Streszczenie treści zawartej na stronie nr. 1
KeypadLinc On/Off
Owner’s Manual
®
INSTEON 6-Button Scene Control Keypad, Dual-Band (#2487S)
Page 1 of 25 2487S - Rev: 1/21/2014 7:37 AM
Streszczenie treści zawartej na stronie nr. 2
ABOUT KEYPADLINC On/Off ..................................................................................................................... 3 Features and Benefits ................................................................................................................................. 4 What’s in the box? ..................................................................................................................................... 4 Optional Accessories .......................
Streszczenie treści zawartej na stronie nr. 3
ABOUT KEYPADLINC On/Off KeypadLinc On/Off (Dual-Band) is an elegant relay switch plus scene controller in one. In the 6-button configuration, the ON and OFF buttons control the connected load (light/appliance). Both the ON/OFF buttons plus the other 4 buttons can all control their own scene members (other INSTEON devices which respond to button presses on KeypadLinc). Furthermore, each button on KeypadLinc can itself be a member of countless scenes (giving you remote control of both the c
Streszczenie treści zawartej na stronie nr. 4
Features and Benefits • Easy to setup and use • Integrated 20 amp relay (incandescent loads up to 1800 watts) • Each button can be a scene controller • Each button can also be a scene responder • Each button can control the other buttons on the keypad (as well as remote devices) • Can support up to 400 scenes • Multiple buttons can be included in the same scene • Each button can be configured to: o Toggle between sending Ons and Offs (default) o Always send an On (scene trigger mode)
Streszczenie treści zawartej na stronie nr. 5
Optional Accessories Accessories Link Custom Etched and Pre- http://www.smarthome.com/_/KeypadLinc/KeypadLinc_Custom_Buttons Printed Buttons /_/2vj/2wf/nav.aspx Color and 6/8 Button http://www.smarthome.com/_/KeypadLinc/KeypadLinc_Change_Kits/_/2 Change Kits (15) vj/2wb/nav.aspx http://www.smarthome.com/2401BT10/Blank-10-Button-Set-for- Blank Buttons KeypadLinc-White/p.aspx http://www.smarthome.com/2401CLB/6-or-8-Button-Change-Kit-for- Clear Buttons KeypadLinc-Clear/p.aspx http://w
Streszczenie treści zawartej na stronie nr. 6
• LOAD (Optional) - usually black or red, feeds power to a connected lighting/appliance fixture. • NEUTRAL - usually white • GROUND - bare copper wire or metal fixture (if grounded) If you are having difficulties identifying wires, consult an electrician to help you. IMPORTANT! If you are not knowledgeable about, and comfortable with, electrical circuitry, you should have a qualified electrician install KeypadLinc for you. If you have any questions, please consult an electrician or call:
Streszczenie treści zawartej na stronie nr. 7
6) After you have connected all of the wires, ensure that all of the wire connectors are firmly attached and that there is no exposed copper except for the GROUND wire 7) Orienting KeypadLinc with the Set button on the bottom, gently place it into the junction box, and then screw it into place 8) Enable power to the switch from the circuit breaker or fuse panel 9) Verify KeypadLinc is working properly by turning the light on and off 10) Reinstall the trim plate Installation (for a circu
Streszczenie treści zawartej na stronie nr. 8
A wired-in 4 or more-way circuit (with three or more switches) has additional switches added in the middle of the circuit. In the diagram below, the additional switch (Switch 3+) is shown in two different positions since wiring can vary from home to home. To learn more about multi-way circuits, try Googling the search terms "3-way switch" or "4-way switch." Using KeypadLinc in Virtual Multi-Way Circuits By creating virtual, multi-way circuits, you can use KeypadLincs to replace switch
Streszczenie treści zawartej na stronie nr. 9
Notes: - One of the TRAVELER wires (TRAVELER 1, Red) is not used, so you will cap it off at both ends - The other TRAVELER (TRAVELER 2, Black) you will convert to a LINE wire. In the Secondary KeypadLinc’s junction box, connect TRAVELER 2 to the existing LINE and also to the KeypadLinc Secondary’s LINE wire. In the other junction box at the other end, you will connect TRAVELER 2 to the KeypadLinc Primary’s LINE wire. - The KeypadLinc Primary’s LOAD wire gets connected to the actual lig
Streszczenie treści zawartej na stronie nr. 10
between 110 and 120 Volts AC, that wire is the LINE wire (usually black). - The other two wires (usually black and red) are the TRAVELERS and go to the next junction box. TRAVELER wires are usually in the same cable sheath. - Turn off the electricity to resume installation 2) Connect the KeypadLinc Secondary’s LINE wire. The KeypadLinc that will be the Secondary goes in the junction box where you found the LINE wire. Connect the LINE wire that you found, the black TRAVELER, and the Keypad
Streszczenie treści zawartej na stronie nr. 11
