Cypress CY7C63413C user manual

User manual for the device Cypress CY7C63413C

Device: Cypress CY7C63413C
Category: Computer Hardware
Manufacturer: Cypress
Size: 1.34 MB
Added : 6/27/2014
Number of pages: 32
Print the manual

Download

How to use this site?

Our goal is to provide you with a quick access to the content of the user manual for Cypress CY7C63413C. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Cypress CY7C63413C.

For your convenience

If looking through the Cypress CY7C63413C user manual directly on this website is not convenient for you, there are two possible solutions:

  • Full Screen Viewing - to easily view the user manual (without downloading it to your computer), you can use full-screen viewing mode. To start viewing the user manual Cypress CY7C63413C on full screen, use the button Fullscreen.
  • Downloading to your computer - You can also download the user manual Cypress CY7C63413C to your computer and keep it in your files. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase.
Cypress CY7C63413C User manual - Online PDF
Advertisement
« Page 1 of 32 »
Advertisement
Print version

Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual Cypress CY7C63413C but the selected pages only. paper.

Summaries

Below you will find previews of the content of the user manuals presented on the following pages to Cypress CY7C63413C. If you want to quickly view the content of pages found on the following pages of the manual, you can use them.

Abstracts of contents
Summary of the content on the page No. 1

CY7C63413C
CY7C63513C

CY7C63613C
Low-Speed High I/O, 1.5-Mbps USB Controller
• Operating voltage from 4.0V to 5.5V DC
Features
• Operating temperature from 0 to 70 degrees Celsius
• Low-cost solution for low-speed applications with high
• CY7C63413C available in 40-pin PDIP, 48-pin SSOP, 48-
I/O requirements such as keyboards, keyboards with
pin SSOP - Tape reel, all in Lead-Free versions for
integrated pointing device, gamepads, and many
production
others
• CY7C63513C available in 48-pin

Summary of the content on the page No. 2

CY7C63413C CY7C63513C CY7C63613C The sink current for each DAC I/O pin can be individually GPIO ports. The timer bits cause an interrupt (if enabled) when programmed to one of sixteen values using dedicated Isink the bit toggles from LOW “0” to HIGH “1.” The USB endpoints registers. DAC bits [1:0] can be used as high current outputs interrupt after either the USB host or the USB controller sends with a programmable sink current range of 3.2 to 16 mA a packet to the USB. The DAC ports have an ad

Summary of the content on the page No. 3

CY7C63413C CY7C63513C CY7C63613C . Pin Configuration Logic Block Diagram CY7C63513C CY7C63413C 6-MHz ceramic resonator 48-pin SSOP 48-pin SSOP D+ 1 48 V D+ 1 48 V CC CC 2 47 Vss 2 47 Vss D– D– OSC 3 46 P3[6] 3 46 P3[6] P3[7] P3[7] 4 P3[4] P3[5] 4 P3[4] P3[5] 45 45 P3[2] P3[2] P3[3] 5 44 12 MHz 6 MHz P3[3] 5 44 P3[0] 43 P3[0] P3[1] 6 43 P3[1] 6 P2[6] P2[6] P2[7] 7 42 P2[7] 7 42 P2[4] P2[4] P2[5] 8 41 P2[5] 8 41 P2[3] 9 40 P2[2] P2[3] 9 40 P2[2] 12-MHz USB USB D+ P2[1] 10 39 P2[0] P2[1] 10 39 P2[

Summary of the content on the page No. 4

CY7C63413C CY7C63513C CY7C63613C Pin Definitions CY7C63413C CY7C63513C CY7C63613C Name I/O 40-Pin 48-Pin Die 48-Pin 24-Pin Description D+, D– I/O 1,2 1,2 1,2 1,2 1,2 USB differential data; PS/2 clock and data signals P0[7:0] I/O 15,26,16 17,32,18 17,32,18, 17,32,18,31, 7, 18, 8, 17, 9, GPIO port 0 capable of sinking 7 mA 25,17,24 31,19,30 31,19,30, 19,30,20,29 16, 10, 15 (typical) 18,23 20,29 20,29 P1[3:0] I/O 11,30,12, 11,38,12, 11,38,12, 11,38,12,37, 5, 20, 6, 19 GPIO Port 1 capable of sink

Summary of the content on the page No. 5

CY7C63413C CY7C63513C CY7C63613C During an interrupt acknowledge, interrupts are disabled and Data the 14-bit program counter, carry flag, and zero flag are written The “Data” address mode refers to a data operand that is as two bytes of data memory. The first byte is stored in the actually a constant encoded in the instruction. As an example, memory addressed by the program stack pointer, then the consider the instruction that loads A with the constant 0xE8: PSP is incremented. The second byte

