Summary of the content on the page No. 1
MVME3100
Single-Board Computer
Installation and Use
V3100A/IH1
January 2006 Edition
Summary of the content on the page No. 2
© Copyright 2006 Motorola Inc. All rights reserved. Printed in the United States of America. Motorola and the stylized M logo are trademarks of Motorola, Inc., registered in the U.S. Patent and Trademark Office. All other product or service names mentioned in this document are the property of their respective owners.
Summary of the content on the page No. 3
Safety Summary The following general safety precautions must be observed during all phases of operation, service, and repair of this equipment. Failure to comply with these precautions or with specific warnings elsewhere in this manual could result in personal injury or damage to the equipment. The safety precautions listed below represent warnings of certain dangers of which Motorola is aware. You, as the user of the product, should follow these warnings and all other safety precautions necessa
Summary of the content on the page No. 4
Flammability All Motorola PWBs (printed wiring boards) are manufactured with a flammability rating of 94V-0 by UL-recognized manufacturers. EMI Caution Caution This equipment generates, uses and can radiate electromagnetic energy. It may cause or be susceptible to electromagnetic interference (EMI) if not ! installed and used with adequate EMI protection. Caution Lithium Battery Caution This product contains a lithium battery to power the clock and calendar circuitry. Caution Danger of explos
Summary of the content on the page No. 5
CE Notice (European Community) Warning This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take ! adequate measures. Warning Motorola products with the CE marking comply with the EMC Directive (89/336/EEC). Compliance with this directive implies conformity to the following European Norms: EN55022 “Limits and Methods of Measurement of Radio Interference Characteristics of Information Technology Equipment”;
Summary of the content on the page No. 6
Notice While reasonable efforts have been made to assure the accuracy of this document, Motorola, Inc. assumes no liability resulting from any omissions in this document, or from the use of the information obtained therein. Motorola reserves the right to revise this document and to make changes from time to time in the content hereof without obligation of Motorola to notify any person of such revision or changes. Electronic versions of this material may be read online, downloaded for persona
Summary of the content on the page No. 7
Contents About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xv Overview of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xv Comments and Suggestions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xvi Conventions Used in This Manual . . . . . . . . . . .
Summary of the content on the page No. 8
Contents Command Line Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 MOTLoad Command List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Default VME Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Firmware Settings . . . . . . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 9
Contents Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 PMC Expansion Connector (J4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Ethernet Connectors (GENET1/J41B, GENET2/J2B, ENET1/J2A) . . . . . . . . . . . . . . . . . . . . . . 50 PCI Mezzanine Card (PMC) Connectors (J11 – J14, J21 – J23) . . . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 10
List of Figures Figure 1-1. MVME3100 Board Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Figure 4-1. MVME3100 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Figure 4-2. MVME721 RTM Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 MVME3100 Installation and Use (V3100A/IH1) xi
Summary of the content on the page No. 11
List of Tables Table 1-1. Startup Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Table 1-2. Configuration Switch (S4) Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Table 1-3. Geographical Address Switch Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Table 1-4. Slot Geographical Address Settings . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 12
About This Manual The MVME3100 Single-Board Computer Installation and Use manual provides the information you will need to install and configure your MVME3100 single-board computer and MVME721 rear transition module (RTM). It provides specific preparation and installation information, and data applicable to the board. As of the printing date of this manual, the MVME3100 supports the models listed below. Model Number Description MVME3100-1152 677 MHz MPC8540 PowerQUICC III™ integrated processo
