Streszczenie treści zawartej na stronie nr. 1
Streszczenie treści zawartej na stronie nr. 2
5830_CIB_1ATT 2002.11.8 10:31 AM Page III Visit us at www.telephones.att.com © 2002 Advanced American Telephones. All Rights Reserved. AT&T and the Globe Design are trademarks of AT&T Corp., licensed to Advanced American Telephones. Printed in China. Issue 1AT&T 08/02
Streszczenie treści zawartej na stronie nr. 3
Streszczenie treści zawartej na stronie nr. 4
Streszczenie treści zawartej na stronie nr. 5
5830_CIB_1ATT 2002.11.8 10:31 AM Page 2 About Caller Identification (Caller ID) This product has a Caller ID with Call Waiting feature that works with service from your local phone service provider. Caller ID with Call Waiting lets you see who’s calling before you answer the phone, even when you’re on another call. You may need to change your phone service to use this feature. Contact your phone service provider if: • You have both Caller ID and Call Waiting, but as separate services (you m
Streszczenie treści zawartej na stronie nr. 6
5830_CIB_1ATT 2002.11.8 10:31 AM Page 3 INSTALLATION Table/Desktop Installation NOTE: Install this telephone away from electronic equipment, • such as personal computers, television sets or microwave ovens. Avoid excessive heat, cold, dust or moisture. 1 Connect the telephone line cord. 2 Connect the power cord. Standard Modular electrical telephone outlet jack Use only the power cord supplied with this product. If you need a replacement, call 1 800 222–3111. 3 INSTALLATION INSTALLATION
Streszczenie treści zawartej na stronie nr. 7
5830_CIB_1ATT 2002.11.8 10:31 AM Page 4 3 Install the handset battery. Use only AT&T Battery 2401, SKU# 91077. a) Remove battery b) Align the contacts and compartment cover by place the battery pack in pressing on the raised spot the battery compartment. and sliding downward. c) Replace cover by sliding it on its track up over battery case until it snaps firmly into place. 4 Charge the handset battery. • Place the handset in the base. • Charge the battery at least 12 hours. After the firs
Streszczenie treści zawartej na stronie nr. 8
5830_CIB_1ATT 2002.11.8 10:31 AM Page 5 Wall Installation 1 Connect the power cord and telephone line cord to the underside of the corded base, as shown (figure a). 2 Position the mounting bracket as shown (figure b). figure a 3 Feed the telephone line cord through the hole in the center of the mounting bracket (figure b), align the bracket with the base, and slide into the hole on the base as shown (figure c). 4 Lock the mounting bracket in place (figure d). 5 Plug the telephone line cord
Streszczenie treści zawartej na stronie nr. 9
5830_CIB_1ATT 2002.11.8 10:31 AM Page 6 Spare Battery/Power Failure Backup You can buy a spare handset battery (AT&T Battery 2401, SKU# 91077, sold separately) and keep it charged in the base at all times. In the event of a power failure, a fully charged battery in the spare battery compartment will allow you to make and receive calls from the 1 cordless handset only for up to 2 / hours. 2 The spare battery will fully charge in 24 hours. 6 INSTALLATION INSTALLATION
Streszczenie treści zawartej na stronie nr. 10
Streszczenie treści zawartej na stronie nr. 11
Streszczenie treści zawartej na stronie nr. 12
Streszczenie treści zawartej na stronie nr. 13
Streszczenie treści zawartej na stronie nr. 14
5830_CIB_1ATT 2002.11.8 10:31 AM Page 11 Ringer Volume Adjust the volume of the handset ringer. Setting the volume so that no bars show on the graph turns the ringer off. 1 Press MENU , then until the screen highlights HANDSET SETTINGS. 2Press . OK OK 3Press when RINGER VOLUME is highlighted. The screen displays RINGER iii iii iiiiiii ii VOLUME OK 4 Press or to hear samples of ring volumes. OK 5 Press to save the displayed setting. NOTE: Ringer Volume and Vibrate settings are • independent.
Streszczenie treści zawartej na stronie nr. 15
Streszczenie treści zawartej na stronie nr. 16
5830_CIB_1ATT 2002.11.8 10:31 AM Page 13 Vibrate Control When this feature is on, the handset vibrates when you have an incoming call. The default setting is OFF. 1 Press MENU , then until the screen highlights HANDSET SETTINGS. 2 Press OK , then until the screen highlights VIBRATE CONTROL. OK 3Press .The screen displays VIBRATE OFF iii iii iiiiiii ii OFF OK ON OFF ON 4Press or . OK 5 Press to save the displayed setting. NOTE: Vibrate and Ringer Volume settings are • independent. Adjusting V
Streszczenie treści zawartej na stronie nr. 17
5830_CIB_1ATT 2002.11.8 10:31 AM Page 14 Low Batt Tone You can set the handset to sound a tone when battery power is low, or you can turn the tone off. Default setting is ON. 1 Press MENU , then until the screen highlights HANDSET SETTINGS. 2 Press OK , then until the screen highlights LOW BATT TONE. OK 3 Press The screen displays . LOW BATTERY TONE iii iii iiiiiii ii ON OFF OK ON OFF ON 4Press or . OK 5 Press to save the displayed setting. 14 FEATURE SETUP – HANDSET FEATURE SETUP – HANDSET
Streszczenie treści zawartej na stronie nr. 18
5830_CIB_1ATT 2002.11.8 10:31 AM Page 15 Range Tone You can set the handset to sound a tone when you are approaching the range limit, or you can turn this tone off. The default setting is ON. 1 Press MENU , then until the screen highlights HANDSET SETTINGS. 2 Press OK , then until the screen highlights RANGE TONE. OK 3 Press The screen displays . iii iii RANGE TONE iiiiiii ii ON OFF OK ON OFF ON 4Press or . OK 5 Press to save the displayed setting. 15 FEATURE SETUP – HANDSET FEATURE SETUP –
Streszczenie treści zawartej na stronie nr. 19
Streszczenie treści zawartej na stronie nr. 20
