Summary of the content on the page No. 1
User's Manual
CADT-SA2 Series
Summary of the content on the page No. 2
Preface Copyright Please respect copyrighted content. Duplication or modification of this publication in whole or in part is prohibited without written authorization. Usage Strong impacts or dropping the product may cause damage. Allow only qualified personnel to repair this product. Disassembling or opening this product will void your warranty. Disclaimer Cavalry is not liable for compensation for data loss which may result from a malfunction of the product or from changes due to improper u
Summary of the content on the page No. 3
Thank you for choosing Cavalry. We at Cavalry extend our sincere gratitude for your purchase of this product. We hope our dedication to delivering high quality products with excellent customer service will ensure your continued interest in our products. This manual will assist in the operation of the product. To optimize your experience with this product, we recommend reading this entire manual before usage. Please keep this manual for future reference. 3 3
Summary of the content on the page No. 4
Table of Contents Preface .................................................................................................... 2 List of Accessories ............................................................................. 5 Product Illustrations ........................................................................... 6 Features ............................................................................................. 8 Setup Instructions ...............................................
Summary of the content on the page No. 5
List of Accessories 1. External power adapter / power cord (may vary with product) 2. SATA to eSATA adapter cable with bracket 4 3. eSATA cable 5 4. USB 2.0 cable 5. Resources CD 3 1 2 5 5
Summary of the content on the page No. 6
Front 1 1. LED status indicators 6 6
Summary of the content on the page No. 7
Back 2. Ventilation fan 3. 0-7 Settings Dial 4. Power switch 2 5. Power jack 6. eSATA port 6 7. USB 2.0 port 3 4 5 7 7 7
Summary of the content on the page No. 8
Features Plug-and-play for Mac OS v9.x and newer USB 2.0 and eSATA interface Pre-formatted in Mac OS X Extended Supports RAID levels 0, 1 and 0+1 Exceptional heat dissipating ability LED light indicators Nearly silent operation Designed for use with a Mac 8 8
Summary of the content on the page No. 9
Setup Instructions Follow the steps below to successfully set up your Cavalry External Hard Drive with your computer. Step 1. Start your computer and wait for the Mac OS to load completely. Step 2. Connect the power adapter to the drive. Then plug the power adapter into an electrical outlet. (Fig. 1) Step 3. Connect the square end of the USB cable to the hard drive. (Fig. 2) Then connect the flat end of the USB cable to the USB port on your computer. (Fig. 3) Fig. 1 9 9
Summary of the content on the page No. 10
SATA Users: If you do not already have an eSATA interface on your computer, first install the bracket when the computer is off. Then use the eSATA cable to connect the drive to the bracket. Turn on the unit then turn on the computer. (Please note that SATA is not required to use your product.) USB Cable Plug USB Port Fig. 2 Fig. 3 Step 4. Turn the power switch on. NOTE: Connect the USB cable to the drive before connecting the cable to the computer. To disconnect, remove the cable from the co
Summary of the content on the page No. 11
Step 5. Installing drivers for the Cavalry External Hard Drive. Mac OS This drive is preformatted to be plug-and-play for Mac OS 9.x and above. No formatting or drivers should be needed. Windows 2000/XP/Vista Requires reformatting to NTFS: go to the "Contents" folder of the Resources CD and follow the "Formatting Instructions" Guide. After that, your drive is plug-and-play: no device drivers or configuration required. The computer will detect the USB External Hard Drive as a new USB device
Summary of the content on the page No. 12
Windows 98/Me 1. Make sure Windows 98/Me is fully updated. Follow the "Formatting Instructions" PDF (in the "Contents" folder of the CD.) 2. Download drivers from www.cavalrystorage.com/su_download.htm Click on "Windows 98 Driver" to download file. Extract the file. 3. Navigate the device manager. 4. Right-click on the yellow question mark (unknown storage device). 5. When the device driver wizard starts, click on the "Browse" button to select the search directory to find drivers. 6. Find the
Summary of the content on the page No. 13
RAID Your product can be set up as RAID 1 (mirrored). "Mirrored" means that each of the two drives in your array store the same data, providing protection against the failure of one drive; however, when the drive appears on your computer, it will be recognized as a single hard drive. NOTE: Although the box indicates two hard drives are included, the total capacity in RAID 1 mode will not equal the sum of the two because the second drive is used as a "backup" of the first drive. (e.g. two 2
Summary of the content on the page No. 14
Change RAID Settings There are two ways to change the product settings. We recommend using the SteelVine software included with your drive; you may also use the "0-7 Settings Dial" (p17). Changing RAID settings erases any data on the drive. NOTE: Mac Users with OS v10.5 and newer proceed to page 17 for manual configuration of your RAID settings. For questions, please contact customer support by emailing customersupport@cavalrystorage.com. I. Using the SteelVine (GUI) software (In order to
Summary of the content on the page No. 15
Step 3. Follow the on-screen instructions to install the software. Step 4. After installation is completed, open the 57xx SteelVine Manager. Step 5. Once the program has loaded, go to Edit >> Configure Box. When prompted, enter the default password "admin." 14 15
Summary of the content on the page No. 16
Step 7. Select the setting that you prefer under "Storage Policy", then press "Apply." NOTE: Changing the settings will erase any data on the unit. Step 8. Your unit will take a few moments to start rebuilding. Once it has started, it may take several hours rebuild, depending on the setting you choose. You can monitor the progress in the SteelVine Manager main window. Keep the unit turned on and stationary while it rebuilds. The "HDD1" and "HDD2" lights will be lit during the rebuilding pr
Summary of the content on the page No. 17
II. Using the "0-7 Settings Dial" (For Mac OS 10.5 users or users who cannot use the SteelVine software) Step 1. Make sure the unit is off. Step 2. Refer to the following and identify the appropriate number of the setting you would like. Cavalry recommends RAID 1 for data protection: 0 SPANNING, drives are concatenated into one large volume 1 JBOD, drives show up individually 2 RAID 0 / Striped, single big volume, parallel access, fastest, no data redundancy 3 RAID 1 / Mirrored, 100% data red
Summary of the content on the page No. 18
Step 3. Turn the unit on its side and look into the hole with the numbers "0" to "7" printed around it (Figure 1). Inside the hole you should see a dial (Figure 2). Figure 1. 18 19
Summary of the content on the page No. 19
Step 4. Using a small, flathead screwdriver, turn the dial to the appropriate number of the setting you chose from Step 2. Once you have Figure 2. done this, lay the unit upright and set the unit where you would like it to be. Step 5. Turn the unit on. Step 6. Press the "Reset" or "Update" button located on the back of the product (Figure 1.) This will cause the unit to automatically "rebuild" into the new setting. The "HDD1" and "HDD2" indicator lights will flash while the unit is reb
Summary of the content on the page No. 20
III. Partitioning and formatting your RAID system These instructions are for users running Mac OS X (10.0+) and above. If you have another operating system, please refer to the Formatting Guide, found in the "Contents" folder of the Resources CD or online at www.cavalrystorage.com/su_download.htm Step 1. Go to the top menu and select ”Go”, “Applications”, “Utilities” and, then click on the “Disk Utility “ program. Step 2. The external drive will be listed on the left pane window. Click on
