Summary of the content on the page No. 1
Summary of the content on the page No. 2
TABLE of CONTENTS 1. PRODUCT OVERVIEW ......................................................................................................................................................... 4 1.1 What’s Included ................................................................................................................................................... 4 1.2 Safety Instructions
Summary of the content on the page No. 3
7.3 Warranty Terms and Conditions ..................................................................................................................... 31 8. COMPLIANCE INFORMATION ........................................................................................................................................ 33 8.1 FCC Notice ....................................................
Summary of the content on the page No. 4
1. PRODUCT OVERVIEW 1.1 What’s Included The following items are included with InterView: InterView Monitor: Dual – 17 Inch – LCD Panels InterView Multiplatform Control Base AC Power Adapter Power Cord DMS to DUAL DVI-I Signal Cable DVI-I to VGA Adapter Microphone Audio Cable USB Cable Visual Guide Drivers and Software CD 4
Summary of the content on the page No. 5
1.2 Safety Instructions Safe Environment Do not store or use the InterView in locations that are exposed to heat, extreme cold, high humidity or dusty environment. Room temperature conditions are recommended. Do not subject InterView to severe vibrations or high impact conditions. Do not allow water or other liquids to spill on or into InterView. InterView may become unstab
Summary of the content on the page No. 6
1.3 Product Views Panel Front View 1. Integrated Webcam 2. Balance Bar 3. Multiplatform Control Base 4. Integrated 3-Port USB 2.0 Hub 5. 17 Inch LCD Panels 5 5 1 3 2 4 6
Summary of the content on the page No. 7
Control Base Front View 1. Power Button 2. Power Light Indicator (Left Panel) 3. Power Light Indicator (Right Panel) 4. Panel Selection Button 5. Brightness Adjust (Down) 6. Brightness Adjust (Up) 7. Auto Adjust 8. Integrated Microphone 2 1 3 5 6 7 4 8 7
Summary of the content on the page No. 8
Control Base Back View 1. USB to PC Port 2. Microphone Jack 3. DMS Port 4. AC Power Connector 1 3 4 2 8
Summary of the content on the page No. 9
2. INTERVIEW SPECIFICATIONS 2.1 InterView Technical Specifications General Model number EVGA InterView 1700 LCD Screen type 17’’Wide TFT Preset display area Horizontal 367.20 mm Vertical 229.50 mm Synchronization Horizontal 31.5 kHz to 81.1 kHz Vertical 56 Hz to 76 Hz Viewing angle Horizontal 20° / 35° (CR=10) Vertical 45° /
Summary of the content on the page No. 10
2.2 Preset Timing Modes The screen will be adjusted automatically when the signal transferred from the computer is the same as the following Preset Timing Modes. If your display mode is not listed, it is not supported by this monitor; the screen may go blank while the power LED is on. Horizontal Frequency Vertical Frequency Sync Polarity Display Mode Pixel Clock (MHz) (kHz) (Hz) (
Summary of the content on the page No. 11
3. SETTING UP INTERVIEW Read the safety instructions before setting up the InterView. 3.1 Steps to Assembling InterView 1. Rotate the balance bar out from the bottom of the base: 2. Remove the caps on the stand and the panel: 3. Assemble the stand and the panel: 11
Summary of the content on the page No. 12
4. Push in the button and turn it clockwise to lock up the stand and the panel: 5. Open up the panel: 6. Push the balance bar back into the base: 12
Summary of the content on the page No. 13
3.2 Connecting InterView to a PC Before setting up InterView, you must power down your computer(s). 1. Connect the monitor to a computer(s) using the DMS to Dual DVI-I cord. Note: You can use either the D-Sub plug or the DVI-D plug if there’s no available DVI-I port on your PC. 2. Plug the power cord into the power adapter: 3. Connect the monitor to the electrical outl
Summary of the content on the page No. 14
4. Power on InterView and the computer(s): 5. Use the audio cable to connect InterView to the MIC or Line-in input of the computer. This is required to use the onboard microphone. 6. Connect InterView to the computer(s) with the USB cable to enable the front USB 2.0 HUB located on the monitor base. This is also required to use
Summary of the content on the page No. 15
3.3 Plug and Play Compatibility You can use InterView with any Plug and Play compatible system. The system configures itself and optimizes the display’s settings. In most cases, InterView‘s installation is automatically processed unless the user intervenes. 15
Summary of the content on the page No. 16
4. HOW TO ADJUST INTERVIEW 4.1 Rotating/Folding Each panel can rotate 180 degrees. The display will automatically adjust to the correct position. Each panel can be opened and closed 90 degrees horizontally. 16
Summary of the content on the page No. 17
4.2 Control Buttons 2 3 4 5 1 1. Power Button: Powers the InterView ON or OFF 2. Panel Selection Button: Selects the monitor to be adjusted 3. Brightness Adjust (Down): Decreases brightness levels 4. Brightness Adjust (Up): Increases brightness levels 5. Auto Adjust: Adjusts vertical position, phase, horizontal position, and pixel clock automatically
Summary of the content on the page No. 18
5. SYSTEM REQUIREMENTS AND SOFTWARE INSTALLATION 5.1 System Requirements Operating Systems Supported: - Windows XP Home Edition - Windows XP Professional - Windows XP Professional X64 Edition - Windows Vista™ - Windows Vista™ 64-bit Hardware: - 64MB of System Memory or more - 50MB Hard Disk space or more O
Summary of the content on the page No. 19
(Step 2) Processing Installation - Click Webcam software installation to start the installation process - Click Next, select the application you would like to install, then click Next to continue Note: For users who select to install both webcam driver and application, the installation will starts from the webcam software then to the webcam driver. Installing the
Summary of the content on the page No. 20
- Installation in process, the dialogue box will automatically close when the installation completes. Installing the Webcam Driver - Click Install - Click Install 20
