Streszczenie treści zawartej na stronie nr. 1
QUICK START
Quick Start Guide for
Cisco Digital Media Player 4400G
1 Checking the Package Contents
2 Finding a Suitable Location to Set Up Your DMP
3 Participating in a DHCP Network
4 Connecting to a DMP Display
5 Connecting to a 100V–240V AC Socket
6 Checking the LEDs
7 Logging in to DMPDM and Changing its Passwords
8 Configuring Video Output
9 Setting Up Centralized Management
10 Learning About the Remote Control for DMPs
11 Product Documentation, Support, and Security
Streszczenie treści zawartej na stronie nr. 2
Revised: July 9, 2008 78-18567-02 Contains Macromedia® Flash™ technology by Adobe Systems, Inc. Copyright 1995-2003 Adobe Systems, Inc. All Rights reserved. Macromedia, Flash, Macromedia Flash, and Macromedia Flash Lite are trademarks or registered trademarks of Adobe Systems, Inc. in the United States and other countries. Note For information about supported features, see the Release Notes for Cisco Digital Media System on Cisco.com. 2
Streszczenie treści zawartej na stronie nr. 3
Glossary Cisco Digital Media System (Cisco DMS) is a family of products and technologies, including the ones that this guide describes. A Digital Media Player (DMP) is a compact, solid state, addressable network device that delivers digital signage content and enterprise TV content to a DMP display, which is any directly attached television screen or other kind of monitor or projector that shows media to an audience. The display might be analog or digital and might be standard-definitio
Streszczenie treści zawartej na stronie nr. 4
Learn More To learn more about DMS products, related technologies, and Cisco in general: Description Go To DMS overview http://www.cisco.com/go/dms Release notes for http://www.cisco.com/en/US/products/ Cisco DMS products ps6681/prod_release_notes_list.html User documentation http://www.cisco.com/en/US/products/p for Cisco DMS s6681/products_documentation_roadm products aps_list.html FAQs and http://www.cisco.com/en/US/products/p troubleshooting s6681/prod_troubleshooting_guides_lis t.html C
Streszczenie treści zawartej na stronie nr. 5
1 Checking the Package Contents The product package for one DMP 4400G should contain all of the following: • A proof of purchase certificate that contains important legal information, which you should keep. This quick start guide and other product documentation. One DMP 4400G. One AC adapter (12V, 3A). One power cord. One infrared (IR) extension cable. One antenna. Three signal cables: – HDMI (version 1.1). – Composite/RCA (video). – Composite/RCA (audio—3mm jack; red and whi
Streszczenie treści zawartej na stronie nr. 6
2 Finding a Suitable Location to Set Up Your DMP The site where you set up a DMP must be within 6 feet of an AC electrical outlet (socket), with voltage that is standard in your locale, between 100V and 240V. To understand the supported lengths for different video cable types, see the “Connecting to a DMP Display” section on page 8. Environmental Tolerance Ranges The DMP 4400G is intended for indoor use. 1 Temperature US Customary Unit Modern Metric Unit Min. Max. Min. Max. Operating— 4
Streszczenie treści zawartej na stronie nr. 7
3 Altitude US Customary Unit Modern Metric Unit Min. Max. Min. Max. Operating, 0 feet 13,780 0 meters 4,200 nonoperating, feet meters and storage 1. Ambient. 2. Noncondensing; ambient. 3. Above sea level. 3 Participating in a DHCP Network The factory default for a DMP 4400G is to obtain its IP address automatically from a DHCP server. If you will deploy your DMP at a physical location that does not have a DHCP server, see User Guide for Cisco Digital Media Player Device Manager 5.0 on Ci
Streszczenie treści zawartej na stronie nr. 8
Step 1 Plug one end of an ordinary Ethernet cable into the Ethernet 10/100 port on the back of the DMP chassis. Step 2 Plug the other end of the Ethernet cable into a network hub, network switch, or router that participates in a DHCP network. 4 Connecting to a DMP Display We recommend that you use a digital display, not analog. For the type of digital display, we recommend LCD, not plasma. Digital signage uses static images more often than it uses full-motion video. Most often, content
Streszczenie treści zawartej na stronie nr. 9
You can use displays from any manufacturer, as long as your displays comply with all of the relevant international standards. If NEC is your preferred manufacturer for LCD displays, we recommend these NEC models: 32" — MultiSync® LCD3210 40" — Either of these: – MultiSync® LCD4010 – MultiSync® LCD4020 46" — MultiSync® LCD4610 57" — MultiSync® LCD5710 The maximum supported length for a video cable is: 10 feet—Composite/RCA and S-Video 16 feet—HDMI To attach a digital display to y
Streszczenie treści zawartej na stronie nr. 10
To attach an analog display to your DMP, we recommend that you use the provided composite/RCA cable for both video and audio. Step 1 On the back of your DMP chassis, do one of the following: If you will connect your DMP to a digital display that has an HDMI interface, plug the male end of the HDMI cable into the HDMI interface on your DMP. If you will connect your DMP to one of the recommended NEC display models that does not have an HDMI interface (or a similar display from ano
