Streszczenie treści zawartej na stronie nr. 1
High-Resolution CMOS Camera
Model CSB1100CL-10
PRODUCT SPECIFICATION
Contents
Before use – General safety instructions
1. Product Description·········································· 1
2. Features ····························································· 1
3. Configuration···················································· 1
4. Optional parts ··················································· 1
5. Specifications··············································
Streszczenie treści zawartej na stronie nr. 2
BEFORE USE - GENERAL SAFETY INSTRUCTIONS This instruction manual contains important information for the operator (user) and/or people in the vicinity to avoid personal injury, or property damage. • Prior to use, read this operation manual carefully to fully understand its instructions for correct use. • After reading, keep this manual near the equipment for future reference. WARNINGS & CAUTIONS [Definition of markings] The meaning of each mark used in this instruction manual
Streszczenie treści zawartej na stronie nr. 3
●Handling Precautions WARNING Immediately cease use of the equipment in the event of abnormality or malfunction. If abnormal conditions are present, such as smoke, a burning smell, ingress of water or foreign matter, or if the equipment is dropped or malfunctions, fire or electric shock may result. If such abnormalities occur, disconnect the power plug from the outlet and contact your sales unplug representative. Do not use the equipment in locations subject to water splas
Streszczenie treści zawartej na stronie nr. 4
CAUTION Observe the following when installing the equipment: · Do not cover the equipment with a cloth, etc. · Do not place the equipment in a narrow location where heat is likely to accumulate. Otherwise, heat will accumulate inside the equipment, possibly resulting in a fire. Instruction Do not place the equipment in locations subject to high moisture, oil fumes, steam, or dust. Otherwise, fire or electric shock may result. Avoid Do not install the equipment i
Streszczenie treści zawartej na stronie nr. 5
CASES FOR INDEMNITY (LIMITED WARRANTY) We shall be exempted from taking responsibility and held harmless for damage or losses incurred by the user in the following cases. In the case damage or losses are caused by fire, earthquake, or other acts of God, acts by a third party, deliberate or accidental misuse by the user, or use under extreme operating conditions. In the case of indirect, additional, consequential damages (loss of business interests, suspension of business acti
Streszczenie treści zawartej na stronie nr. 6
Usage Precautions Handle carefully Do not drop the equipment or allow it to be subject to strong impact or vibration, as such action may cause malfunctions. Further, do not damage the connection cable, since this may cause wire breakage. Environmental operating conditions Do not use the product in locations where the ambient temperature or humidity exceeds the specifications. Otherwise, image quality may be degraded or internal components may be adversely affected. In parti
Streszczenie treści zawartej na stronie nr. 7
1. Product Description Model CSB1100CL-10 is a high-resolution B/W CMOS camera achieving high-speed image processing by a random access. 2. Features (1) Ultra-high resolution The CSB1100CL-10 features a high-pixel CMOS sensor (Total pixel count: 1.31 Mega pixels), enabling high-density images (i.e., significantly reduced moiré and beat) to be obtained. (2) Global shutter mode This model features a Global shutter mode, which means that clear images of a fast-moving subject w
Streszczenie treści zawartej na stronie nr. 8
