Streszczenie treści zawartej na stronie nr. 1
I
N
S
T
R
D330 MIXER
U
C
T
I
O
N
S
D330 MIXERS
ML - 104481
701 S. RIDGE AVENUE
TROY, OHIO 45374-0001
937 332-3000
www.hobartcorp.com FORM 18815 Rev. A (12-99)
Streszczenie treści zawartej na stronie nr. 2
MODEL D330 MIXER © HOBART CORPORATION, 1994 – 2 –
Streszczenie treści zawartej na stronie nr. 3
123456789012345678901234567890121234567890 1 2345678901234567890123456789012123456789 0 1 2345678901234567890123456789012123456789 0 Installation, Operation, and Care of 1 2345678901234567890123456789012123456789 0 1 2345678901234567890123456789012123456789 0 1 2345678901234567890123456789012123456789 0 1 2345678901234567890123456789012123456789 0 MODEL D330 MIXERS 1 2345678901234567890123456789012123456789 0 1 2345678901234567890123456789012123456789 0 1 2345678901234567890123456789012123456789
Streszczenie treści zawartej na stronie nr. 4
ELECTRICAL CONNECTION WARNING: ELECTRICAL AND GROUNDING CONNECTION MUST COMPLY WITH THE APPLICABLE PORTION OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL CODES. WARNING: DISCONNECT ELECTRICAL POWER SUPPLY AND PLACE A TAG AT THE DISCONNECT SWITCH INDICATING THAT YOU ARE WORKING ON THE CIRCUIT. ELECTRICAL DATA Rated Circuit Size Fuse Size * 60 C Copper Circuit Size Circuit Breaker ** 60 C Copper Models Volts / Hz / Ph Amps (Amps) (Amps) Wire Size (Amps) (Amps) Wire Size D330 12
Streszczenie treści zawartej na stronie nr. 5
OPERATION WARNING: MOVING BEATER IN BOWL, KEEP HANDS, CLOTHING, AND UTENSILS OUT WHILE IN OPERATION, DO NOT USE WITHOUT INTERLOCKED GUARD. Every D330 mixer is equipped with either an Electro-Mechanical Timer Control (described at the bottom of this page) or a Programmable Timer Controller (described on pages 6 – 8). Also, become familiar with the other operating parts (Fig. 2) and their functions, which are referenced throughout the OPERATION section (pages 5 – 11). The Bowl Guard must be in p
Streszczenie treści zawartej na stronie nr. 6
PROGRAMMABLE TIMER CONTROLLER (when equipped) At Idle, the timer display [ – – : – – ] shows that no time has been set (Fig. 4). START Start Button 3 STOP Stop Button Gear Shift Lever 1 TIMER CONTROLLER 2 P1 Key Time Display P1 1 2 3 4 STOP MIXER P2 Key Save Key P2 SAVE TIME BEFORE CHANGING SPEEDS CLEAR M/C Indicator M/C Clear Key t Knob Fig. 4 Timer Keys Programming Function (if the mixer is not mixing). P1 Contains up to four preset times. Displays each preset time sequent
Streszczenie treści zawartej na stronie nr. 7
PROGRAMMABLE TIMER CONTROLLER (when equipped) continued Using the Preset Keys, P1 or P2, to set the Mixing Time . . . Each preset key has four time settings. The indicator above the number 1, 2, 3, or 4 and the P1 or P2 indicator light identify which preset time is being displayed. The chart below shows the default settings; the next page shows how to revise these preset times. The Dial Timer KNOB can be used to adjust the mixing time if the knob is turned prior to pressing START. Beginning f
Streszczenie treści zawartej na stronie nr. 8
PROGRAMMABLE TIMER CONTROLLER (when equipped) continued To Revise the Preset Mixing Times contained in P1 or P2 . . . Each preset key has four preset time settings. The indicator above the number 1, 2, 3, or 4 and the P1 or P2 indicator light identify which preset time is being displayed. Beginning from the Idle display [ – – : – – ], press P1 or P2 to display the #1 preset mixing time. ( Pressing P1 or P2 again will display the next preset time, etc.) - P1 01:00 - - - - - + Turn the KNOB to c
Streszczenie treści zawartej na stronie nr. 9
CHANGING SPEEDS The GEAR SHIFT LEVER is used to change speeds. Always stop the mixer before changing speeds. To change speeds, push the STOP button, move the gear shift lever to the desired speed, and restart the mixer by pushing the START button. NOTE: If you do not stop the mixer to change speeds, it will automatically shut itself off and you will have to restart it after changing speeds. Mixer Speeds Speed 1 (Low) — This speed is for heavy mixtures such as bread dough, heavy batters, and p
Streszczenie treści zawartej na stronie nr. 10
Bowl Guard (Fig. 5) The Wire Cage Assembly on the Bowl Guard can be rotated out-of-the-way to add ingredients or access the bowl and agitator. To rotate the Wire Cage Assembly to the rear . . . Push the Latch in to release the Centering Pin from the Centering Ramp. Note how the grooves on the nylon Retainers allow the Wire Cage to ride around the circular Ridge of the planetary Drip Cup. The Wire Cage can rotate 360°; left or right. When the Wire Cage returns to the front and center position,
Streszczenie treści zawartej na stronie nr. 11
Attachments To install an attachment, loosen the attachment hub thumb screw and remove the plug. Insert the attachment into the attachment hub, making certain that the square shank of the attachment is in the square driver of the mixer. Secure the attachment by tightening the thumb screw. Move the gear shift lever to the desired speed. With the bowl support all the way up and the wire cage in the front-center position, start the mixer to operate the attachment. The meat and food chopper attac
Streszczenie treści zawartej na stronie nr. 12
Bowl Lift The bowl lift mechanism should be lubricated twice a year. Remove the screw and access cover from the rear of the pedestal. Lightly coat moving parts with Lubriplate 630AA (supplied). Replace access cover and tighten screw. Bowl Lift Slideways The slideways (Fig. 6) should be lubricated once each month. Remove the apron (secured by four thumb screws) from the front of the pedestal. Lightly coat both slideways with Lubriplate 630AA (supplied). Replace the apron and thumbscrews. Bow
