Summary of the content on the page No. 1
FT710
17” Flat CRT
User’s
Manual
By Envision Peripherals, Inc.
www.aocmonitor.com
Summary of the content on the page No. 2
Thank you very much for choosing the AOC Color Monitor. We recommend that you take a few minutes to read carefully through this brief but comprehensive manual before installing and switching on the monitor. Please keep this manual in a safe place for your future reference. Plug & Play Drivers for the AOC Series Monitors are available at: www.aocmonitor.com CHECKING THE CONTENTS OF THE MONITOR PACKAGE The product package should include the following items: 1. Monitor 2. Ow
Summary of the content on the page No. 3
FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may caus
Summary of the content on the page No. 4
PRECAUTIONS Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance. Use only a cart or stand recommended by the manufacturer or sold with the monitor. If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacturer and follow the kit ins
Summary of the content on the page No. 5
Plug & Play DDC1/2B Feature This monitor is equipped with VESA DDC1/2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. The communication channel is defined in two levels, DDC1 and DDC2B. The DDC1 is a unidirectional data channel from the display to the host that continuously transmits EDID information. The DDC2B is a
Summary of the content on the page No. 6
TECHNICAL SUPPORT(FAQ) Power LED is not on *Power Cord should be connected No Plug & Play *Check if the PC System is Plug & Play compatible *Check if the Video Card is Plug & Play compatible *Check if the D-15 plug pin of Video Cable is bent *Make sure the AOC Monitor Drivers are installed (AOC Monitor Drivers are available at: www.aocmonitor.com) Picture is fuzzy *Adjust the Contrast and Brightness Controls. Picture bounces or a wave pattern is present in the picture *Move elect
Summary of the content on the page No. 7
INSTALLATION INSTRUCTIONS SWIVEL BASE To attach the swivel base to the monitor, do the following: • Carefully turn the monitor on its side or upside down. (see figure 1) • Locate the cavities at the bottom front of the monitor. • Insert the pegs on the swivel base into these cavities. Push the swivel base forward until the swivel base locks in place. • To remove the swivel base, hold the bottom of the swivel base, then push it out. POWER CORD Power Source: 1. Make sure the po
Summary of the content on the page No. 8
OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS The other control knobs are located at the base of the monitor (See Figure 3). By changing these settings, the picture can be adjusted to your personal preferences. • The power cord should be connected. • Connect the video cable from the monitor to the video card. • To turn the monitor on, press the power switch to ON position. The power indicator will light up. • Your monitor features a unique quick switch system which provides a pictur
Summary of the content on the page No. 9
Figure 1: Installing and Removing the Swivel Base Figure 2: Connecting Cables 1. Signal Cable 2. Power Cord 3. VGA Card Connector Figure 3: External Controls 1. Power ON/OFF Switch 2. Power Indicator 3. Menu 4. Contrast/Right 5. Brightness/Left 6. Exti Figure 4: The OSD Menu 1024 × 768
Summary of the content on the page No. 10
FRONT PANEL CONTROL (see figure 3) NT PANEL CONTROL • Power ON/OFF Switch: Press this key to switch the display ON or OFF. • Power Indicator : Green — Power On mode. Orange — Off mode. • MENU : Press this key to either bring up the OSD menu or select an item on the menu. • Contrast: With the OSD menu on, press this key to either select a function or to adjust up the value of a selected function. With the OSD menu off, press this key to adjust the contrast. •
Summary of the content on the page No. 11
ADJUSTING THE PICTURE (see figure 4) 1. CONTRAST Adjust the picture contrast. 2. BRIGHTNESS Adjust the picture brightness. 3. H- CENTER Adjust the horizontal position of the picture. 4. H- SIZE Adjust the picture’s horizontal size. 5. V- CENTER Adjust the vertical position of the picture. 6. V- SIZE Adjust the picture’s vertical size. Adjust the picture’s horizontal and vertical size 7. ZOOM simultaneously. 8. PINCUSHION Adjust the pincushion and barrel.
Summary of the content on the page No. 12
SPECIFICATION CRT 43.2cm(17"), 90º deflection, 29mm neck, 21mm(H), 0.25mm(D) dot pitch Viewable Image Size 40.6cm (16"), diagonal Video 0.7Vpp, R, G, B Analog Separate Sync. TTL Level H/V-sync.: Positive/Negative Scanning Frequency: Horizontal 30kHz to 72kHz automatically Vertical 50Hz to 160Hz automatically Max. Resolution 1280 × 1024 Video Dot Rate 110MHz Factory Preset 6 Timings : User mode Timings : 8 Power Source Universal AC 100-240V, 50Hz/60Hz Operating 0°C to 40
Summary of the content on the page No. 13
Preset Timing Table STANDARD RESOLUTION HORIZONTAL VERTICAL FREQUENCY FREQUENCY IBM 720 x 400 31.5kHz 70Hz VGA 640 x 480 31.5kHz 60Hz VESA/85 640 x 480 43.3kHz 85Hz VESA/85 800 x 600 53.7kHz 85Hz VESA/85 1024 x 768 68.7kHz 85Hz VESA/60 1280 x 1024 64.0kHz 60Hz Connector Pin Assignment 15 6 10 11 15 PIN NO. PIN NO. DESCRIPTIO NO. de DESCRIPTI N Terminal ON PIN NO. 1. Video-Red 9. 5V 2. Video-Green 10. GND 3. Video-Blue 11. BLANK BLANK SDA (serial 4. 12. data addr