5. Specification Model CSB1100CL-10 Image sensor CMOS Image sensor Total pixel 1280 (H) x 1024 (V) Active pixel 1240 (H) x 1023 (V) Pixel size 6.7 (H) x 6.7 (V) micro m Image area 8.308 x 6.854 mm Driving frequency 33.3333MHz Scanning line 1023 lines Scanning system Progressive Flame rate 22.2 fps (Under Rolling shutter mode and all pixel’s data read out mode) Sync system Internal Aspect ratio 5:4 Subject illumination 2600 lx, F5.6 (3100K) (Exposur
Streszczenie treści zawartej na stronie nr. 9
6. Connection (1) DC IN Connector (Camera side): HR10A-7R-6PB (Manufactured by HIROSE DENKI) Plug (Cable side): HR10A-7P-6S (Manufactured by HIROSE DENKI) Pin number Signal name １ １ １ １ ６ ６ ６ ６ 1 N.C. 2 N.C. ２ ２ ２ ２ ５ ５ ５ ５ 3 GND 4 N.C. ４ ４ ３ ３ ３ ３ ４ ４ 5 N.C. 6 +12V Rear-view (2) DATA IN/OUT Connector (Camera side): 10226-2210VE (Manufactured by 3M) Connector (Cable side): 10126-6000 (Manufactured by 3M) PIN. Signal Name I/O PIN. Signal Name I/O 1 GND 14 GND 2 TX OU
Streszczenie treści zawartej na stronie nr. 10
7. DIP switch setting The setting of each mode can be done with DIP switches located on the rear panel. OFF ON 1 Baud rate selection 2 3 Starting status setting 4 Rear DIP switch (1) Baud rate setting: Baud rate setting of camera IN /OUT [1] [2] Baud rate OFF OFF 9600 ON OFF 19200 OFF ON 38400 (2) Starting status setting: Designate the memory page readout in starting up of a camera [3] [4] Memory OFF OFF 1 ON OFF 2 OFF ON 3 ON ON 4 4 D4134040A
Streszczenie treści zawartej na stronie nr. 11
8. Function (1) Electronic shutter The shutter-speed of CSB1100CL-10 is also manually adjustable. By manipulating the internal register setting value of CSB1100CL-10, you can change the shutter-speed by user-defined setting value of 65.8 micro sec step. * The longer a user sets the exposure time, the more defective pixels on the image is outstanding. When you attach importance to image quality, it is recommendable to set the shutter speed at 30 msec or less. (2) Random trigger shutt
Streszczenie treści zawartej na stronie nr. 12
The placement is available up to 16 windows in all active pixel area. １ ２ ４ ３ ７ ５ ６ ８ ９ １１ １０ １２ １３ １４ １５ １６ The setting of readout address is available up to 8 types. １ ２ ３ ４ ５ ６ ７ ８ User can reprogram all setting types from 1 through 8. 6 D4134040A
Streszczenie treści zawartej na stronie nr. 13
Practical operation example In the case of only one readout area A readout area can be designated by the start (X1,Y1) address (X1, Y1) and the end address (X2, Y2). The (1) (2) (3) camera can read out the user-defined area through (4) (5) (6) this function. (7) (X2,Y2) The each address is designated by the start address and lengths (pixel numbers) of “X” and “Y” directions. (X1,Y1) Block A (1) (2) (3) In the case of more than two readout areas (4) (5) (6) The area designated by the
Streszczenie treści zawartej na stronie nr. 14
9. Timing Chart (1) Normal shutter mode (in all pixel data readout) Depends on register setting Integrate time EXPOSURE （CAMERA INTERNAL） Approx. 15.66us FRAME （CAMERA INTERNAL) Approx. 13.38us VIDEO DATA image A image B (CAMERA OUTPUT） 43.7ms 43.73ms + Exposure time (2) Random Trigger Shutter mode (Fix mode) Trigger disable time Trigger disable time TRIG （EXTERNAL） Depends on register Integrate setting Approx time no reaction . 28us EXPOSURE （CAMERA INTERNAL）
Streszczenie treści zawartej na stronie nr. 15
(3) Random trigger shutter (pulse mode) Shutter speed depends on the trigger pulse width. After trigger IN, next trigger signal is acceptable until the readout is completed. Trigger disable time Trigger disable time TRIG （EXTERNAL） Integrate Approx. Approx time 300ns no reaction . 28us EXPOSURE （CAMERA INTERNAL） Approx. 15.66us FRAME （CAMERA INTERNAL) Approx. 13.38us VIDEO DATA image A image B (CAMERA OUTPUT） 43.7ms 43.73ms + Exposure time (4) WOI (Window of interest) Depends on register s
Streszczenie treści zawartej na stronie nr. 16
11. External View 10 D4134040A
