Streszczenie treści zawartej na stronie nr. 1
9371_book_1ATT 8/14/01 10:00 AM Page ii
USER’S MANUAL
Part 2
900 MHz Cordless
Telephone/Answering System
with Caller ID/Call Waiting 9371
DRAFT 8/14/01
Please also read
Part 1 — Important
Product Information
AT&T and the globe symbol are registered trademarks of AT&T Corp. licensed to Advanced American Telephones.
Streszczenie treści zawartej na stronie nr. 2
9371_book_1ATT 8/14/01 10:00 AM Page iii © 2001 Advanced American Telephones. All rights reserved. Printed in China. Issue 1AT&T 08/01
Streszczenie treści zawartej na stronie nr. 3
9371_book_1ATT 8/14/01 10:00 AM Page iv CONTENTS BEFORE YOU BEGIN . . . . . . 1 TELEPHONE MEMORY About Caller Identification ........... 1 AT THE BASE . . . . . . . . . . . . . 16 Store a Number in INSTALLATION . . . . . . . . . 2 Base Memory ...........................16 Before You Install .......................... 2 Dial a Number in Table/Desk Installation...................3 Base Memory........................... 16 Wall Installation ............................ 5 CALLER ID OPERATION .
Streszczenie treści zawartej na stronie nr. 4
9371_book_1ATT 8/14/01 10:00 AM Page 1 BEFORE YOU BEGIN About Caller Identification (Caller ID) This product has a Caller ID with Call Waiting feature that works with service from your local phone service provider. Caller ID with Call Waiting lets you see who’s calling before you answer the phone, even when you’re on another call. You may need to change your phone service to use this feature. Contact your phone service provider if: • You have both Caller ID and Call Waiting, but as separate s
Streszczenie treści zawartej na stronie nr. 5
9371_book_1ATT 8/14/01 10:00 AM Page 2 INSTALLATION Before You Install 1 Choose a location for the base near an electrical outlet and a telephone jack. This phone requires a modular telephone jack and a standard electrical outlet (110v AC) not controlled by a wall switch. 2 Install the handset battery. a) Remove battery compartment cover by pressing on the indentation and sliding downward. b) Align two holes in plug with socket pins, and snap the plug into place. c) Place battery pack in c
Streszczenie treści zawartej na stronie nr. 6
9371_book_1ATT 8/14/01 10:00 AM Page 3 INSTALLATION 3 Attach belt clip to the cordless handset (optional). To attach To remove Table/Desk Installation Standard Modular electrical outlet telephone jack 1 Connect the telephone line cord. 2 Connect the power cord. Use only the power cord The ANSWER ON/OFF light goes on, supplied with this product. and CL flashes in the Message Window. If you need a replacement, call 1 800 222–3111. 3
Streszczenie treści zawartej na stronie nr. 7
9371_book_1ATT 8/14/01 10:00 AM Page 4 INSTALLATION 3 Charge the handset battery. Place the handset in the base. Charge the battery for at least 16 hours the first time. After the first charge, the battery is typically fully charged overnight. 4 Check for dial tone. After the batteries are charged, pick up the handset and press P; you should hear a dial tone. 5 Set the dial mode. If you have touch tone service, the phone is ready to use as soon as the batteries are charged. If you have dial
Streszczenie treści zawartej na stronie nr. 8
9371_book_1ATT 8/14/01 10:00 AM Page 5 INSTALLATION Wall Installation 1 Position the wall mount adapter on the base. Align tabs on wall mount adapter with holes on bottom of base. Snap wall mount adapter firmly into place. 5
Streszczenie treści zawartej na stronie nr. 9
9371_book_1ATT 8/14/01 10:00 AM Page 6 INSTALLATION 2 Connect the telephone line cord. 3 Connect the power cord. The ANSWER ON/OFF light goes on, and CL flashes in the Message Window. Use only the power cord supplied with this product. If you need a replacement, call 1 800 222–3111. 4 Mount the base on the wall. a) Align holes on base with mounting studs on wall jack. b) Place power c) Pull base down on cord as shown. mounting studs until it locks into place. 5 Follow Steps 3–6 in “Table/De
Streszczenie treści zawartej na stronie nr. 10
9371_book_1ATT 8/14/01 10:00 AM Page 7 TELEPHONE OPERATION AT THE HANDSET Answer a Call Press any key exceptO. Handset Volume While on a call, adjust volume of what you hear. Make a Call Flash/ Press P, then Call Waiting dial the number Access special — OR — telephone company subscriber services. Dial the number (use < to backspace End a Call and correct digits), Press O then press P to — OR — call. Place handset Enter programming while not on a call in base. Exit Hold programming Press to
Streszczenie treści zawartej na stronie nr. 11
9371_book_1ATT 8/14/01 10:00 AM Page 8 TELEPHONE OPERATION AT THE HANDSET Handset Ringer Style/Battery Save You can select from four different handset ringer styles, or turn the ringer off and extend the battery life. 1 Make sure the handset is off. 2 Press p to enter programming mode. 3 Press > until the screen displays RINGER:and the current setting. 4 Press s; the current setting blinks. 5 Press > to select 1, 2, 3, 4,or OFF. You will hear a sample of each ring. 6 Press s or p to choose t