Summary of the content on the page No. 13
About This Manual Comments and Suggestions Motorola welcomes and appreciates your comments on its documentation. We want to know what you think about our manuals and how we can make them better. Mail comments to: Motorola, Inc. Embedded Communications Computing Reader Comments DW278 2900 S. Diablo Way Tempe, Arizona 85282 You can also submit comments to the following e-mail address: reader-comments@mcg.mot.com In all your correspondence, please list your name, position, and company. Be sure to
Summary of the content on the page No. 14
1 Hardware Preparation and Installation 1 Introduction This chapter contains the following information: ■ Board preparation and installation instructions ■ ESD precautionary notes Description The MVME3100 is a single-slot, single-board computer based on the MPC8540 PowerQUICC III™ integrated processor. The MVME3100 provides serial ATA (sATA), USB 2.0, 2eSST VMEbus interfaces, dual 64-bit/100 MHz PMC sites, up to 128MB of Flash, dual 10/100/1000 Ethernet, one 10/100 Ethernet, and five serial p
Summary of the content on the page No. 15
Chapter 1 Hardware Preparation and Installation Overview of Startup Procedures The following table lists the things you will need to do before you can use this board and tells where to find the information you need to perform each step. Be sure to read this entire chapter, including all Caution and Warning notes, before you begin. Table 1-1. Startup Overview What you need to do... Refer to... Unpack the hardware. Unpacking Guidelines on page 2 Identify various components on the board. MVME3100
Summary of the content on the page No. 16
Chapter 1 Hardware Preparation and Installation Warning Dangerous voltages, capable of causing death, are present in this equipment. Use extreme caution when handling, testing, and adjusting. Warning Hardware Configuration This section discusses certain hardware and software tasks that may need to be performed prior to installing the board in a chassis. To produce the desired configuration and ensure proper operation of the MVME3100, you may need to carry out certain hardware modifications be
Summary of the content on the page No. 17
ABORT/RESET USER 1 FAIL SPEED ACT PMC 2 PMC 1 SATA 1 COM 1 G ENET 1 Chapter 1 Hardware Preparation and Installation The MVME3100 is factory tested and shipped with the configuration described in the following sections. Figure 1-1. MVME3100 Board Layout J25 J24 J28 J30 U1014 J21 J22 U1050 U1049 U1020 P1 U1019 J23 U1025 U1052 U1046 U1026 U1047 U1027 U1008 J11 J12 U21 U1051 J13 J14 U1003 U1007 P2 U1010 U1012 U1000 J2 U1012 U1024 J4 4381 0106 4 MVME3100 Installation and Use (V3100A/IH1)
Summary of the content on the page No. 18
Chapter 1 Hardware Preparation and Installation Configuration Switch (S4) An 8-position SMT configuration switch controls the VME SCON setting, Flash bank write- protect, and the safe start ENV settings. It also selects the Flash boot image. The default setting on all switch positions is OFF. Table 1-2. Configuration Switch (S4) Settings Setting Switch Pos. OFF (Factory Default) ON Notes SAFE_START 1 Normal ENV settings Safe ENV settings This switch status is should be used. should be used. r
Summary of the content on the page No. 19
Chapter 1 Hardware Preparation and Installation Geographical Address Switch (S3) The TSi148 VMEbus Status register provides the VMEbus geographical address of the MVME3100. This switch reflects the inverted states of the geographical address signals. Applications not using the 5-row backplane can use the geographical address switch to assign a geographical address. 1 16 1 16 ON ON 1 Not used 1 Not used 2 PCI mode 2 PCI-X mode 3 GAP#=0 3 GAP#=1 4 GA4#=0 4 GA4#=1 5 GA3#=0 5 GA3#=1 6 GA2#=0 6 GA
Summary of the content on the page No. 20
Chapter 1 Hardware Preparation and Installation Table 1-4. Slot Geographical Address Settings (continued) Slot GAP Address GA(4:0) SW3 SW4 SW5 SW6 SW7 SW8 10 0 10101 ON OFF ON OFF ON OFF 11 1 10100 OFF OFF ON OFF ON ON 12 0 10011 ON OFF ON ON OFF OFF 13 1 10010 OFF OFF ON ON OFF ON 14 1 10001 OFF OFF ON ON ON OFF 15 0 10000 ON OFF ON ON ON ON 16 1 01111 OFF ON OFF OFF OFF OFF 17 0 01110 ON ON OFF OFF OFF ON 18 0 01101 ON ON OFF OFF ON OFF 19 1 01100 OFF ON OFF OFF ON ON 20 0 01011 ON ON OFF ON
