Streszczenie treści zawartej na stronie nr. 1
TM
Flite
Sheet 1 of 8
INSTALLATION INSTRUCTIONS
8/31/04 IMI-597
IMPORTANT: READ CAREFULLY BEFORE INSTALLING FIXTURE.
RETAIN FOR FUTURE REFERENCE.
General: Upon receipt of fixture thoroughly inspect for any Safety: This fixture must be wired in accordance with
freight damage, which should be brought to the attention of the national electrical code and applicable local codes
the delivery carrier. Compare the catalog description listed and ordinance. Proper grounding is required to insure
on the
Streszczenie treści zawartej na stronie nr. 2
TM Flite Sheet 2 of 8 INSTALLATION INSTRUCTIONS 8/31/04 IMI-597 IMPORTANT: READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN FOR FUTURE REFERENCE. WARNING: Risk of Electric Shock. Disconnect power at fuse or circuit breaker before installing or servicing. Reflector Connector Reflector Reflector Tabs Fig. 2c Fig. 2b 3. Power Supply Tray Removal - Unscrew the two THUMB SCREWS and swing the POWER SUPPLY TRAY down as shown in Figure 3a. Disconnect the POWER CONNECTOR and the OPTIC CONNECTOR from HO
Streszczenie treści zawartej na stronie nr. 3
TM Flite Sheet 3 of 8 INSTALLATION INSTRUCTIONS 8/31/04 IMI-597 IMPORTANT: READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN FOR FUTURE REFERENCE. WARNING: Risk of Electric Shock. Disconnect power at fuse or circuit breaker before installing or servicing. 4. Attach Housing to Upper Flite Arm - Fig. 4a Remove the WIREWAY PLUG from the HOUSING. Move the fixture leads aside so the THREADED RODS may be accessed through the fixture HOUSING. See Figure 4a. Attach the UPPER FLITE ARM to the HOUSIN
Streszczenie treści zawartej na stronie nr. 4
TM Flite Sheet 4 of 8 INSTALLATION INSTRUCTIONS 8/31/04 IMI-597 IMPORTANT: READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN FOR FUTURE REFERENCE. WARNING: Risk of Electric Shock. Disconnect power at fuse or circuit breaker before installing or servicing. 5a. Attach the Lower Flite Arm (Single Head) - Attach the LOWER FLITE ARM to the UPPER FLITE ARM using the three (3) 5/16-18 x 1.25” screws provided. Please see Figure 5a. Be careful to route the wires through and along the arm so that they wi
Streszczenie treści zawartej na stronie nr. 5
TM Flite Sheet 5 of 8 INSTALLATION INSTRUCTIONS 8/31/04 IMI-597 IMPORTANT: READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN FOR FUTURE REFERENCE. WARNING: Risk of Electric Shock. Disconnect power at fuse or circuit breaker before installing or servicing. 6a. Attach the Pole Clamp (Single Head) - Attach the POLE CLAMP to the LOWER FLITE ARM using the six (6) 3/8-16 x 0.75” screws provided as depicted in Figure 6a. Do not tighten the screws completely; leave approximately 1/8” to 1/4” gap between
Streszczenie treści zawartej na stronie nr. 6
TM Flite Sheet 6 of 8 INSTALLATION INSTRUCTIONS 8/31/04 IMI-597 IMPORTANT: READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN FOR FUTURE REFERENCE. WARNING: Risk of Electric Shock. Disconnect power at fuse or circuit breaker before installing or servicing. 7a. Slipping the Assembly over the Pole (Single Head) - Slip the fixture assembly over a 4-inch diameter pole as shown in Figure 7a. There is a shoulder inside the arm that will rest on the top of the pole. Make wiring connections at the openi
Streszczenie treści zawartej na stronie nr. 7
TM Flite Sheet 7 of 8 INSTALLATION INSTRUCTIONS 8/31/04 IMI-597 IMPORTANT: READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN FOR FUTURE REFERENCE. WARNING: Risk of Electric Shock. Disconnect power at fuse or circuit breaker before installing or servicing. 8a. Attaching the Mast and Pole Cap (Single Head) - Assemble the ARM MAST and POLE CAP to the fixture and arm assembly. See Figure 8a. Tighten the six (6) screws that clamp the arm to the pole in addition to the set screws that secure the ARM
Streszczenie treści zawartej na stronie nr. 8
TM Flite Sheet 8 of 8 INSTALLATION INSTRUCTIONS 8/31/04 IMI-597 IMPORTANT: READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN FOR FUTURE REFERENCE. WARNING: Risk of Electric Shock. Disconnect power at fuse or circuit breaker before installing or servicing. 9. Buttoning Up - Re-install the POWER SUPPLY TRAY to the HOUSING. Connect the POWER CONNECTOR and OPTIC CONNECTOR. Swing the POWER SUPPLY TRAY up and tighten the two THUMB SCREWS. Re-install the REFLECTOR to the HOUSING. Connect the REFLECTO
