Streszczenie treści zawartej na stronie nr. 1
2 Megapixel Full HDcctv
Indoor IR Dome Camera
Operation Instructions
Model No. EDH5240
Please read this manual first for correct installation and operation. This manual should be retained for future
reference. The information in this manual was current when published. The manufacturer reserves the right
to revise and improve its products. All specifications are therefore subject to change without notice.
PRECAUTIONS
1. Do not install the camera near electric or magnet
Streszczenie treści zawartej na stronie nr. 2
TABLE OF CONTENTS 1. PRODUCT OVERVIEW........................................................................................................... 2 1.1 Main Features ............................................................................................................................................... 2 1.2 Package Contents.......................................................................................................................................... 2 1.3 Specifications......
Streszczenie treści zawartej na stronie nr. 3
1. PRODUCT OVERVIEW The EDH5240 is an HDcctv 3-axis indoor dome camera with true Day/Night capability plus IR illumination, in a housing which can be surface or flush mounted. Based on a 2 megapixel progressive scan sensor for your choice of 1080 or 720 resolution HD 100% digital images, it delivers vastly superior video quality compared to traditional CCTV images. This superior resolution not only captures more critical evidentiary information, but the inherent ability for megapixel video
Streszczenie treści zawartej na stronie nr. 4
4 short screws to attach flush-mounting clips Rubber plug for side hole in outer base. Mounting template Power supply pigtail Video test cable Accessory pack #2 containing two flush mounting clips Please Note: If an item appears to have been damaged in shipment, replace it properly in its carton and notify the shipper. If any items are missing, notify your EverFocus Electronics Corp. Sales Representative or Customer Service. The shipping carton is the safest container in which
Streszczenie treści zawartej na stronie nr. 5
Certifications FCC/CE 1.4 Dimensions 2. MAJOR PARTS: NAMES AND FUNCTIONS Front View 1. Outer Base 3. Lens 2. IR LEDs 4. Light sensor 5. Cover - 4 -
Streszczenie treści zawartej na stronie nr. 6
Side View 6. Focus Adjust 7. Zoom Adjust 8. HDCC-TV Video Output 9. Power Input Back View 10. Video Test Output 11. OSD menu joystick 1. Base The camera unit sets in the dome base, when it is shipped from the factory. This base is used for surface mounting, and is discarded for flush mounting. - 5 -
Streszczenie treści zawartej na stronie nr. 7
2. IR LEDs 3. Lens The included vari-focal, DC iris lens allows manual adjustment of the field of view (zoom & focus). 4. Light Sensor Light sensor is used to detect the lighting level the environment. (The light sensor is “down” when the internal camera module is properly positioned). 5. Camera Cover This cover will protect the camera from dust and damage. 6. Focus Ring To set the focus, and loosen the focus ring knob, and turn the ring toward or as necessary, and re
Streszczenie treści zawartej na stronie nr. 8
3. 3-AXIS GIMBAL BRACKET The 3-axis gimbal enables installers to easily mount the camera on a wall or ceiling and then using the built in tilt and dual axis 180° twist, to adjust the viewing angle to the desired direction. With this unique 3-axis positioning system, installers can capture images from virtually any angle, without compromising performance. Loosen this screw manually to rotate the camera 180° Use a screw driver to loosen this screw. Tilt the camera 180°
Streszczenie treści zawartej na stronie nr. 9
4. INSTALLATION An EDH5240 camera may be mounted in two ways: surface mount and flush mount. Select the one that meets your needs. Installation - Surface Mount 1. Paste the drilling template on the ceiling or wall. Please refer to the drilling template below. 2. Use the appropriate tool to drill the INNER holes, and a clearance hole for the power and video wires. Note: The minimum recommended material thickness is 1 cm. 3. Use the plastic anchors and push them into the 4 sma
Streszczenie treści zawartej na stronie nr. 10
