch back into operating position. 6. Open the magazine. 7. Watch the discharge area and push the Replacing Pistons/ top of the piston with your finger. You will see the piston shaft slide down t

Summary of the content on the page No. 14

CLEANING & LUBRICATION Cleaning Lubricating Use a good solvent to clean the nose Special oil has been included with your assembly of the nailer. Always be sure new Grizzly nailer to help maintain its that the nailer is dry before using it useful life. Place two to six drops of oil again. in the nailer air inlet (as shown in Figure 9) before every use, or after two hours of Do not allow dust, chips, sand, etc. into continuous use. the air connectors or into the body of the nailer; th

Summary of the content on the page No. 15

H6144 PARTS BREAKDOWN -14- H6144 34° Angle Finish Nailer–2½" � �� �� �� � �� �� �� �� � �� � �� �� �� �� �� � �� �� �� �� �� �� �� �� �� � �� �� �� �� �� �� �� �� �� �� �� �� �� �� � �� �� �� �� �� �� �� �� � �� �� �� �� �� �� �� �� �� �� �� �� �� �� � �� �� �� �� �� �� �� �� �� �� �� �� �� � �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� ��

Summary of the content on the page No. 16

H6144 PARTS LIST REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PH6144001 SPECIAL CAP SCREW M5-.8 X 12 45 PH6144045 STEEL BALL 2MM 2 PH6144002 AIR DEFLECTOR 46 PH6144046 SAFETY SEAT 3 PH6144003 RUBBER WASHER 10 MM 47 PH6144047 DRIVE PIN 4 PSB38M CAP SCREW M5-.8 X 25 48 PR39M EXT RETAINING RING 8MM 5 PLW01M LOCK WASHER 5MM 49 PH6144049 DRIVE STAND 6 PH6144006 CYLINDER COVER 50 PH6144050 ADJUSTING NUT 7 PH6144007 COMPRESSION SPRING 51 PH6144051 COMPRESSION SPRING 8 PH6144008 SWITCH VALVE SEAT 52

Summary of the content on the page No. 17

TROUBLESHOOTING CAUSE PROBLEM ACTION Air leaking at trigger valve 1. O-rings in trigger valve 1. O-rings must be replaced housing are damaged. & operation of safety area. yoke must be checked. 1. Loose screws in housing. 1. Tighten screws. Air leaking between hous- ing and hose. 2. Damaged O-ring. 2. Replace O-ring. 3. Loose air fitting. 3. Tighten air fitting & use teflon tape. Air leaking between hous- 1. Damaged seal. 1. Replace damaged seals. ing and cap assembly. 1. Air leaks. 1. Tighten

Summary of the content on the page No. 18

WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty and any and all warranties that may be implied by law, including any merchantability or fitness, for any particular purpose, are hereby limited to

Summary of the content on the page No. 19

WARRANTY CARD Name _________________________________________________________________________ Street ________________________________________________________________________ City____________________State________Zip_________ Phone Number____________E-Mail___________________FAX ____________ Model # H6144 34°Angle Finish Nailer–2½" Serial#________________Order #____________ The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop better prod

Summary of the content on the page No. 20

Send a Grizzly Catalog to a friend: Name________________________________ Street________________________________ City______________State______Zip_______ FOLD ALONG DOTTED LINE Place Stamp Here GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE


Alternative user manuals
# User manual Category Download
1 Grizzly 16 Guage Finish Nailer H6143 User manual Nail Gun 0
2 Grizzly G1852 User manual Nail Gun 1
3 Grizzly 3-Piece Framing/Finish/Palm Nailer Kit H8232 User manual Nail Gun 0
4 Grizzly G1847 User manual Nail Gun 0
5 Grizzly G1861 User manual Nail Gun 0
6 Grizzly Air Palm Nailer H6141 User manual Nail Gun 0
7 Grizzly G3690 User manual Nail Gun 0
8 Grizzly G2420 User manual Nail Gun 0
9 Grizzly 28 clipped head framing nailer H6145 User manual Nail Gun 0
10 Grizzly G6047 User manual Nail Gun 0
11 Grizzly G6045 User manual Nail Gun 0
12 Grizzly 2-in-1 COMBINATION NAILER/STAPLER H7664 User manual Nail Gun 0
13 Grizzly G6046 User manual Nail Gun 0
14 Grizzly G3811 User manual Nail Gun 0
15 Grizzly G6049 User manual Nail Gun 0
16 Airfree Service Parts UF55 User manual Nail Gun 2
17 Airfree Service Parts UF55-RFK-500 User manual Nail Gun 2
18 Airfree Service Parts UF55w User manual Nail Gun 1
19 AllTrade AIR-PLUS 691164 User manual Nail Gun 0
20 AllTrade AIR-PLUS 691165 User manual Nail Gun 8