Instrukcja obsługi Troy-Bilt TB350 XP

Instrukcja obsługi dla urządzenia Troy-Bilt TB350 XP

Urządzenie: Troy-Bilt TB350 XP
Kategoria: Kosiarka
Producent: Troy-Bilt
Rozmiar: 5.24 MB
Data dodania: 10/20/2014
Liczba stron: 44
Drukuj instrukcję

Pobierz

Jak korzystać?

Naszym celem jest zapewnienie Ci jak najszybszego dostępu do treści zawartych w instrukcji obsługi urządzenia Troy-Bilt TB350 XP. Korzystając z podglądu online możesz szybko przejrzeć spis treści i przejść do strony, na której znajdziesz rozwiązanie swojego problemu z Troy-Bilt TB350 XP.

Dla Twojej wygody

Jeżeli przeglądanie instrukcji Troy-Bilt TB350 XP bezpośrednio na tej stornie nie jest dla Ciebie wygodne, możesz skorzystać z dwóch możliwych rozwiązań:

  • Przeglądanie pełnoekranowe - Aby wygodnie przeglądać instrukcję (bez pobierania jej na komputer) możesz wykorzystać tryp przeglądania pełnoekranowego. Aby uruchomić przeglądanie instrukcji Troy-Bilt TB350 XP na pełnym ekranie, użyj przycisku Pełny ekran.
  • Pobranie na komputer - Możesz również pobrać instrukcję Troy-Bilt TB350 XP na swój komputer i zachować ją w swoich zbiorach. Jeżeli nie chcesz jednak marnować miejsca na swoim urządzeniu, zawsze możesz pobrać ją w przyszłości z ManualsBase.
Troy-Bilt TB350 XP Instrukcja obsługi - Online PDF
Advertisement
« Page 1 of 44 »
Advertisement
Wersja drukowana

Wiele osób woli czytać dokumenty nie na ekranie, lecz w wersji drukowanej. Opcja wydruku instrukcji również została przewidziana i możesz z niej skorzystać klikając w link znajdujący się powyżej - Drukuj instrukcję. Nie musisz drukować całej instrukcji Troy-Bilt TB350 XP a jedynie wybrane strony. Szanuj papier.

Streszczenia

Poniżej znajdziesz zajawki treści znajdujących się na kolejnych stronach instrukcji do Troy-Bilt TB350 XP. Jeżeli chcesz szybko przejrzeć zawartość stron znajdujących się na kolejnych strinach instrukcji, możesz z nich skorzystać.

Streszczenia treści
Streszczenie treści zawartej na stronie nr. 1

Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty
Otreap Or ’s Mlauna
Self Propelled Mower — Models TB330 XP/ TB350 XP
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL
BEFORE ATTEMPTING TO OPERATE THIS MACHINE.
FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.
TROY-BILT LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
Printed In USA Form No. 769-06390
(December 20, 2010)

Streszczenie treści zawartej na stronie nr. 2

To The Owner 1 Thank You Thank you for purchasing a Lawn Mower manufactured by the right to change product specifications, designs and Troy-Bilt. It was carefully engineered to provide excellent equipment without notice and without incurring obligation. performance when properly operated and maintained. If you have any problems or questions concerning the machine, Please read this entire manual prior to operating the equipment. phone an authorized Troy-Bilt service dealer or contact us It

Streszczenie treści zawartej na stronie nr. 3

Important Safe Operation Practices 2 WARNING: This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol. HEED ITS WARNING! CALIFORNIA PROPOSITION 65 WARNING: Engine Exhaust, some of its constituents, and certain v

Streszczenie treści zawartej na stronie nr. 4

12. A missing or damaged discharge cover can cause blade 27. When starting engine, pull cord slowly until resistance contact or thrown object injuries. is felt, then pull rapidly. Rapid retraction of starter cord (kickback) will pull hand and arm toward engine faster than 13. Many injuries occur as a result of the mower being pulled you can let go. Broken bones, fractures, bruises or sprains over the foot during a fall caused by slipping or tripping. could result. Do not hold on to the mow

Streszczenie treści zawartej na stronie nr. 5

3. Check the blade and engine mounting bolts at frequent Service intervals for proper tightness. Also, visually inspect blade for damage (e.g., bent, cracked, worn) Replace blade with Safe Handling Of Gasoline: the original equipment manufacture’s (O.E.M.) blade only, 1. To avoid personal injury or property damage use extreme listed in this manual. “Use of parts which do not meet the care in handling gasoline. Gasoline is extremely flammable original equipment specifications may lead to i

