Summary of the content on the page No. 1
www.skylinkhome.com
Emergency Dialer
TM
DIAL-ALERT
MODEL: AD-103
If you would like to order Skylink’s products or have
difficulty getting them to work or download information
and user manual, please :
1. visit our FAQ section at www.skylinkhome.com, or
2. email us at support@skylinkhome.com, or
3. call our toll free at 1-800-304-1187 from Monday to
Friday, 9 am to 5 pm EST.
Fax (800) 286-1320
CUSTOMER SERVICE
17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3
Tel : (800) 304-1187
Fax : (800) 2
Summary of the content on the page No. 2
SKYLINK TECHNOLOGIES INC. Your Guide to the Emergency Dialer TM DIAL-ALERT MODEL: AD-103 The AD-103 Emergency Dialer contains all the above items. –2– –19– DIAL-ALERT QUICK GUIDE Factory Program # Functions Settings Default [PIN]+[PROG]+[1] Calling Time [1]-30, [2]-45, [3]-60, [4]-75, [5]-90 seconds 2 [PIN]+[PROG]+[2] Change Password Any 4-digit password 0000 [PIN]+[PROG]+[3] Voice Message Recording [0] - Main Message, [1-6] - Secondary Messages N/A [PIN]+[PROG]+[4] Phone Number [1-9] Up to 9 ph
Summary of the content on the page No. 3
BATTERY MAINTENANCE TABLE OF CONTENTS The AD-103 Dial-Alert comes with 1 battery that at some point you may PACKAGE CONTENTS............................................................................................4 have to replace: OVERVIEW.....................................................................................................5 INSTALLATION..............................................................................................................6-8 LIGHTS AND SOUNDS...........
Summary of the content on the page No. 4
PACKAGE CONTENTS ADVANCED PROGRAMMING All materials required for installation are included with this package 2. Enter [8], display now shows [P8 2], the most right digit represents the dial sequence. 3. To change the setting, enter either 1 or 2, where 1 is Dial Sequence 1, 1 Dial-Alert (AD-103) and 2 is Dial Sequence 2. 1 Telephone Line 4. If the new setting is accepted, it will emit 2 beeps. If you don’t hear 2 1 antenna (installed) beeps, that means the setting is not accepted, retry aga
Summary of the content on the page No. 5
ADVANCED PROGRAMMING OVERVIEW Erase Programmed Control Panel The AD-103 Dial-Alert can call multiple telephone numbers and sends a personalized pre-recorded message. The person receives the emergency You may erase the programmed control panel. If you have multiple control panels message can confirm receipt of that message by pressing the "#" key on programmed, you cannot erase a specific control panel, you must erase all their telephone. A pre-recorded message will be played notifying the person
Summary of the content on the page No. 6
INSTALLATION ADVANCED PROGRAMMING Changing Password The Dial-Alert is installed using the screws provided. We have also included double sided tape, to use for temporary installation while you are positioning Password is required for programming purposes. Factory default is 0000. the dialer. Once the dialer is positioned correctly, install it permanently with To change the setting, follow the instructions below. screws. We have also included wall anchors and a template to help position the screws
Summary of the content on the page No. 7
OPERATIONS INSTALLATION When the display shows “rEAdy”, that means the unit is in standby mode. 2. Thread the telephone line through the top It will dial when it receives a panic signal from the alarm panel, or its own hole in the back of the unit and plug it into panic button is pressed. the "LINE" jack. If you want to have an answering machine on the same line as It will dial the programmed phone numbers and playback the voice the dialer, thread the phone line through the message. bottom ho
Summary of the content on the page No. 8
STANDARD PROGRAMMING INSTALLATION To program additional phone numbers, follow the above procedures by Speaker On/Off Switch selecting a different phone number locations, from 1 to 9. The speaker must be on during pro- You may review a programmed phone number by following the same gramming and recording the voice procedures as programming a phone number. Simply press [ ] when the message in order to use the playback display shows the current setting instead of entering a new value allows you
Summary of the content on the page No. 9
STANDARD PROGRAMMING LIGHTS AND SOUNDS Below is an explanation of the lights and sounds of the Dial-Alert PROGRAM A PHONE NUMBER LIGHTS You may program up to 9 different phone numbers. Follow the instructions below to program phone numbers. ACPWR light on dialer is being powered by AC adapter. 1. Enter the current password (factory default password is 0000 ), then press ACPWR light off dialer is not receiving any AC power. [PROG], display will show [P] meaning you are now in programming mode. LO
Summary of the content on the page No. 10
STANDARD PROGRAMMING STANDARD PROGRAMMING There are a few programming steps you must perform before the dialer can 3. Enter [0] to [5] to select which message you would like to record. If you operate. Please follow the instructions below to program these fields, including: enter [3], you should see [P3 3 05]. - Record voice messages - Phone numbers you wish to dial during emergency (up to 9 phone numbers) Number Representing Message Type Max. Length (sec.) - Program the panic button or alarm p