Summary of the content on the page No. 6

CY7C63413C CY7C63513C CY7C63613C Instruction Set Summary MNEMONIC operand opcode cycles MNEMONIC operand opcode cycles HALT 00 7 NOP 20 4 ADD A,expr data 01 4 INC A acc 21 4 ADD A,[expr] direct 02 6 INC X x 22 4 ADD A,[X+expr] index 03 7 INC [expr] direct 23 7 ADC A,expr data 04 4 INC [X+expr] index 24 8 ADC A,[expr] direct 05 6 DEC A acc 25 4 ADC A,[X+expr] index 06 7 DEC X x 26 4 SUB A,expr data 07 4 DEC [expr] direct 27 7 SUB A,[expr] direct 08 6 DEC [X+expr] index 28 8 SUB A,[X+expr] index

Summary of the content on the page No. 7

CY7C63413C CY7C63513C CY7C63613C Memory Organization Program Memory Organization after reset Address 14-bit PC 0x0000 Program execution begins here after a reset 0x0002 USB Bus Reset interrupt vector 0x0004 128-µs timer interrupt vector 0x0006 1.024-ms timer interrupt vector 0x0008 USB address A endpoint 0 interrupt vector 0x000A USB address A endpoint 1 interrupt vector 0x000C USB address A endpoint 2 interrupt vector 0x000E Reserved 0x0010 Reserved 0x0012 Reserved 0x0014 DAC interrupt vector

Summary of the content on the page No. 8

CY7C63413C CY7C63513C CY7C63613C Data Memory Organization into four areas: program stack, data stack, user variables and USB endpoint FIFOs as shown below: The CY7C63413C/513C/613C microcontrollers provide 256 bytes of data RAM. In normal usage, the SRAM is partitioned after reset Address 8-bit PSP 0x00 Program Stack begins here and grows upward 8-bit DSP user Data Stack begins here and grows downward The user determines the amount of memory required User Variables 0xE8 USB FIFO for Address A e

Summary of the content on the page No. 9

CY7C63413C CY7C63513C CY7C63613C I/O Register Summary lator to the selected port. Indexed I/O Write (IOWX) adds the contents of X to the address in the instruction to form the port I/O registers are accessed via the I/O Read (IORD) and I/O address and writes data from the accumulator to the specified Write (IOWR, IOWX) instructions. IORD reads the selected port. Note that specifying address 0 (e.g., IOWX 0h) means port into the accumulator. IOWR writes data from the accumu- the I/O port is sele

Summary of the content on the page No. 10

CY7C63413C CY7C63513C CY7C63613C Clock Distribution XTALOUT clk1x (to USB SIE) Clock clk2x Doubler (to Microcontroller) XTALIN 30 pF 30 pF Figure 2. Clock Oscillator On-chip Circuit processing does NOT push the program counter, carry flag, Clocking and zero flag onto program stack. That means the reset The XTAL and XTAL are the clock pins to the microcon- handler in firmware should initialize the hardware and begin IN OUT troller. The user can connect a low-cost ceramic resonator or executing t

Summary of the content on the page No. 11

CY7C63413C CY7C63513C CY7C63613C initialization noted under “Reset,” bit 6 of the Processor Status General Purpose I/O Ports and Control Register is set to “1” to indicate to the firmware that a Watch Dog Reset occurred. Ports 0 to 2 provide 24 GPIO pins that can be read or written. Each port (8 bits) can be configured as inputs with internal pull- The Watch Dog Timer is a 2-bit timer clocked by a 4.096-ms ups, open drain outputs, or traditional CMOS outputs. Please clock (bit 11) from the free

Summary of the content on the page No. 12

CY7C63413C CY7C63513C CY7C63613C Table 5. Port 3 Data Addr: 0x03 Port 3 Data P3[7] P3[6] P3[5] P3[4] P3[3] P3[2] P3[1] P3[0] R/W R/W R/W R/W R/W R/W R/W R/W Table 6. DAC Port Data Addr: 0x30 DAC Port Data Low current outputs High current outputs 0.2 mA to 1.0 mA typical 3.2 mA to 16 mA typical DAC[7] DAC[6] DAC[5] DAC[4] DAC[3] DAC[2] DAC[1] DAC[0] R/W R/W R/W R/W R/W R/W R/W R/W Port 3 has eight GPIO pins. Port 3 (8 bits) can be configured During reset, all of the bits in the GPIO to a def

Summary of the content on the page No. 13

CY7C63413C CY7C63513C CY7C63613C Table 11.Possible Port Configurations Port Configuration bits Pin Interrupt Bit Driver Mode Interrupt Polarity 11 X Resistive - 10 0 CMOS Output disabled 10 1 Open Drain disabled 01 X Open Drain - 00 X Open Drain + (default) In “Resistive” mode, a 7-kΩ pull-up resistor is conditionally direction. If a port’s associated Interrupt Mask bits are cleared, enabled for all pins of a GPIO port. The resistor is enabled for those port bits are strictly outputs. If the In

