Streszczenie treści zawartej na stronie nr. 1
USER’S GUIDE
Agilent Technologies
Series 661xxA
MPS POWER MODULES
& Model 66001A MPS KEYBOARD
!A
Agilent Part No. 5959-3386 Printed in Malaysia
Microfiche Part No. 5959-3387 September 2004
Streszczenie treści zawartej na stronie nr. 2
CERTIFICATION Agilent Technologies certifies that this product met its published specifications at time of shipment from the factory. Agilent Technologies further certifies that its calibration measurements are traceable to the United States National Bureau of Standards, to the extent allowed by the Bureau's calibration facility, and to the calibration facilities of other International Standards Organization members. WARRANTY This Agilent Technologies hardware product is warranted ag
Streszczenie treści zawartej na stronie nr. 3
SAFETY SUMMARY The following general safety precautions must be observed during all phases of operation of this power module. Failure to comply with these precautions or with specific warnings elsewhere in this guide violates safety standards of design, manufacture, and intended use of the power module. Agilent Technologies assumes no liability for the customer's failure to comply with these requirements. GENERAL When installed in a properly wired mainframe, this product is a Safety
Streszczenie treści zawartej na stronie nr. 4
SAFETY SYMBOL DEFINITIONS Symbol Description Symbol Description Direct current Terminal for Line conductor on permanently installed equipment Alternating current Caution, risk of electric shock Both direct and alternating current Caution, hot surface Three-phase alternating current Caution (refer to accompanying documents) Earth (ground) terminal In position of a bi-stable push control Protective earth (ground) terminal Out position of a bi-stable push control Fram
Streszczenie treści zawartej na stronie nr. 5
DECLARATION OF CONFORMITY According to ISO/IEC Guide 22 and CEN/CENELEC EN 45014 Manufacturer’s Name and Address Responsible Party Alternate Manufacturing Site Agilent Technologies, Inc. Agilent Technologies (Malaysia) Sdn. Bhd 550 Clark Drive, Suite 101 Malaysia Manufacturing Budd Lake, New Jersey 07828 Bayan Lepas Free Industrial Zone, PH III USA 11900 Penang, Malaysia Declares under sole responsibility that the product as originally delivered Product Names a) Modu
Streszczenie treści zawartej na stronie nr. 6
Streszczenie treści zawartej na stronie nr. 7
Table of Contents 1. General Information Introduction ..................................................................................................................................................9 Safety Considerations...................................................................................................................................9 Instrument Identification .............................................................................................................
Streszczenie treści zawartej na stronie nr. 8
Table of Contents (continued) Module Output Connector.......................................................................................................................29 Error Messages...................................................................................................................................29-30 4. Basic Power Module Commands Introduction ...................................................................................................................
Streszczenie treści zawartej na stronie nr. 9
1 General Information Introduction This guide describes how to install, check out, operate, and calibrate the Agilent Series 661xxA power modules used in the Agilent 66000 Modular Power System. Programming the power module from the optional Agilent 66001A Keyboard is described in Appendix B of this guide. Programming the power module over the GPIB bus is covered in the module Programming Guide (see "Related Documents", below). Setting the GPIB address is described in the mainframe Installatio
Streszczenie treści zawartej na stronie nr. 10
Accessories Agilent No. Description 34551A Rack mount for Agilent 66001A MPS keyboard Description The Agilent 66lxxA Series Power Modules are used in the Agilent 66000 Modular Power System (MPS) mainframe to provide a range of dc output voltages and currents. The modules are installed or removed from the front of the mainframe without the need for disconnecting any wires. Modules may be connected in series or parallel to provide increased output voltages or currents. The modules can be eq
Streszczenie treści zawartej na stronie nr. 11
