Instrukcja obsługi Lanzar Car Audio 440PSU

Streszczenie treści zawartej na stronie nr. 1

Streszczenie treści zawartej na stronie nr. 2

Congratulation! You are now own the Vibe 440PSU parametric equalizer, the product of an uncompromising design and engineering philosophy. Your Vibe 440PSU parametric equalizer will perform any other parametric equalizer in the world. To maximize the performance of your system, we recommend that you thoroughly acquaint yourself with its capabilities and features. Please retain this manual and your sales receipt for future reference. Vibe 440PSU parametric equalizer

Streszczenie treści zawartej na stronie nr. 3

Specifications Frequency Bands SUB 50Hz, LOW 210Hz, MID 1KHz, HIGH 20KHz Boost/Cut +/- 18dB Signal-To-Noise Ratio 110dB Ref 1V Input Frequency Response 10Hz-15KHz, +/-1dB Maximum Output Voltage 7V rms Total Harmonic Distortion 0.05% Input Sensitivity 150mV Headroom 20dB Input Impedance 10K ohms Stereo Separation 82dB/1KHz Operating Voltage 11-15V Negative Ground EQUALIZER BACKGROUND There are basically three types of equalizers: graphic, parametric and a hybrid of these two,often referred to a

Streszczenie treści zawartej na stronie nr. 4

Controls (front panel) 10 1. PREAMP FADER CONTROL: This control adjusts the volume between the front and rear output in 4-channel system. 2. MASTER VOUME CONTROL: This is the main control to adjust the output level. 3. SUBWOOFER VOLUME CONTROL: This adjusts the level of the subwoofer output. 4. SUBWOOFER FREQUENCY CONTROL 5. FREQUENCY BAND CONTROLS: Adjust (cut or boost) the level of each frequency band up to +/-18dB. 6. INPUT SELECTOR SWITCH This switch selects the AUX input. 7. INPUT

Streszczenie treści zawartej na stronie nr. 5

Controls (Top Cover) 11. Independently adjust the left and right channel input sensitivity for each input (Source and Auxilairy) Turn the knob clockwise to increase the input level. Turn the knob counter clockwise to reduce the input level. 4

Streszczenie treści zawartej na stronie nr. 6

Controls (Rear Panel) 7 8 9 INPUT INPUT FRONT REAR AUXILAIRY SOURCE B+ (Red) 5 6 REMOTE (Blue) GROUND (Black) (Green) (Green/White) 4 (Gray) (Gray/White) 1.12V Constant Power Lead (red): This is the main power input for the Vibe 440PSU and must be connected to a (+)12V constant power supply. DO NOT connect this to a switched 12V source or the system may pop when the key is turned off. 2.Remote Turn-On Input Lead (Blue): This is the input for turning on the Vibe 440PSU and system amplifiers. I

Streszczenie treści zawartej na stronie nr. 7

Installation Instructions 1.Read this manual carefully and in its entirety before installing this equalizer. 2.Always disconnect the battery or remove the fuses for circuits you will be working on. 3.Check for clearance of any hazards such as wiring harnesses or heater core before mounting the equalizer to any panels in the vehicle. 4.Mount the equalizer in a location that is easy to access and won't be distracting to vehicle operation while making adjustments. 5.Route all power wires and audi

Streszczenie treści zawartej na stronie nr. 8

Initial Settings 1.After completing unit installation, wire, and appropriate audio signal connections, power-up the source unit, play a familiar track, and set the volume level to approximately 75%. 2.Set all individual Graphic Equalizer Controls to 0dB. Master Volume Control and Subwoofer Level Control should be set to minimum, and fader set to even. 3.Press the Input Selection Switch to accept the input signal from the source unit or auxiliary source. 4.Set the CD Gain Selector setting app