5. Pull the cables to be connected to power and video cables into the outer base from the ceiling or wall. Attach power supply pigtail adapter to power wire if needed. 6. Take a long Phillips pan head screw with a washer and tighten it into a plastic anchor. Repeat the same step until all the 4 screws are fixed to the wall. 7. Attach power and video cables from source to cables from camera and push excess wire back into hole. - 9 -
Streszczenie treści zawartej na stronie nr. 11
8. Insert inner base into outer base and secure using the 4 Phillips removed in the earlier step. Preposition camera so it is facing approximately in the desired direction. 9. Attach video test cable to test point on rear of camera module. Aim and focus the camera. Remove test cable. - 10 -
Streszczenie treści zawartej na stronie nr. 12
10. Once the camera view is as desired, attach the cover to outer base with the captive hex head screws. Installation - Flush Mount 1. Paste the drilling template on the ceiling or wall. Please refer to the drilling template below. 2. Use the appropriate tool to drill the OUTER holes; carefully cut along the dashed circle to create a clearance hole for the inner base unit. Note: The minimum recommended material thickness is 1 cm. 3. Pull the cables to be
Streszczenie treści zawartej na stronie nr. 13
4. Remove dome cover (hex, captive screws) 5. Unscrew the 4 Philips screws (retain for future use) to detach the inner base from the outer base. Set aside the outer base. 6. Screw the 2 spring tabs in the orientation shown to the slots at both sides of the inner base using the 4 Philips head screws provided. Attach the screws to the places marked “Fix”. - 12 -
Streszczenie treści zawartej na stronie nr. 14
7. Attach power and video cables from source to cables from camera and push excess wire back into hole. Fold the spring tabs up. 8. Preposition camera so it is facing approximately in the desired direction. 9. Push the entire inner base into ceiling while holding the spring tabs with both hands. - 13 -
Streszczenie treści zawartej na stronie nr. 15
10. The spring tabs will open automatically to support the camera against the ceiling. 11. Use the long Phillips pan head screws (x4) provided to screw the base to the ceiling. Do NOT use washers. - 14 -
Streszczenie treści zawartej na stronie nr. 16
12. Attach video test cable to test point on rear of camera module. Aim and focus the camera. Remove test cable. 13. Screw the cover back to the base with captive hex head screws. 4. OSD Menu & Configuration Access the user setup menu screen: I. Press inward on the end of the joystick The menu screen will appear on the monitor. II. Navigating with the joystick Angle the joystick or to move the cursor up or down. Angle the joystick or to adjus
Streszczenie treści zawartej na stronie nr. 17
Menu Tree s e L n — C D e t t r u h S — o t u A ; 0 5 / 1 ; 0 0 ; 5 0 6 / 1 1 2 1 1 0 ; / 0 1 / ; 1 2 / ; 0 / 0 5 1 0 0 1 ; ; 7 / 0 0 0 0 0 5 1 ; 0 0 6 / 1 0 ; / 1 ; 1 / 1 0 2 / 0 0 8 / 1 ; 0 1 0 5 e r u s o p x E C G A — h g i H d M ; e l d i w ; o L f f O ; C L B — f ; n O f O - t n l F i A e c i r k — f f O ; z H 0 5 z H 0 6 ; n r u t e R t u B W o A u e n W h s p O B
Streszczenie treści zawartej na stronie nr. 18
e T a P s t t e t n r — f ; n O f O r e R n u t t O u V T — L P C S T N ; A ; e R n r u t h s i l g n E e G m r a n s s u R a i n e a u g a L g n F e r c n h a S h s i n p r T e n i C . a h d e s . m S e n i h C p i e s a J a p e n e s r e R n u t e f D l a t u — e Y s o N ; n r u t e R
Streszczenie treści zawartej na stronie nr. 19
4.1.2 Shutter Select the shutter mode by moving the joystick LEFT or RIGHT. Select from Auto,1/50,1/60,1/100,1/120,1/250,1/500,1/700,1/1000,1/1600,1/2500,1/5000 and 1/8000. 4.1.3 AGC (Auto Gain Control – basic low light signal amplification) Select the level you would like to choose by moving the joystick LEFT or RIGHT. The more the level of gain increases, the brighter the screen, but the level of noise increases as well. Please select from High, Middle, Low and Off. 4.1.4 BLC
Streszczenie treści zawartej na stronie nr. 20
Select “Return” to return to the previous menu. 4.3 Day/Night These settings control the operation of the camera when the illumination level changes. Choices are Color at all times; B/W at all times; or color when illumination is bright, switching to B/W in low light. Please select one of the 3 modes below by moving the joystick UP or DOWN then press “Set” button to save the setting: • AUTO: The picture switches to color in a normal (bright) environment and switches to B/W when the