Streszczenie treści zawartej na stronie nr. 6

Notice Regarding Emissions Spark Arrestor Engines which are certified to comply with California and federal WARNING: This machine is equipped with an EPA emission regulations for SORE (Small Off Road Equipment) internal combustion engine and should not be used are certified to operate on regular unleaded gasoline, and on or near any unimproved forest-covered, brush may include the following emission control systems: Engine covered or grass-covered land unless the engine’s Modification (E

Streszczenie treści zawartej na stronie nr. 7

Safety Symbols This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the machine before attempting to assemble and operate. Symbol Description READ THE OPERATOR’S MANUAL(S) Read, understand, and follow all instructions in the manual(s) before attempting to assemble and operate DANGER — ROTATING BLADES To reduce the risk of injury, keep hands and feet away. Do not operate unless discharge cover or grass catcher is in

Streszczenie treści zawartej na stronie nr. 8

8 s ce ti On 2 — i Mp Onatrt s efa Otiepra On p rc atiecs Fold along dotted line (representing a 15° slope) Sight and hold this level with a vertical tree... or a corner of a building... or a fence post 15° Use this page as a guide to determine slopes where you may not operate safely. WARNING: Do not operate your lawn mower on such slopes. Do not mow on inclines with a slope in excess of 15 degrees (a rise of approximately 2-1/2 feet every 10 feet). A riding mower could overturn and cause ser

Streszczenie treści zawartej na stronie nr. 9

Assembly & Set-Up 3 Contents of Carton • One Lawn Mower • One Grass Catcher • One Bottle of Oil • One Lawn Mower Operator’s Manual • One Engine Operator’s Manual • One Side Discharge Chute NOTE: Please be aware that this Operator’s Manual covers both b. While stabilizing mower so it doesn’t move, pivot the low and high wheel models of this mower. While this manual upper handle up as shown in Fig. 3-2. Do not crimp illustrates the low wheel model, the instructions and features cables w

Streszczenie treści zawartej na stronie nr. 10

2. Remove the T-bolts from the handle brackets as shown in Fig. 3-3. C C Figure 3-5 4. The rope guide is attached to the right side of the upper handle. Loosen the wing knob which secures the rope Figure 3-3 guide. See Fig. 3-6. a. Hold blade control against upper handle. 3. Follow the steps below to complete handle assembly: b. Slowly pull starter rope handle from engine and slip a. Pull upward on the handle approximately 8 inches starter rope into the rope guide. See Fig. 3-6. until hole

Streszczenie treści zawartej na stronie nr. 11

b. Slip plastic channel of grass bag over hooks on the 1. On the side of the mower, lift the side mulching plug. See frame. See Fig. 3-7. Figure 3-9. Side Mulching Plug 1 2 Figure 3-9 Figure 3-7 2. Follow steps below to attach grass catcher: 2. Slide two hooks of side discharge chute under hinge pin on mulching plug assembly. Lower the mulching plug. Do not a. Lift rear discharge door. remove side mulching plug at any time, even when you are b. Place grass catcher into the slots in the hand

Streszczenie treści zawartej na stronie nr. 12

Drive Control 2 The adjustment wheel is located in the drive control handle Higher housing and is used to tighten or loosen the drive belt. You will need to adjust the drive control if the mower does not propel 3 itself with the drive control engaged or if the mower’s wheels hesitate with the drive control engaged. If either of these conditions occur, rotate adjustment wheel clockwise to tighten Lower cable or counterclockwise to loosen the cable. See Fig. 3-12. 1 High Wheel Loosen Figure

Streszczenie treści zawartej na stronie nr. 13

Controls and Features 4 Drive Control Blade Control Speed Control Drive Control Recoil Starter Cutting Height Adjustment Lever Deck Wash Side Discharge Chute Figure 4-1 Blade Control Cutting Height Adjustment Lever The blade control is attached to the upper handle of the mower. The cutting height adjustment lever is located above the left Depress and squeeze it against the upper handle to operate the rear wheel. To adjust the cutting height, refer to the “Assembly & unit. Release it to stop

Streszczenie treści zawartej na stronie nr. 14

Operation 5 Starting Engine WARNING: Be sure no one other than the operator is standing near the lawn mower while starting engine or operating mower. Never run engine indoors or in enclosed, poorly ventilated areas. Engine exhaust contains carbon monoxide, an odorless and deadly gas. Keep hands, feet, hair and 1 loose clothing away from any moving parts on 2 engine and lawn mower. Refer to engine manual for help with the engine. 1. Standing behind the mower, squeeze the blade control aga

Streszczenie treści zawartej na stronie nr. 15

Using as Mulcher Using Grass Catcher For mulching grass, remove the grass catcher and allow the rear You can use the grass catcher to collect clippings while you are discharge door to close the rear opening of mower. For effective operating the mower. mulching, do not cut wet grass. If the grass has been allowed to 1. Attach grass catcher following instructions in the “Assembly & grow in excess of four inches, mulching is not recommended. Use Set-Up” section. Grass clippings will automatica

