Instrukcja obsługi Atlantic Technology SYSTEM10SRDIPOLESURROUND

Streszczenie treści zawartej na stronie nr. 1

Instruction Manual
System 10 InWall Speakers
System 10 LCR
System 10 SR Dipole Surround
1
343 Vanderbilt Ave. Norwood, MA 02062 (781) 762-6300
www.atlantictechnology.com

Streszczenie treści zawartej na stronie nr. 2

System 10 InWall Speakers Thank you for purchasing Atlantic Technology products. Our speaker systems have been designed to deliver excep- tional sound and value. We hope you like what you hear from them, and are happy with your decision to buy them. Please take a few moments to read these instructions. They’re intended not only to tell you how to mount the speakers, but how to get the best performance from them. Important Considerations Before Installation Recommended Wire Sizes The longer the

Streszczenie treści zawartej na stronie nr. 3

System 10 InWall Speakers Home Theater Locations of Choice Left/Center/Right Locations The front three speakers should be at ear height when seated, just as with as stereo speakers. Unfortunately, the presence of the television tends to make this difficult, if not impossible to achieve. (Unless you’re using a front projector and a perforated screen with the center channel speaker directly behind it). The closer you can get to this ideal the better, however. Try to keep the left and right speaker

Streszczenie treści zawartej na stronie nr. 4

System 10 InWall Speakers Mounting Issues System 10 LCR We always recommend a professional be involved in the installation of InWall Theater System speakers, if at all possible. The System 10 LCR speaker can be easily mounted in most any standard wall material, from 1/2 to 1 1/2 inches (12 to 38 mm) thick. Its rotating wall clamps firmly fix it to the wall surface after the proper cutout has been made. Here are some important precautions to take before mounting: Keep the sides of the actual moun

Streszczenie treści zawartej na stronie nr. 5

System 10 InWall Speakers Installing the Mounting Frame The clamping mechanism allows the wall material to range from 1/2 to 1 1/2 inches (12 to 38 mm) in thickness. There must be a minimum depth behind the wall face of 3 5/8” (92 mm). As noted above, be sure to keep the edges of the cutout at least 1 inch (25 mm) away from any stud or obstruction, as the rotating clamps will not operate properly if you don’t. The speaker baffle (the part with the drivers mounted in it) is designed to mount into

Streszczenie treści zawartej na stronie nr. 6

System 10 InWall Speakers There must be a minimum depth behind the wall face of 3 5/8 (92 mm). Be sure to keep the edges of the cutout at least 1 inch (25 mm) away from any stud or obstruction. The speaker assembly itself (the part with the drivers mounted in it, the trimming bezel, etc.) is designed to mount to the Installation Bracket after it has been installed within the wall. Step 1. Tilt one corner of the Installation Bracket into the opening and continue to slide it fully into the wall ca

Streszczenie treści zawartej na stronie nr. 7

aaaaaaaaaaaaa aaaaaaaaaaaaa aaaaaaaaaaaaaaaaaa System 10 InWall Speakers Speaker and Cutout Dimensions System 10 LCR 8 13/16 inches a OutsideDimensions 7 inches aaaaaaaaaaaaaa Cutout Dimensions System 10 SR Surround 15 5/8 inches OutsideDimensions aaaaaaaaaaaaaaa aaaaaaaaaaaaaa 12 1/16 inches 14 3/8 inches Cutout Dimensions 7 17 1/4 inches 11 inches 15 13/16 inches

Streszczenie treści zawartej na stronie nr. 8

System 10 InWall Speakers Proportions illustrated are for 16" on-center 2" X 4" stud installation. See table below for proper dimensions. System 10 LCR InWall Enclosure Recommendations Toe nail or screw Please use this information to construct an in-wall enclosure if you so desire. to hold firebock Doing so will generally improve the performance and increase the power handling in position until sealant dries. of the system. We have not included information for the System 10 SR since one of