Streszczenie treści zawartej na stronie nr. 12
9371_book_1ATT 8/14/01 10:00 AM Page 9 TELEPHONE OPERATION AT THE HEADSET Operating Range This cordless telephone operates within the maximum power allowed by the Federal Communications Commission (FCC). Even so, this handset and base can communicate over only a certain distance — which can vary with the locations of the base and handset, the weather, and the construction of your home or office. For best performance, keep the base antenna fully upright. If you receive a call while you are out
Streszczenie treści zawartej na stronie nr. 13
9371_book_1ATT 8/14/01 10:00 AM Page 10 TELEPHONE OPERATION AT THE BASE Speaker Volume While on a call, use to adjust the volume of what you hear. Base Ringer Volume Switch Use to adjust how loudly the base rings. Flash Access subscriber services while on a call. Mute Press M to prevent your caller from hearing you (you can hear your caller). Press again to deactivate. MUTE light is on when Mute is activated. Indicates On steadily: handset or base handset Make, Answer, is in base s
Streszczenie treści zawartej na stronie nr. 14
9371_book_1ATT 8/14/01 10:00 AM Page 11 TELEPHONE OPERATION AT THE BASE Page/Intercom 1 Press and release to signal someone at the handset. A paging tone sounds. 2 When the person at the handset presses I, the handset and base can communicate without tying up the phone line. 3 Press again or press o on handset to disconnect. Handset Locator Press to locate the handset. The handset will beep for up to one minute or until you turn it off by pressing again or pressing o on the handset. NOTE: Wh
Streszczenie treści zawartej na stronie nr. 15
9371_book_1ATT 8/14/01 10:00 AM Page 12 TELEPHONE MEMORY AT THE HANDSET One Touch Memory You can store one phone number (up to 16 digits) in the one touch memory location. NOTE: Press O at any time to exit memory. Store a Number in m 1 Press p to enter programming mode. 2 Press < or > until the screen displays SET ONE TOUCH. 3 Press s. A flashing cursor appears on screen. 4 Enter the telephone number you want to store. Use < to backspace and make a correction. 5 Press s or p to store the numb
Streszczenie treści zawartej na stronie nr. 16
9371_book_1ATT 8/14/01 10:00 AM Page 13 TELEPHONE MEMORY AT THE HANDSET This cordless handset can store an additional 50 telephone numbers with names in the directory, each up to 16 digits long. Entries are stored alphabetically. For consistency with Caller ID entries, you may wish to enter last names first. Note: Press O at any time to exit memory. Store a Number in the Directory 1 Press p. The screen displays DIRECTORY. 2 Press s. The screen displays ENTER NAME. 3 Using the chart below, ent
Streszczenie treści zawartej na stronie nr. 17
9371_book_1ATT 8/14/01 10:00 AM Page 14 TELEPHONE MEMORY AT THE HANDSET 4 When you finish entering the name, press s. The screen displays ENTER NUMBER. 5 Enter the telephone number. Use < to backspace and make a correction. Press r to store a pause in the dialing sequence. 6 Press s or p to store your entry. You’ll hear a series of beeps confirming the entry. Note: When memory is full the screen displays MEMORY FULL, an error tone sounds, and you will not be able to store a new number until
Streszczenie treści zawartej na stronie nr. 18
9371_book_1ATT 8/14/01 10:00 AM Page 15 TELEPHONE MEMORY AT THE HANDSET Delete a Number Stored in the Directory 1 Press > (DIR). The screen displays DIRECTORY. 2 Press < or > to scroll alphabetically through numbers stored in the directory —OR— Press the dial pad key for the first letter of the entry you want to delete. 3 When the screen displays the number you want to delete, press s. Then press > until ERASE flashes. DIAL EDIT EERRAASSEE 9735550123 4 Press s. The screen displays ERASE NO
Streszczenie treści zawartej na stronie nr. 19
9371_book_1ATT 8/14/01 10:00 AM Page 16 TELEPHONE MEMOR HEADLINE LEFT Y HEADLINE L-SUB AT THE BASE You can store 10 telephone numbers (up to 16 digits each) in the base memory locations (0-9). Store a Number in Base Memory 1 Press p on the base to enter programming mode. The SPEAKER light flashes. 2 Press M. 3 Press the dial pad key (0-9) for the location where you want to store the number. 4 Enter the telephone number. 4 Press p to store the number. You will hear a confirmation tone. Dial a
Streszczenie treści zawartej na stronie nr. 20
9371_book_1ATT 8/14/01 10:00 AM Page 17 CALLER ID OPERATION Caller’s name Indicates repeat call Caller’s telephone number Date of call Time of call Position of call in call history About Call History This phone assigns each incoming call a number from 1 to 50. The most recent call will have the highest number. When the memory is full, the oldest call information is deleted to make room for new incoming call information. For each call that comes in, the screen displays the following informat
