Instrukcja obsługi AT&T 9210

Streszczenie treści zawartej na stronie nr. 1

REVISED
10/17/00
USER’S MANUAL
Part 2
900 MHz Cordless
Telephone 9210
Fold open this manual for information about this
telephone’s installation and operation. Please
also read Part 1 — Important Product Information.
AT&T and the globe symbol are registered trademarks of AT&T Corp. licensed to Advanced American Telephones.
© 2000 Advanced American Telephones. All rights reserved.
Printed in Mexico. 850004300 Issue 1AT&T 10/00

Streszczenie treści zawartej na stronie nr. 2

INSTALLATION Before You Install This phone requires a modular telephone jack and a 1 Choose a location for the base near an electrical standard electrical outlet (110v AC) not controlled by a wall outlet and a telephone jack. switch. 2 Install the handset battery. a) Remove b) Plug battery c) Place battery battery pack connector pack and wires compartment into handset. in compartment. cover by d) Replace cover pressing on by sliding it up the indentation into place. and sliding downward. Table

Streszczenie treści zawartej na stronie nr. 3

INSTALLATION Wall Installation Standard electrical outlet 1 Connect the telephone Modular line cord. telephone jack Mounting studs 2 Connect the power cord. 3 Mount the base on the wall. Place power Align holes on base cord as shown, with mounting so it hangs studs on wall jack. straight down Pull base down on between base mounting studs and wall. until it locks into place. Use only the power cord supplied with this product. 4 Follow Steps 3–5 in If you need a replacement, call 1 800 222-3111. “

Streszczenie treści zawartej na stronie nr. 4

TELEPHONE OPERATION Headset Jack You can use this telephone hands-free when you install a 2.5 mm headset (SKU 24099), purchased separately. Plug the headset into the jack Handset Volume under the small rubber flap. Do Adjust volume of what you hear not force the connection, but through the handset. make sure the plug fits securely. Make or Answer a Call End a Call Place handset in base Lift handset from base — OR — — OR — Press O. Press P. Exit programming. Flash/Call Waiting Cancel a page. Ac

Streszczenie treści zawartej na stronie nr. 5

TELEPHONE OPERATION Indicates handset is Indicates handset is in use charging in base Page/ Handset Locator Press once to page the handset for up to one minute — OR — Press twice to cancel. 4

Streszczenie treści zawartej na stronie nr. 6

TELEPHONE MEMORY This cordless phone can store 10 telephone numbers, each up to 16 digits long. You can dial numbers stored in memory just by pressing M and a number button. Store Memory Numbers 1 Make sure the handset is off. 2 Press G. 3 Press the number button (0–9) where you want to store the telephone number. Store a Pause 4 Dial the telephone in a Memory Number number (up to 16 digits) Press to store a two-second pause — OR — in the dialing sequence. Each Press R to store the last press

Streszczenie treści zawartej na stronie nr. 7

BATTERIES Charging the Handset Battery Pack Replacing the Handset Battery Pack This battery should remain charged up to six days with the 1 Remove the battery compartment cover on the ringer turned on and up to 12 days with the ringer off. A handset by pressing on the indentation and sliding the fully charged battery provides an average talk time of about cover downward. six hours. 2 Lift out the old battery pack and disconnect. The battery pack needs charging when: 3 Plug battery pack connector

Streszczenie treści zawartej na stronie nr. 8

IN CASE OF DIFFICULTY If you have difficulty operating this phone, try the If you hear noise or interference when using the phone: suggestions below. For Customer Service, visit our website • Make sure the base antenna is fully upright. at www.telephones.att.com or call 1 800 222–3111. • You may be out of range. Move closer to the base. Please retain your receipt as your proof of purchase. • Press and release C to change to another of the 30 channels available. If noise is exceptionally loud, If