Streszczenie treści zawartej na stronie nr. 1
Mount
Cantilever Series
Installation Guide
Every effort has been made to provide accurate
and error-free assembly and installation.
DCS Mount disclaims liability for any difficulties
arising from the interpretation of information
contained in these instructions.
If DCS Mount products are used for purposes other
than their original intent. DCS Mount, its distributors
and retailers shall not be held responsible or liable
for injuries or property damage, direct indirect, or
consequential, which m
Streszczenie treści zawartej na stronie nr. 2
Illustration for hardware kit LP-80 Flat Panel Cantilever Mount Installation Instructions 80 lb. Maximum weight capacity VESA 75/100 compliant Cantilever arm mount for large LCD and small plasma panels Allows maximum flexibility for installing and viewing displays. Cantilever arm provides full extension and 180 of lateral rotation for viewing from multiple locations. Nesting arm design allows display to be folded parallel to wall Provides full tilt and swivel capabilities for opt
Streszczenie treści zawartej na stronie nr. 3
This flat panel cantilever will hold larger LCD monitor 30 inches and over. It will also hold smaller plasma monitors up to 32 inches. First determine if your monitor is VESA standard compliant, refer to the monitor’s users manual. VESA is a standard mounting hole pattern (see image 1). The LP-80 Flat Panel Cantilever can attach directly to both 75mm & 100mm VESA square hole patterns. If your monitor is not VESA standard compliant, a mounting adapter bracket will be needed between your mon
Streszczenie treści zawartej na stronie nr. 4
5. All of the screws are properly torqued to specification when the unit is assembled at the factory and should not need an further initial adjustments. However, due to the variety in size of different monitors, MINOR adjustment may be required to optimize the tension needed for ease of movement. Be sure that your monitor is supported properly while making ANY changes to the cantilever. To loosen or tighten the 4 screws respectfully on the back of the rear pivot clamp until the desired te
Streszczenie treści zawartej na stronie nr. 5
Mounting the Wall Plate Mounting to Wooden Stud 1. Determine the location where you want the display mounted on the wall. 2. USE stud finder to locate and mark the center of the two studs. 3. Remove P-150 from box. Remove the PA-4260 Adaptor plate from the Mounting Head, and set the four 3/8-16 button head screws aside for later. 4. Remove the cantilever arm from Wall Plate 5. Align center mounting holes of wall plate with center marks on studs. Using the wall plate as a template, mark t
Streszczenie treści zawartej na stronie nr. 6
Mounting Cantilever Assembly 1. Important: for the display to be centered over the wall plate when the cantilever arm is folded, the arm will need to be offset by approximately 4”(10.1cm) from the desired center position of the screen. To do this, first not where the desired center of screen position intersects the wall plate, and then mark the all plate. 2. Attach cantilever arm to the wall plate at the indicated offset location. 3. Mount cantilever assembly to wall using supplied 3/8” la
Streszczenie treści zawartej na stronie nr. 7
Configuring the PA-4260 adaptor plate (Installation instructions) PA-4260 Universal Plasma TV Adaptor Installation Instructions Fully adjustable design fits most large flat panel displays Includes complete hardware kit Quick mount capability with P-150 Durable grey or black powder coat finish Check the Hare Ware Kit after open the package ID* Description Quantity N/A Button Head Screw 1/4-20 x 1/2 14 N/A Washer 1/4 ID X 1/2 OD 4 N/A Nylon jam nut 2/4-20 4 A Button Head Screw 1/4-2
Streszczenie treści zawartej na stronie nr. 8
Set PA-4260 width The PA-4260 is capable of handling a wide range of landed insert widths. Measure the horizontal distance between mounting lands on your display, and set the width of the Mounting Rails as shown, Standard Range: 38 1/2”(98 cm) to 15 3/4”(40 cm) Standard Configuration For standard range configurations, loosen the screws on the sliders using the supplied Hex Wrench; adjust rails to desired width, and then re-tighten screws. Narrow Range: 15 1/2”(39 cm) to 3 1/2”(9 cm) Na
Streszczenie treści zawartej na stronie nr. 9
