Streszczenie treści zawartej na stronie nr. 1
OPERATOR’S MANUAL
ADDENDUM
Model: GP1650/1850 Series
Subject: New FISHING MODE and
Feature Enhancements
This Furuno GP1650/1850 Series Plotter
has a newly developed software revision
that includes many exciting new features.
This addendum is a supplement to your
Operator’s Manual. It describes these new
features and explains how to utilize them.
1
12/30/1999
Streszczenie treści zawartej na stronie nr. 2
2 3 3 5 8 ” A. : 1. 3. 2 Products on your vessel. This feature requires a "D" or ”DF” version. Differential Correction Data, to other Differential-Ready GPS : It is now possible to send RTCM 104, RTCM DGPS Data Output available from any authorized Furuno Dealer. The part number for the RAM Storage Card is 000-140-483. It is information via the RS232 PC Interface has remained unchanged. GP1650/1850 Series. Uploading/Downloading Waypoint GP1650/1850. This provision allows Unlimited Data Sto
Streszczenie treści zawartej na stronie nr. 3
4. s 5. B. – C. Software Revision Check (For Confirmation Only) - . 13 11 06 06 3 and higher Software Version 145-1827-0 -GP1850DF and higher Software Version 145-1826-0 -GP1850D and higher Software Version 145-1802-0 -GP1650F/GP1650DF and higher Software Version 145-1801-0 -GP1650/GP1650D Call your local Furuno Dealership for more information. advantage of the new features available. software upgrade for any GP1650/1850 is all that is necessary to take If your revision numb
Streszczenie treści zawartej na stronie nr. 4
4. Press the soft key SELF TEST to open Diagnostic Tests the test menu. Memory, I/O port test TEST This test conducts a general check of the dis- MEMORY•I/O TEST play unit and the antenna unit. The unit dis- plays the results for each device or KEYBOARD TEST component checked as OK or NG (No Good). TEST PATTERN 1. Press the [MENU] key to open the main menu. REMOTE CONTROLLER TEST 2. Press the soft key CONFIGURATION to DGPS 3D RETURN show the configuration menu. Figure 12-3 Test menu CONFIG 5. Pr
Streszczenie treści zawartej na stronie nr. 5
In the FISHING mode, pressing the [HIDE/ Changing Operation Mode SHOW] key changes the function of soft keys as follows. Operation mode can be changed between PLEASURE and FISHING. FISHING mode provides mark/line entries on the PLOTTER CSE 245.8 COURSE 34 12.345’ N display. Up to 5000 Marks can be entered 135 12.345’ E 16.3kt SPD UP together with track points. Apportioning ZOOM QP<01> IN between track and mark memory can be ZOOM changed by menu. Pressing the [HIDE/ OUT SHOW] key changes the
Streszczenie treści zawartej na stronie nr. 6
MARKS MARK SHAPE 1 Entering Marks s '
ª
Select the Fishing Mode to enable entry of ª marks on the PLOTTER display. Select the ª 5 ª location desired with the cursor, or turn off ª the cursor to enter the mark at own ship po- ª sition. Pressing the [HIDE/SHOW] key changes ª t the function of soft keys. Press the soft key MARK ENTRY to enter a new mark. The mark MARK SHAPE window is entered in the shape and color selected from the MARK SHAPE and MARK COLOR Mark line selection windows.
Streszczenie treści zawartej na stronie nr. 7
3 Changing Mark Size 4 Erasing Marks Mark size can be selected from STD (stan- Erasing individual marks/lines dard) and SMALL. 1. Press the [MENU] key to display the main 1. Operate the cursor pad to place the cur- menu. sor on the mark you want to erase. 2. Press the soft key CHART SETUP OP- 2. Press the [CLEAR] key. The mark se- TIONS. lected is erased. 3. Press the soft key CHART DETAIL to Note: To erase a line, place the cursor open the CHART DETAIL menu. on the edge of the line. The line se
Streszczenie treści zawartej na stronie nr. 8
SAVING AND LOADING DATA TO/FROM MEMORY CARDS The following data can be saved to memory 2 Saving Data to Memory card: Card • Mark/line • Waypoints/routes The memory card can save four items of data; • Track track, mark/line, waypoint/route and configu- • Configration (menu settings) ration. Saving data 1 Formatting Memory Cards 1. Insert a formatted memory card into the Before you can use a memory card it must slot. be formatted. Note that formatting always 2. Press the [MENU] key followed by the
Streszczenie treści zawartej na stronie nr. 9
Error message OVERWRITE FOLLOWING DATA. OK? (TRACK) Memory card not inserted YES ... "ENTER" key NO ... "CLEAR" key Press the [ENTER] key to return to the SAVE DATA display. OVERWRITE message MEMORY CARD NOT INSERTED. INSERT CARD PRESS "ENTER" key 3 Loading Data from TO CONTINUE. Memory Card NOT INSERTED message Data (track, marks, waypoints, configuration) can be loaded from a memory card and dis- Unformatted memory card played on the screen. This feature is useful for observing pa
Streszczenie treści zawartej na stronie nr. 10
6. After you select all items desired, press the soft key LOAD DATA to load data. The following message appears. NOW LOADING DATA FROM MEMORY CARD. DO NOT TURN OFF THE POWER UNTIL LOADING COMPLETE. LOAD DATA message After loading is completed, the following message appears. COMPLETE LOADING DATA. PRESS "ENTER" KEY TO CONTINUE. COMPLETE message 7. Press the [ENTER] key. Note on loading data Track Since loaded track data is added to internal track, oldest track will be erased when
Streszczenie treści zawartej na stronie nr. 11
CUSTOMIZING YOUR UNIT This section describes the various options CHART OFFSET-NEW FOR NAVIONICS which allow you to set up your unit to suit In some instances position may be off by a your needs. few minutes. For example, the position of the ship is shown to be at sea while it is in fact moored at a pier. You can compensate for 1 CHART SETUP OPTIONS this error by offsetting chart position as fol- lows: menu 1. Press the [MENU] key followed by the soft The chart offset options menu provides three
Streszczenie treści zawartej na stronie nr. 12
DWNLOAD SETUP NMEA/DGPS PORT 2 menu UPLOAD description DOWNLOAD WPT/RTE TO PC This menu should be set according to the UPLOAD WPT/RTE FROM PC specifications of the equipment connected to connectors PORT 1 (NMEA) and PORT 2 SAVE DATA TO MEMORY CARD (DGPS) at the rear of the display unit. The menu can be displayed by pressing the LOAD DATA FROM MEMORY CARD [MENU] key followed by the soft keys CON- DGPS 3D RETURN FIGURATION and SETUP NMEA PORT 2. For detailed information, see the installation
Streszczenie treści zawartej na stronie nr. 13
A-scope display 4. Press or to select STD or WIDE. STD: The width of the sounder display is This display shows echoes at each transmis- approx. 20 mm (Default setting). sion with amplitudes and tone proportional WIDE: The width is approx. 40 mm. to their intensities, on the right 1/3 of the screen. It is useful for estimating the kind of 5. Press the [ENTER] key or the soft key fish school and seabed composition. ENTER. 0 Sounder Plotter Display Display A-scope 50 68.3 display NORTH 0 100 U
