Streszczenie treści zawartej na stronie nr. 1
Safety Instructions & Operator’s Manual for
MID MOUNT Z-RIDER
ZERO TURNING
HYDRO DRIVE
SERIES 0
POWER UNIT MODELS
MZM2300KH
MOWER UNIT MODELS
ZM5201M ZM6101M
MODEL NUMBER EXPLANATION
M Z M 23 00 KH
MODEL DESIGNATION ENGINE TYPE
DRIVE SYSTEM TYPE SERIES DESIGNATION
MOWER ORIENTATION ENGINE HP
POWER UNIT
M – Middle Market 23 – Engine Horse Power 00 – Series Designation KH – Kohler Engine
Z – Zero Turning – Hydro Drive
M – Mid Mount Mower
MOWER U
Streszczenie treści zawartej na stronie nr. 2
IMPORTANT SAFETY INSTRUCTIONS WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply with the following SAFETY instructions could result in serious injury or death to the operator or other persons. The owner of the machine must understand these instructions and must allow only persons who understand these instructions to operate machine. Each person operating the machine must be of sound mind
Streszczenie treści zawartej na stronie nr. 3
IMPORTANT SAFETY INSTRUCTIONS PREPARATION OPERATION (Continued From Previous Page) (Continued From Previous Column) 4. Handle fuel with extra care. Fuels are flammable 6. STOP MACHINE on level ground, lower deck, and vapors are explosive. Use only an approved engage parking brake and make sure engine and fuel container. DO NOT remove fuel cap or add blades have stopped before removing grass fuel with engine running. Add or drain fuel catcher or unclogging mower to prevent injury to ou
Streszczenie treści zawartej na stronie nr. 4
IMPORTANT SAFETY INSTRUCTIONS MAINTENANCE (Continued From Previous Page) 7. Disconnect battery before performing maintenance or service. Cranking engine could cause injury. Disconnect negative (black) cable from battery first and positive (red) cable last. Reconnect positive first and negative last. Charge battery in an open, well ventilated area away from spark and flames. Unplug charger before connecting or disconnecting from battery. Wear protective clothi
Streszczenie treści zawartej na stronie nr. 5
TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS ................................................2-4 TABLE OF CONTENTS.............................................................................5 SECTION 1 - FAMILIARIZATION..............................................................6 SECTION 2 –SAFETY MESSAGES AND SYMBOLS............................7-8 SECTION 3 - OPERATING INSTRUCTIONS.......................................9-12 Pre-start Checklist ....................................
Streszczenie treści zawartej na stronie nr. 6
Section 1 - FAMILIARIZATION OPERATOR’S SEAT FUEL TANK AUXILLARY FUEL TANK CHOKE CONTROL BLADE ENGAGEMENT SWITCH ENGINE SPEED KEY SWITCH CONTROL PARKING MOTION CONTROL BRAKE LEVER LEVER (JOYSTICK) FOOTREST DECK LIFT LEVER DISCHARGE DEFLECTOR FIGURE 1.1 1.1 INTRODUCTION 1.2 NOMENCLATURE This manual has been prepared for the operator’s of the The nomenclature information above, Figure 1.1, shows SNAPPER MID MOUNT Z-RIDER. Its purpose, as
Streszczenie treści zawartej na stronie nr. 7
Section 2 – SAFETY MESSAGES AND SYMBOLS CHOKE RABBIT “ON” “FAST” ENGINE CONTROLS ENGINE SPEED CHOKE RABBIT TURTLE “FAST” “SLOW” 7
Streszczenie treści zawartej na stronie nr. 8
Section 2 – SAFETY MESSAGES AND SYMBOLS BLADES ENGAGED “ON” BLADES DISENGAGED “OFF” “START” “RUN” BLADE SWITCH KEYSWITCH “STOP” HOUR METER MOTION CONTROL READ OPERATOR’S MANUAL MULTI-DIRECTIONAL BEFORE OPERATING MACHINE DANGER! ROTATING BLADES KEEP CHILDREN AND OTHERS OUT OF MOWING AREA DANGER! ROTATING BLADES 8
Streszczenie treści zawartej na stronie nr. 9
Section 3 - OPERATING INSTRUCTIONS 2.1 PRE-START CHECK LIST IMPORTANT: This machine is equipped with Make the following checks and perform the service hydrostatic drive. The forward and rearward movement required before each start-up. of the mower is controlled by a joystick lever. Joystick 2.1.1. Check tires and add or release air as needed operations should be performed only from the to bring pressure to 12 psi in drive tires. Pressure in operator’s position in the seat. A small movemen
Streszczenie treści zawartej na stronie nr. 10
Section 3 - OPERATING INSTRUCTIONS 2.2 STARTING & STOPPING – ENGINE, BLADES, “STOP” PARKING BRAKE POSITION This machine is equipped with dual hydrostatic wheel drive transmissions. Each transmission is controlled by a single motion control lever or joystick. This single control lever (joystick) controls the direction of motion, Forward and Reverse, and the speed of motion. Move the joystick forward to propel the machine forward. Move the control rearward to propel the machine in re
Streszczenie treści zawartej na stronie nr. 11
Section 3 - OPERATING INSTRUCTIONS 2.2.5. PARKING BRAKE WARNING 1. Engage parking brake by pulling the parking DO NOT park the machine on slopes. DO NOT leave brake lever back to the engaged position. machine with engine running. Stop engine. Stop NOTE: Motion control lever (joystick) must be in blades. Engage parking brake. Remove key. the Neutral position to engage brake. See Figure. 2.6. NOTE: Engaging the parking brake locks the motion control lever (joystick) in the neutr