7) Install additional switch/keypad Secondaries. If you have a 4-way or greater switching circuit, see Special Instructions For Large Multi-Way Circuits at the end of this section. 8) Identify the wires for the KeypadLinc Primary. The KeypadLinc Primary is the KeypadLinc that will actually control the load. In the junction box where you will install the KeypadLinc Primary, find the wire that carries power from the switch to the lights. This wire, called the LOAD wire, is commonly red. In th
Streszczenie treści zawartej na stronie nr. 12
1) Connect the KeypadLinc Secondary’s LINE Wire. Use a wire nut to connect both black TRAVELER wires to the KeypadLinc Primary’s black LINE wire. 2) Cap the two unused TRAVELERS. The other two TRAVELER wires (usually red) will not be used, so put wire nuts on the ends of them. 3) Cap the red LOAD wire from the KeypadLinc Secondary. Put a wire nut on the end of the KeypadLinc Secondary’s LOAD wire to ensure that it won’t connect to anything. 4) Connect the KeypadLinc Secondary’s NEUTRAL a
Streszczenie treści zawartej na stronie nr. 13
USING KEYPADLINC Button Taps Button Type Button’s LED Tap Double-tap Toggle Off Turn Scene On Turn Scene Members On Instantly Toggle On Turn Scene Off Turn Scene Members Off Instantly Always On Either Turn Scene On Turn Scene Members On Instantly Always Off Either Turn Scene Off Turn Scene Members Off Instantly Press and Holds First Press and Button Type Button’s LED Subsequent Press and Holds Hold Opposite of last Press and Hold Brighten Scene until Toggle Off release (e.g. if
Streszczenie treści zawartej na stronie nr. 14
• Tap the scene button you wish to setup before entering setup mode • Advanced setup features are highlighted in yellow • Toggle: Cycles automatically between “Toggle”, “Always Off”, “Always On” upon entry into this mode, then exists to Normal Operating Mode Add KeypadLinc Button to a Scene as a Controller (also known as Linking Mode) 1) Tap the KeypadLinc Scene button of choice (doesn’t matter if you send an on or an off) 2) Press and hold KeypadLinc’s Set button until it beeps Key
Streszczenie treści zawartej na stronie nr. 15
Add KeypadLinc Button to a Scene as a Responder (also known as Responder Setup) 3 1) Press and hold the Scene Controller (the other INSTEON device) button until it beeps Controller’s LED will blink 2) When the scene is activated 4 • If you want the LED ON i. Tap KeypadLinc’s Scene Responder button until LED is on • If you want the LED OFF i. Tap KeypadLinc’s Scene Responder button until LED is off 3) Press and hold KeypadLinc’s Set button until it double-beeps KeypadLinc’s scene b
Streszczenie treści zawartej na stronie nr. 16
2) Press and hold KeypadLinc’s Set button until it beeps KeypadLinc’s LED will begin blinking All illuminated LEDs on KeypadLinc will brighten to 100% 3) Press and hold the KeypadLinc’s Set button until it beeps again KeypadLinc’s LED will continue blinking 4) If responder has multiple buttons, tap the button you wish to remove from scene 5) Press and hold the Responder’s Set button until it double-beeps (or LEDS blink) KeypadLinc will (Beep)-(Beep) and its scene LED will stop blinki
Streszczenie treści zawartej na stronie nr. 17
ADVANCED FEATURES Using KeypadLinc as a Phase Bridge (Phase Bridging Detection Mode) KeypadLinc automatically bridges the electrical phases in your home (via communications with dual-band devices on the “other phase”). The following procedure to confirm that phases are bridged via KeypadLinc: 1) Start Phase Bridging Detection Mode by tapping the Set button on KeypadLinc four times quickly KeypadLinc will begin (Beeping) KeypadLinc LEDs that are on will illuminate at full brightness O
Streszczenie treści zawartej na stronie nr. 18
All the responders added above should respond to scene activations Remove Multiple Scene Responders at Once (also known as Multi-Unlinking Mode) 1) Tap the Scene controller button on KeypadLinc 2) Press and hold KeypadLinc’s Set Button until it beeps KeypadLinc’s scene button’s LED will begin blinking All illuminated LEDs on KeypadLinc will brighten to 100% 3) Press and hold KeypadLinc’s Set Button again until it beeps again KeypadLinc’s scene button’s LED will continue blinking 4
Streszczenie treści zawartej na stronie nr. 19
6) Test the group by controlling the load from Switch A and then Switch B The Load, Switch A and Switch B will all remain in synch Control Groups with more than 2 members Software is recommended for larger control groups. However, the following steps, when carefully followed, will also work. 1) Turn all N switches/dimmers on – to the same, desired scene level 2) Press and hold Switch A’s set button until it beeps (or LED blinks) Switch A’s LED will begin blinking 3) Tap Switch
Streszczenie treści zawartej na stronie nr. 20
“Radio” Button Groups (only 1 LED of “n” at a time) This feature is especially handy if you have multiple scenes controlling the same devices, such as Lights Bright, Lights Medium and Lights Off. When you press any of the scene buttons, the “others” LEDs will turn off (as if they were scene responders). Because of their complexity, software is recommended for radio button group setup. 1) Tap each radio group button until its LED is On 2) Press and hold button A until it beeps (about 10