When the power module is operated beyond either rated output, the performance specifications are not guaranteed, although typical performance may be good. Operation in quadrant 2 is limited to about 10% of the maximum rated positive output current. This allows the power module to sink current for more rapid downprogramming in the CV mode. Specifications and Supplemental Characteristics Table 1-1 lists the specifications of the power modules. Specifications are warranted over the specified tem
Streszczenie treści zawartej na stronie nr. 12
Table 1-1. Performance Specifications (continued) Agilent Model Parameter 66101A 66102A 66103A 66104A 66105A 66106A Line Regulation (change in output voltage or current for any line change within ratings) Voltage: 0.5 mV 0.5 mV 1 mV 2 mV 3 mV 5 mV Current: 0.75 mA 0.5. mA 0.3 mA 0.1 mA 50 μA 30 μA Transient Response Time (for output voltage to recover to within 100 mV of < 1 ms its previous level following a step change in load current that is up to 10% of the power module rated output cu
Streszczenie treści zawartej na stronie nr. 13
Table 1-2. Supplemental Characteristics (continued) Agilent Model Parameter 66101A 66102A 66103A 66104A 66105A 66106A Temperature Coefficients (change in output per °C after a 30-minute warmup) Output Voltage: 30 ppm + 0.1 mV 0.2 mV 0.3 mV 0.6 mV 1.1 mV 1.8 mV Output Current: 30 ppm + 0.2 mA 0.1 mA 0.05 mA 0.03 mA 0.01 mA 0.006 mA Voltage Readback: 20 ppm + 0.1 mV 0.2 mV 0.2 mV 0.7 mV 0.7 mV 1.1 mV 20 ppm + 0.2 mA 0.1 mA 0.05 mA 0.02 mA 0.02 mA 0.02 mA ± Current Readback: OV Protection: 1 mV
Streszczenie treści zawartej na stronie nr. 14
Table 1-2. Supplemental Characteristics (continued) Agilent Model Parameter 66101A 66102A 66103A 66104A 66105A 66106A Trigger Response Time (average time for the output voltage or current to begin to change upon receipt of an external trigger) With GPIB activity: 5 ms Without GPIB activity: 3 ms Trigger Maximum Frequency (for repetitive external triggering, the maximum frequency for which the Trigger Response Time is valid) With GPIB activity: 75 Hz Without GPIB activity: 85 Hz Dwel
Streszczenie treści zawartej na stronie nr. 15
Table 1-2. Supplemental Characteristics (continued) Parameter Agilent Model Number and Parameter Value Output Characteristic Curve: Table 1-3. Replaceable Parts List Description Agilent Part No. Cable assembly, mainframe GPIB 0.5 meters (1.6 ft) 10833D 1 meter (3.3 ft) 10833A 2 meters (6.6 ft) 10833B 4 meters (13.2 ft) 10833C Cable assembly, mainframe serial link 5080-2148 Fuse, ac-line, 6 A 2110-0056 Output connector, standard 5060-3386 Output connect
Streszczenie treści zawartej na stronie nr. 16
Streszczenie treści zawartej na stronie nr. 17
2 Installation Inspection Damage When you receive your power module, inspect it for any obvious damage that may have occurred during shipment. If there is damage, notify the shipping carrier and the nearest Agilent Sales and Support Office immediately. Warranty information is printed in the front of this guide. Items Supplied In addition to this manual, check that the following items are included with each power module (see Table 1-3 for part numbers): • One output connector • One Series 66lxx
Streszczenie treści zawartej na stronie nr. 18
Figure 2-1. Power Module Line Fuse and Switches Figure 2-2. Power Module Configuration Switch Table 2-1. Settings for Power Module Configuration Switch Required Switch Setting Desired Function 1 2 3 4 5 6 7* 8* RI disabled 0 0 1 1 RI unlatched (live) 0 1 1 1 RI latching † 1 1 1 1 Display disabled 0 1 1 Display enabled † I 1 1 Inhibit calibration 0 0 1 1 Factory calibration 0 1 1 1 Normal calibration † 1 1 1 1 Power on state is *RCL 0 011 Power on state is *RST† 111 †= factory default setting
Streszczenie treści zawartej na stronie nr. 19
Remote Inhibit (RI) Function Switches This function allows the power module outputs to be shut down from a signal (low-true TTL level) applied to the mainframe INH input. The INH input is internally connected to the mainframe remote inhibit (RI) line. This line is normally high and is distributed to all power modules in the mainframe. An external switch closure that shorts the mainframe INH input is detected by the power module as an RI signal. Note See "Chapter 3 - Connections" in the mainfr
Streszczenie treści zawartej na stronie nr. 20
Installing The Module In The Mainframe Figure 2-3. Power Module Installation Note A fully loaded mainframe can weigh over 36 kg (80 lbs). Install the mainframe into the rack (see the "Mainframe Users Guide") before installing the modules into the mainframe. 1. Turn off the mainframe power switch. 2. Make certain the pull tab extends from the module (see Figure 2-3). 3. Slide the module into the mainframe slot. You may use any available slot. 4. Push the module into the backplane connector unt