Streszczenie treści zawartej na stronie nr. 11
If you will connect your DMP to an analog display, do all of the following: – Plug one yellow jack on the RCA video cable into the CVBS interface on your DMP. – Plug the 3mm jack on the RCA audio cable into the AUDIO interface on your DMP. Step 2 Connect the other end of the cable (or cables) to the corresponding interface (or interfaces) on your DMP display. Step 3 If the DMP display is not already turned on, turn it on now. 5 Connecting to a 100V–240V AC Socket Warning Use only t
Streszczenie treści zawartej na stronie nr. 12
Step 3 Connect to an AC electrical outlet that you know is grounded, and that uses the correct voltage level for your locale. Supported levels range from 100V to 240V. To protect your DMP from electrical surges, we recommend that you use a surge protector or an uninterruptible power supply from a reputable manufacturer. 6 Checking the LEDs The DMP chassis contains a green LED and a red LED. After you attach your DMP to its AC power source, you should see light from both LEDs through th
Streszczenie treści zawartej na stronie nr. 13
7 Logging in to DMPDM and Changing its Passwords Step 1 When your DMP display shows the Cisco logo and shows an IP address for your DMP, write down the IP address. 13
Streszczenie treści zawartej na stronie nr. 14
Tip To reconfigure this splash screen in the future to persist for less than or more than the factory-default duration of 30 seconds, select Settings > Browser, enter a new duration in milliseconds in the Splash Screen Display Time (in milliseconds) field, then click Apply. Next, select Administration > Save Configuration, then click Save. Step 2 Point your browser to the IP address that you wrote down. Step 3 At the login prompt for DMPDM, to log in as the “DMP Web Account” user, ent
Streszczenie treści zawartej na stronie nr. 15
If you have very few DMPs and will manage each of them in isolation, you can change their DMP Web Account and DMP Service Account passwords manually in DMPDM. You use the Web Service Account when you log in to DMPDM itself, and the DMP Service Account is a user account with FTP login privileges. The DMP Service Account account is available only when the FTP service is enabled on a DMP. Alternatively, if you have many DMPs and will manage them centrally, you can use the fully licensed DM
Streszczenie treści zawartej na stronie nr. 16
string should contain an actual plus sign, you must encode the plus sign explicitly as %2B. Exclamation points (!), question marks (?), ampersands (&), and asterisks (*) are forbidden in values. To understand URI encoding and its recommended syntax for submitting query strings, see RFC 1630 at http://tools.ietf.org/html/rfc1630. Step 4 To change the DMP Web Account password on one DMP by using DMPDM, select Administration > DMP Web Account. Enter your new password in the Password field,
Streszczenie treści zawartej na stronie nr. 17
c. In the Request text box, use the correct syntax for URI encoding and enter mibifc.user=admin&mibifc.password=new_passwor d&mib.save=1, where new_password is exactly the password that you want to assign to the DMP Web Account user. d. To save the task so that it becomes available for your use, click Submit. e. To send the password changing instruction simultaneously to multiple DMPs in your digital signage network, do the following: – Select Schedules > Play Now. (Alternatively, use
Streszczenie treści zawartej na stronie nr. 18
Note If you just completed the optional Step 4 in this procedure, that means you skipped ahead first and have already completed the “Setting Up Centralized Management” section on page 22. Now that you have completed Step 4 here, however, the changes that you made to credentials will prevent your trusted DMM appliance temporarily from communicating with your DMPs. To restore proper communication, you must now repeat Step 3 in the “Setting Up Centralized Management” section on page 22.
Streszczenie treści zawartej na stronie nr. 19
If you prefer, you can use DMM-DSM to change the password simultaneously on multiple DMPs in your digital signage network: a. Select Digital Media Players > Advanced Tasks > System Tasks, then click the blank page icon to create a new system task. b. Enter a name and description for the new task, then select Set from the Request Type list. c. In the Request text box, use the correct syntax for URI encoding and enter init.FTP_password=new_password&mib.save=1, where new_password is exa
Streszczenie treści zawartej na stronie nr. 20
– Select the check box for each DMP where the DMP Service Account password should change. – Select from the Select an Event Type list the system task that you named in Step 5b. (Alternatively, users of DMM-DSM 4.1.x should select this task from the Actions list.) – Click Submit. (Alternatively, users of DMM-DSM 4.1.x should click Go.) 8 Configuring Video Output Step 1 In the Settings area, click DMP Display Attributes. The display autodetection feature is enabled by default. If you ar