Streszczenie treści zawartej na stronie nr. 16

Maintenance & Adjustments 6 2. The transmission is pre-lubricated and sealed at the factory Maintenance and does not require lubrication. General Recommendations 3. Follow the accompanying engine manual for lubrication schedule and instruction for engine lubrication. • Always observe safety rules when performing any maintenance. Deck Care • The warranty on this lawn mower does not cover items that Clean underside of the mower deck after each use to prevent have been subjected to operator ab

Streszczenie treści zawartej na stronie nr. 17

Deck Wash (If Equipped) Engine Care Your mower’s deck may be equipped with a water port on its A list of key engine maintenance jobs required for good surface as part of its deck wash system. performance by the mower is given below. Follow the accompanying engine manual for a detailed list and instructions. Use the deck wash to rinse grass clippings from the deck’s underside and prevent the buildup of corrosive chemicals. • Maintain oil level as instructed in engine manual. Complete the follo

Streszczenie treści zawartej na stronie nr. 18

Service 7 6. Place blade bell support on the blade. Align notches on the Blade Care blade bell support with small holes in blade. WARNING: When removing the cutting blade for 7. Replace hex bolt and tighten hex bolt to torque: 450 in. lbs. sharpening or replacement, protect your hands with min., 600 in. lbs. max. a pair of heavy gloves or use a heavy rag to hold the To ensure safe operation of your mower, periodically check the blade. blade bolt for correct torque. Periodically inspect th

Streszczenie treści zawartej na stronie nr. 19

Troubleshooting 8 Problem Cause Remedy Engine Fails to start 1. Blade control disengaged. 1. Engage blade control. 2. Spark plug boot disconnected. 2. Connect wire to spark boot. 3. Fuel tank empty or stale fuel. 3. Fill tank with clean, fresh gasoline. 4. Engine not primed (if equipped with primer). 4. Prime engine as instructed in the Operation section. 5. Faulty spark plug. 5. Clean, adjust gap, or replace. 6. Blocked fuel line. 6. Clean fuel line. 7. Engine flooded. 7. Wait a few minutes to

Streszczenie treści zawartej na stronie nr. 20

Problem Cause Remedy Uneven cut 1. Dull blade. 1. Sharpen or replace blade. Mower will not self propel 1. Belt not installed properly. 1. Check belt for proper pulley installation and movement. 2. Debris clogging drive operation. 2. Stop engine, disconnect spark plug boot, and clean out debris. 3. Damaged or worn belt. 3. Inspect and replace belt. 4. Drive control out of adjustment. 4. Adjust drive control. (See Assembly & Set-up section). High pullback effort 1. Pulling mower backwards befo


Podobne instrukcje
# Instrukcja obsługi Kategoria Pobierz
1 Troy-Bilt 13027 Instrukcja obsługi Kosiarka 66
2 Troy-Bilt 13035 Instrukcja obsługi Kosiarka 13
3 Troy-Bilt 13028 Instrukcja obsługi Kosiarka 8
4 Troy-Bilt 11A-436N063 Instrukcja obsługi Kosiarka 14
5 Troy-Bilt 13037 Instrukcja obsługi Kosiarka 4
6 Troy-Bilt 13034 Instrukcja obsługi Kosiarka 2
7 Troy-Bilt 13039-16HP Instrukcja obsługi Kosiarka 5
8 Troy-Bilt 106 Instrukcja obsługi Kosiarka 9
9 Troy-Bilt 13036 Instrukcja obsługi Kosiarka 3
10 Troy-Bilt 13074-GTX 18 Instrukcja obsługi Kosiarka 3
11 Troy-Bilt 13053-15HP Instrukcja obsługi Kosiarka 5
12 Troy-Bilt 13076-GTX 20 Instrukcja obsługi Kosiarka 7
13 Troy-Bilt 13060 Instrukcja obsługi Kosiarka 3
14 Troy-Bilt 13040-18HP Instrukcja obsługi Kosiarka 8
15 Troy-Bilt 13101-GTX 16 Instrukcja obsługi Kosiarka 1
16 2Wire 7-1/4 Inch Circular Saw 94245 Instrukcja obsługi Kosiarka 3
17 Agilent Technologies E4371A Instrukcja obsługi Kosiarka 0
18 Agilent Technologies E4370A Instrukcja obsługi Kosiarka 3
19 Agilent Technologies E4374A Instrukcja obsługi Kosiarka 1
20 Adams 22 Instrukcja obsługi Kosiarka 1