Streszczenie treści zawartej na stronie nr. 12
Section 3 - OPERATING INSTRUCTIONS 2.3 CUTTING HEIGHT ADJUSTMENT WARNING 1. Adjust cutting height as desired to any position, DO NOT make turns at high speed. Slow machine using deck lift lever. See Figure 2.8. motion. Move motion control lever gently and with NOTE: The engine does not have to be running to adjust caution. DO NOT make sudden changes in speed or cutting height. direction. 2.4.2. STOPPING MACHINE 1. Return motion control lever (joystick) to neutral. IMPORTANT: Op
Streszczenie treści zawartej na stronie nr. 13
Section 4 - MAINTENANCE 3.1 INTRODUCTION d. Fill engine crankcase with new oil. To retain the quality of the SNAPPER mower, use Refer to your engine owner’s manual for genuine SNAPPER replacement parts only. Contact a oil specifications. local SNAPPER dealer for parts and service assistance. e. Change oil filter at every oil change. For the correct part or information for a particular Refer to your engine owner’s manual for SNAPPER mower, always mention the model and service instruc
Streszczenie treści zawartej na stronie nr. 14
Section 4 - MAINTENANCE 3.2.3. CHECK MOWER DRIVE BELT c. Raise mower deck to its highest setting. It may be necessary to raise mower deck 1. Foot Rest Removal higher using a hydraulic floor jack. Secure a. Lower deck to lowest setting. machine with safety blocks. b. Remove foot rest. See Figure 3.3. d. Clean underside of mower deck, c. Removal of foot rest will allow access removing all accumulation of grass to deck belt. clippings and debris. e. Clean top of deck, removing all
Streszczenie treści zawartej na stronie nr. 15
Section 4 - MAINTENANCE 3.3.3. RIDING MOWER - LUBRICATION 3. Power Transfer Shaft 1. Front Wheel Bearings Lubricate power transfer shaft with Kendall Lubricate with Kendall NLGI No. 2 lithium NLGI No. 2 lithium grease or equivalent, grease or equivalent, from a grease gun. from a grease gun. See Figure 3.7. See Figure 3.5. VIEW IS SHOWN WITH PARTS REMOVED FOR LUBRICATE CLEAR VIEW OF SHAFT POWER TRANSFER SHAFT LUBRICATE FRONT BEARINGS WHEEL FIGURE 3.5 2. Transaxle
Streszczenie treści zawartej na stronie nr. 16
Section 4 - MAINTENANCE 3.5 ANNUALLY (END OF EACH SEASON) (Continued from previous Page) POSITION DECK 3.5.2. FUEL FILTER LIFT LEVER IN Service fuel filter as instructed below. Turn key to HIGHEST CUTTING “OFF” position. Engine MUST be stopped and MUST POSITION. be cold before removing filter. Clamp fuel line to PLACE WOODEN prevent fuel spillage or perform filter change when BLOCKS UNDER fuel tank and fuel line are empty. FRONT AND REAR OF DECK. WARNING Allow engine to coo
Streszczenie treści zawartej na stronie nr. 17
Section 4 - MAINTENANCE 3.6 DECK REMOVAL (Continued from previous page) TRANSFER SHAFT 4. Remove shoulder bolts, washers and nuts from rear lift arm. See Figure 3.10. LOCK REAR COLLAR LIFT ARM TAKE OFF SHAFT REAR LINK SHOULDER PLATE BOLT, WASHER & NUT THREADED END FIGURE 3.12 FIGURE 3.10 IMPORTANT: Mower deck is extremely heavy. Be very 5. Disconnect pull bar from front axle by removing careful when removing deck from p
Streszczenie treści zawartej na stronie nr. 18
Section 5 - ADJUSTMENTS & REPAIR 4.2 MOWER DECK & COMPONENT ADJUSTMENTS DANGER The following mower deck and component Exercise EXTREME CAUTION when making this adjustments and repairs can be made by the owner. adjustment, due to close proximity of moving parts. However, if there is difficulty in making these adjustments and repairs, it is recommended that these repairs be made by an authorized SNAPPER 4.1 NEUTRAL POSITION ADJUSTMENTS dealer. The joystick controls the movement and
Streszczenie treści zawartej na stronie nr. 19
Section 5 - ADJUSTMENTS & REPAIR 10. Move deck lift lever and set the mower deck 4.2.1. MOWER DECK ADJUSTMENT (LEVELNESS) to the highest cutting position. (Continued) 11. Place a wooden block under the front and 6. Loosen the nuts and bolts that secure both rear edge of the mower deck. front and rear deck support brackets on the high side of deck. Located above each support 12. Move deck lift lever and set the mower deck bracket, on the top part of the power unit to a lower cutting
Streszczenie treści zawartej na stronie nr. 20
Section 5 - ADJUSTMENTS & REPAIR 4.4 ENGINE ADJUSTMENTS & REPAIR WARNING Refer to the engine owner’s manual for engine DO NOT attempt any maintenance, adjustments or adjustments and/or repairs. service with engine running. STOP engine. STOP blades. Set brake. Remove key. Remove spark plug WARNING wires and secure away from spark plugs. Engine and Wear heavy leather gloves when handling or working components are HOT. Avoid serious burns, allow around cutting blades. Blades are extr
