Instrukcja obsługi Ingersoll-Rand ARO WG068A-F4

Streszczenie treści zawartej na stronie nr. 1

&
Tool
WRENCH
WG068A-F4-(
WG068A-F4 Impact Wrench is for in
in of heavy locomotive,
is for modification of for
TOOL.
IT IS OF TO
IN INTO OF
TO FOLLOWING WARNINGS IN
TOOL IN
mm)
jet
TOOL
For or of
White (615) 6724321, (615) 672-0601
1725 1 8000 283884000
of
Ingersoll-Rand worldwide Part
U.S.A. IN PRINTED COMPANY. INGERSOLL-RAND ©1996
NC Pines, Southern l Box P.O. l North No. U.S.
Company Ingersoll-Rand
ARO
Products Tool ARO
FAX: PH: at TN House,
Center, Distribution Inge

Streszczenie treści zawartej na stronie nr. 2

FOLLOWING WARNING WARNING WARNING WARNING off WARNING WARNING 2 fittings. and hoses air deteriorated or hose. the frayed damaged, use not Do by tool the carry not Do I use. resuming before advice medical Seek occurs. pain or feeling tingling discomfort, tool. if tool any using Stop arms. this on maintenance any ing perform- before or tool, this and hands your to harmful on accessory any adjusting be may positions fortable or removing installing, uncom- or motions repetitiv

Streszczenie treści zawartej na stronie nr. 3

3 We I I 2 Air HOW WRENCH Nm 3 271-813 200-600 1000 WG068A-F4 ft-lb Impacts/min. Model Range Torque Recommended DRIVE SQUARE 3/4” with GRIP PISTOL IMPACT AN ORDER TO moisture. and dust removes filter The tool. air an of life the increase greatly can filter line air An tool. air an of motor the ruin can moisture excessive and/or fumes TPD905-1) (Dwg. corrosive Dust, maximum. psig 90 at air dry clean, Use Connections and Supply INSTALLATION COMPRESSOR REGULARLY DRAIN SIZE I

Streszczenie treści zawartej na stronie nr. 4

SECTION MAINTENANCE

Streszczenie treści zawartej na stronie nr. 5

l Hammer Hammer Hammer Hammer l Hammer l Hammer Hammer Hammer Hammer Part. Kit Tune-up Indicates + illustrated. Not * ................... 834-24 Bearing Rotor Front 27 + 1720P-TK2 ............................ 30) and 27, 2920-74 ..................... Dowel Plate End 26 22, 20, 18, 17, [2], 14 10, 6, 5, 3, 2920-l1 ...................... Plate End Front 25 parts illustrated (includes Kit Tune-up 910-98 ...................... Dowel Cylinder 24 * VW-1087 ............ models ot

Streszczenie treści zawartej na stronie nr. 6

Hammer Hammer Hammer Hammer Hammer of Impact mark Hammer Work Hammer Hammer Hammer Hammer Work Hammer Hammer Hammer, Hammer Hammer Hammer Hammer of Valve of of Impact Wrench Hammer Corporation. Loctite of trademark Registered * Housing. Motor the from motor assembled upward. the lift carefully (21), Rotor the of spline the Grasping 3. driver square the with jaws vise copper-covered motor. the of front the from (28) Washers Clamp Motor or leather-covered in tool the of ha

Streszczenie treści zawartej na stronie nr. 7

mm) 7 Industries. ND of trademark Registered ** bushing. valve reverse the into right to left installation. before oil of film thin a with part every wipe and part every clean Always 4. from Valve Reverse the insert tool, the of end back the housings. and parts threaded with care extra facing while and position, upright an in tool the With Oil. 50 No. IRAX with (13) Valve Reverse the Dampen 2. Take jaws. vise copper-covered or leather-covered use always vise, a in part or tool a graspin

Streszczenie treści zawartej na stronie nr. 8

Hammer Hammer Hammer Hammer marked Hammer Hammer Hammer Hammer Hammer x mm x mm Hammer Hammer. mm) Hammer Work Hammer Hammer Hammer 8 (12). Fitting side convex Washer, Clamp Motor second the Place Grease the into Grease 100 No. IRAX of cc 4 to 2 Plate. End Front the contacts Washer the of rim outer inject and vise the from Wrench Impact the Remove 6. the that so Plate End Front the of hub the over down torque. Nm) 34 to (27 ft-lb 25 to 20 to them first, side concave (28),

Streszczenie treści zawartej na stronie nr. 9

I Hammer Hammer 9 DESTROY. NOT DO INSTRUCTIONS. THESE SAVE correctly Mechanism. Impact the of Assembly to Refer assembled not mechanism Impact parts. broken or worn any Replace parts. mechanism parts mechanism impact worn or Broken impact not will Tool impact examine and Case Remove mechanism. impact mechanism impact lubricate and Assembly Case Remove the in lubricant Insufficient instructed. as reassemble and parts broken or worn replace and motor Disassemble motor of assembly I

Streszczenie treści zawartej na stronie nr. 10

NOTES 41 M35

Streszczenie treści zawartej na stronie nr. 11

NOTES 41 M35

Streszczenie treści zawartej na stronie nr. 12

Ingersoll-Rand worldwide of Part PN49999-525 ARO 41 M35