Summary of the content on the page No. 14

CY7C63413C CY7C63513C CY7C63613C Table 13.DAC Port Data Addr: 0x30 DAC Port Data Low current outputs High current outputs 0.2 mA to 1.0 mA typical 3.2 mA to 16 mA typical DAC[7] DAC[6] DAC[5] DAC[4] DAC[3] DAC[2] DAC[1] DAC[0] R/W R/W R/W R/W R/W R/W R/W R/W The DAC port provides the CY7C63513C with 8 program- this feature with an interrupt mask bit for each DAC I/O pin. mable current sink I/O pins. Writing a “1” to a DAC I/O pin Writing a “1” to a bit in this register enables interrupts from

Summary of the content on the page No. 15

CY7C63413C CY7C63513C CY7C63613C 7. The USB Controller decodes the request and retrieves the USB Serial Interface Engine (SIE) Device descriptor from the program memory. The SIE allows the microcontroller to communicate with the 8. The host performs a control read sequence and the USB USB host. The SIE simplifies the interface between the micro- Controller responds by sending its Device descriptor over controller and USB by incorporating hardware that handles the the USB bus. following USB b

Summary of the content on the page No. 16

CY7C63413C CY7C63513C CY7C63613C The Bus Activity bit is a “sticky” bit that indicates if any non-idle are cleared during a reset, setting the USB device address to USB event has occurred on the USB bus. The user firmware zero and marking this address as disabled. Figure 18 shows should check and clear this bit periodically to detect any loss the format of the USB Address Register. of bus activity. Writing a “0” to the Bus Activity bit clears it while Bit 7 (Device Address Enable) in the USB De

Summary of the content on the page No. 17

CY7C63413C CY7C63513C CY7C63613C The ‘Acknowledge’ bit is set whenever the SIE engages in a While the ‘set-up’ bit is set, the CPU cannot write to the DMA transaction that completes with an ‘ACK’ packet. buffers at memory locations 0xE0 through 0xE7 and 0xF8 through 0xFF. This prevents an incoming set-up transaction The ‘set-up’ PID status (bit[7]) is forced HIGH from the start of from conflicting with a previous In data buffer filling operation the data packet phase of the set-up transaction,

Summary of the content on the page No. 18

CY7C63413C CY7C63513C CY7C63613C upper 4 bits into a temporary register. When the firmware 12-bit Free-running Timer reads the upper 4 bits of the timer, it is actually reading the The 12-bit timer provides two interrupts (128 µs and 1.024 ms) count stored in the temporary register. The effect of this logic and allows the firmware to directly time events that are up to is to ensure a stable 12-bit timer value can be read, even when 4 ms in duration. The lower 8 bits of the timer can be read the

Summary of the content on the page No. 19

CY7C63413C CY7C63513C CY7C63613C The “Single Step” (bit 1) is provided to support a hardware During Power-on Reset, the Processor Status and Control debugger. When single step is set, the processor will execute Register is set to 00010001, which indicates a Power-on Reset one instruction and halt (clear the run bit). This bit must be (bit 4 set) has occurred and no interrupts are pending (bit 7 cleared for normal operation. clear) yet. The “Interrupt Mask” (bit 2) shows whether interrupts are D

Summary of the content on the page No. 20

CY7C63413C CY7C63513C CY7C63613C Interrupt Vectors 0x0000—which corresponds to the first entry in the Interrupt Vector Table. Because the JMP instruction is 2 bytes long, the The Interrupt Vectors supported by the USB Controller are interrupt vectors occupy 2 bytes. listed in Table 27. Although Reset is not an interrupt, per se, the first instruction executed after a reset is at PROM address Table 27.Interrupt Vector Assignments Interrupt Vector Number ROM Address Function not applicable 0x0000


Alternative user manuals
# User manual Category Download
1 Cypress CapSense CY8C20x36 User manual Computer Hardware 0
2 Cypress CY14B101L User manual Computer Hardware 0
3 Cypress CY14B101LA User manual Computer Hardware 0
4 Cypress CY14B104N User manual Computer Hardware 0
5 Cypress AutoStore STK14CA8 User manual Computer Hardware 0
6 Cypress CY14B101Q2 User manual Computer Hardware 0
7 Cypress CY14B104L User manual Computer Hardware 0
8 Cypress CY2048WAF User manual Computer Hardware 0
9 Cypress CY14B108L User manual Computer Hardware 0
10 Cypress 7C185-15 User manual Computer Hardware 0
11 Cypress CY14B104NA User manual Computer Hardware 0
12 Cypress CY14B104M User manual Computer Hardware 0
13 Cypress AutoStore STK17TA8 User manual Computer Hardware 0
14 Cypress CY62158E User manual Computer Hardware 0
15 Cypress CY14B256L User manual Computer Hardware 0
16 Sony MSAKIT-PC4A User manual Computer Hardware 2
17 Sony MRW62E-S1 2694866142 User manual Computer Hardware 5
18 Philips MATCH LINE 9596 User manual Computer Hardware 17
19 Sony 64GB SDHC Class 10 Memory Card Readers SF32UY User manual Computer Hardware 1
20 Philips PSC702 User manual Computer Hardware 1