Mount PA-4260 to Display Hardware Selection a. Consult the supplied Hardware Cross Reference list. b. Select the mounting hardware for your display. Attach PA-4260 to Display a. Position the PA-4260 over back of display. b. Thread mounting screws through square washers and spacers (if required), as shown. c. Thread mounting screws through slots on side rails into landed inserts, and secure loosely. d. With mounting screws installed, center PA-4260 on the back of the display, and then tig
Streszczenie treści zawartej na stronie nr. 10
Mounting the display 1. Locate the set of four 3/8”-16 button head cap screws removed at the beginning of the installation. 2. Thread two of the screws approximately a 1/4”(0.6cm) into the upper set of PEM nuts on the adaptor plate, as shown 3. With the help of an assistant, carefully lift the display and hang it onto the P-150 by dropping the exposed portion of the screws down into the key slots on the nose piece of the P-150. 4. With the display hanging on the mount, thread the second
Streszczenie treści zawartej na stronie nr. 11
Vertical Tilt Function – raising and lowering the screen edge to improve viewing angle/picture quality. Operation – Loosen tilt tension screws with supplied 3/16” Hex wrench as shown. Adjust display for desired tilt angle. Re-tighten tension screws. CAUTION : It is important to try to maintain even torque on each of the 4 screws. Swivel Purpose – Optimize viewing angle for off center viewing positions. Operation – Grasp edges of display and swivel into desired position. Adjust swivel tens
Streszczenie treści zawartej na stronie nr. 12
HARDWARE CROSS REFERENCE LIST Fastener Manufacturer Model Spacer Part ID Part ID dia x length AKIRA EPM 420A/B NONE N/A 5mm x 15 J AKIRA EPM 600 NONE N/A 8mm x 20* N AKAI PDP4290 NONE N/A M8 x 35 P B & Q BEOVISION 4 3/4 x 3/8 D 8mm x 35 P BENQ PDP46W1 NONE N/A 6mm x 35 L DAWOO DP425M NONE N/A 5mm x 15 J DAWOO DSP4210 NONE N/A 5mm x 15 J DWIN HD-501 3/4 x 3/8 D 8mm x 35 P DWIN HD-50TS 3/4 x 3/8 D 8mm x 35 P ELECTROGRAPH DTS42DD 3/4 x 3/8 D 8mm x 35 P ELECTROGRAPH DTS4230 NONE N/A 5mm x 15
Streszczenie treści zawartej na stronie nr. 13
HARDWARE CROSS REFERENCE LIST Fastener Manufacturer Model Spacer Part ID Part ID dia x length HITACHI 50HDT50 NONE N/A 6mm x 16 L HITACHI 50HDT55 NONE N/A 6mm x 16 L HITACHI CMP4201 NONE N/A 6mm x 16 L HITACHI CMP4202 NONE N/A 6mm x 16 L HITACHI CMP5000WXV NONE N/A 6mm x 16 L HITACHI 32HDT20 NONE N/A 6mm x 16 L HITACHI 42HDT20 NONE N/A 6mm x 16 L HITACHI 42HDT50 NONE N/A 6mm x 16 L HITACHI 50HDT50 NONE N/A 6mm x 16 L JVC GM-P42UG NONE N/A 5mm x 15 J JVC PD-42WX84 NONE N/A 5mm x 15 J JVC
Streszczenie treści zawartej na stronie nr. 14
HARDWARE CROSS REFERENCE LIST Fastener Manufacturer Model Spacer Part ID Part ID dia x length NEC 42MP3 NONE N/A 5mm x 15 J NEC 42MP4 NONE N/A 5mm x 15 J NEC 42VP4A NONE N/A 5mm x 15 J NEC 42VP4D NONE N/A 5mm x 15 J NEC 50XM3A NONE N/A 5mm x 15 J NEC 50MP2 NONE N/A 5mm x 15 J DO NOT CANTILEVER NEC 61MP1 5mm x 15 J NEC PD-42XM1 NONE N/A 5mm x 15 J DO NOT CANTILEVER NEC PX-61M1A 5mm x 15 J PANASONIC PT-37PD4 3/4 x 3/8 D 8mm x 35 P PANASONIC PT-42PD1-P 3/4 x 3/8 D 8mm x 35 P PANASONIC PT-42
Streszczenie treści zawartej na stronie nr. 15
HARDWARE CROSS REFERENCE LIST Fastener Manufacturer Model Spacer Part ID Part ID dia x length PIONEER PRO800 NONE N/A 8mm x 20* N PIONEER PDP-433CMX NONE N/A 8mm x 20* N PIONEER PDP-4330HD NONE N/A 8mm x 20* N PIONEER PRO1000 NONE N/A 8mm x 20* N PIONEER PDP-502MX NONE N/A 8mm x 20* N PIONEER PDP-5030HD NONE N/A 8mm x 20* N PIONEER PDP-4340HD NONE N/A 8mm x 20* N PIONEER PDP-503CMX NONE N/A 8mm x 20* N PIONEER PDP-503MX NONE N/A 8mm x 20* N PIONEER PDP-610CMX DO NOT CANTILEVER 8mm x 20*
Streszczenie treści zawartej na stronie nr. 16
HARDWARE CROSS REFERENCE LIST Fastener Manufacturer Model Spacer Part ID Part ID dia x length SAMSUNG HPN6339 3/4 x 3/8 D 8mm x 35 P SAMSUNG HPM6315 DO NOT CANTILEVER 8mm x 35 P SAMSUNG PPM42S3 3/4 x 3/8 D 8mm x 35 P SAMSUNG PPM50H3 3/4 x 3/8 D 8mm x 35 P DO NOT CANTILEVER SAMSUNG PPM63H3 8mm x 35 P SAMSUNG SPL-4225K 3/4 x 3/8 D 8mm x 35 P SAMSUNG SPN-4235 3/4 x 3/8 D 8mm x 35 P SAMSUNG SPM-4227 3/4 x 3/8 D 8mm x 35 P SHARP PZ-43HV2U NONE N/A 8mm x 20 N SHARP PZ-50HV2U NONE N/A 8mm x 20
Streszczenie treści zawartej na stronie nr. 17
HARDWARE CROSS REFERENCE LIST Fastener Manufacturer Model Spacer Part ID Part ID dia x length YAMAHA PDM-1 3/4 x 3/8 D 8mm x 35 P ZENITH P40B24 NONE N/A 5mm x 15 J ZENITH P42W22B NONE N/A 5mm x 15 J ZENITH P42W26 NONE N/A 5mm x 15 J ZENITH P42W22BH NONE N/A 5mm x 15 J ZENITH P60W26 NONE N/A 8mm x 20 N DO NOT CANTILEVER ZENITH P60W26H 8mm x 20 N DO NOT CANTILEVER ZENITH DPDP60W 8mm x 16 M ZENITH P40V22 NONE N/A 5mm x 15 J ZENITH P40V24 NONE N/A 5mm x 15 J ZENITH P42W22B/H NONE N/A 5mm x 1
