Streszczenie treści zawartej na stronie nr. 1
SMPTE 310M Interface
Installation Guide
Product Number: E6292A
Document Part Number: E6292-94000 Ed2
Copyright Hewlett-Packard Company 1999, 2000
Streszczenie treści zawartej na stronie nr. 2
© Hewlett-Packard Company 1999, 2000 Copyright All rights reserved. The information contained in this document is subject to change without notice. Notice HEWLETT-PACKARD MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance,
Streszczenie treści zawartej na stronie nr. 3
Certification DO DO DO DO NOT NOT NOT NOT u u u us s s se e e e r r r re e e epa pa pa pair ir ir ired fuse ed fuse ed fuse ed fuses s s s or or or or short short short short- -- -cir cir cir circuit cuit cuit cuited ed ed ed fuse ho fuse ho fuse ho fuse holllld d d der er er ers s s s: For continued protection against Agilent Technologies certifies that this fire, replace line fuses only with fuses of the Indicates the field wiring terminal that must product met its published specification
Streszczenie treści zawartej na stronie nr. 4
Dieses Zeichen steht für ein Produkt der Avertissement N’UTILISEZ PAS d’équipement endommagé: Gruppe 1, Klasse A, für den Einsatz im Si les caractéristiques de l’instrument Les précautions générales de sécurité ci- industriuellen, wissenschaftlichen und relatives à la sécurité ont été atteintes, que dessous doivent être observées au cours de medizinischen Bereich. ce soit en raison d’un dommage physique, toutes les phases d’exploitation, de d’une humidité excessive, ou pour toute autre m
Streszczenie treści zawartej na stronie nr. 5
Dieses Zeichen steht für ein Produkt der ou Gruppe 1, Klasse A, für den Einsatz im industriuellen, wissenschaftlichen und Borne de mise à la terre de cadre ou de medizinischen Bereich. châssis. Connectée en principe au cadre métallique de l’équipement. Cet instrument est conforme aux Courant alternatif (ca). spécifications de l’Australian EMC Framework (AS/NZS 2064.1/2 for ISM:1A), mises en oeuvre par le Radiocommunications Act de Courant continu (cc). 1992. AVER AVER AVER AVERT T T
Streszczenie treści zawartej na stronie nr. 6
Streszczenie treści zawartej na stronie nr. 7
Contents Right Introduction....................................................................................................................................................................1 top margin for modules MPEGscope Plus and MPEGscope Lite ..................................................................................................3 body text drop Step 1: Remove the cover ..............................................................................................................
Streszczenie treści zawartej na stronie nr. 8
Streszczenie treści zawartej na stronie nr. 9
Introduction Introduction The E6292A SMPTE (Society of Motion Picture and Television Engineers) 310M interface is serial-to-parallel converter that receives a synchronous serial SMPTE signal and converts it to a DVB-Synchronous Parallel Interface (DVB-SPI) signal. This DVB-SPI signal is then output to the DVB-SPI receiver on the MPEGscope main card via an external cable which is included with your installation kit. The SMPTE 310M interface enables you to test the connectivity of multiplexer
Streszczenie treści zawartej na stronie nr. 10
Introduction For more help... If you have any questions about the installation procedure, call your local HP representative. You can also contact digital video customer support at the following numbers: Location Number North, Central, South America 1 800 698 0061 or (719) 531 4589 Asia-Pacific 1 800 375 8100 or (65) 272 5293 Europe, Africa, Middle East +31 20 547 9900 or +33 69 29 41 14 Japan 0120 421 345 or +81 426 56 7799 If you prefer to email your question, please write to digital video cu
Streszczenie treści zawartej na stronie nr. 11
MPEGscope Plus and MPEGscope Lite MPEGscope Plus and MPEGscope Lite This section explains how to install the SMPTE 310M interface into the MPEGscope Plus or Lite models. Normally, you will install the interface into slot 3, the optional line interface slot. If you have a different MPEGscope PC than the one illustrated below, you can still follow the procedure described in this section, as the affected cards are installed in the same slot positions. MPEGscope Plus (E6277C) slot 6—video card s
Streszczenie treści zawartej na stronie nr. 12
MPEGscope Plus and MPEGscope Lite Step 1: Remove the cover WARNING Never remove the computer cover without first removing the power cord from the power outlet and any connection to a telecommunications network. Power off your PC. 1 Unplug the AC power cord from the 2 rear of the PC. If you are connected to a 3 telecommunications network, disconnect the network cable. If you are connected to a system 4 under test, disconnect the line interface cable(s). 4
Streszczenie treści zawartej na stronie nr. 13
MPEGscope Plus and MPEGscope Lite Flip the two latches on the front sides 5 of the computer cover upwards. Grasp the cover on the sides at the back 6 of the computer and slide it forwards and off the computer. 5
Streszczenie treści zawartej na stronie nr. 14
MPEGscope Plus and MPEGscope Lite Step 2: Remove optional interface Complete this step if your MPEGscope already has an optional interface installed and you want to replace it with the SMPTE 310M interface. For an alternative card configuration, refer to page 9. IMPORTANT: Attach the antistatic wrist strap to your wrist and to the PC chassis as described in the 1 instructions on the envelope. Ensure that the copper foil end of this strap attaches to an electrical ground. Back of computer wi
Streszczenie treści zawartej na stronie nr. 15
MPEGscope Plus and MPEGscope Lite If your optional line interface is connected to the 6 MPEGscope main card with a cable, disconnect the other end of the cable from the MPEGscope main card and remove the cable. If your optional line interface is connected to the 4 MPEGscope main card with a cable, disconnect the cable from the optional interface card. Remove the faceplate screw from slot 3 If your MPEGscope has a Real-time Analyzer, disconnect 5 3 with the screwdriver provided, then the ri
Streszczenie treści zawartej na stronie nr. 16
MPEGscope Plus and MPEGscope Lite Step 3: Install SMPTE interface Attach the antistatic wrist strap to your wrist and to the PC chassis as described in the instructions on the IMPORTANT: 1 envelope. Ensure that the copper foil end of this strap attaches to an electrical ground. Install the SMPTE 310M interface card into slot 3 and screw the 2 faceplate to the PC chassis. (If this is the first interface installed into slot 3, you will have to remove the blank faceplate first.) If your MPEGscop
Streszczenie treści zawartej na stronie nr. 17
MPEGscope Plus and MPEGscope Lite Alternative This configuration applies only if your MPEGscope is housed in a Kayak XU PC configuration (e.g., E6277B or E6277C). It enables you to have both the SMPTE 310M interface and another optional line interface (e.g., the ASI & Serial ECL (DHEI) interface) installed at the same time. The configuration requires repositioning all MPEGscope cards into the first four slots, and replaces Steps 2 and 3 on pages 6 to 8. Follow all other steps as usual. Remo
Streszczenie treści zawartej na stronie nr. 18
MPEGscope Plus and MPEGscope Lite Step 4: Replace the cover Ensure that the two latches on the front 1 sides of the cover are lifted up. Lower the two latches on the front 3 sides of the cover into place. Slide the cover onto the computer, making sure 2 that the two guides at the bottom of the case slide into the two rails at the base of the computer. Reconnect your mouse, keyboard, 4 Firmly slide the cover backwards into position. display, power cables, and LAN connection, then power on y
Streszczenie treści zawartej na stronie nr. 19
MPEGscope Plus and MPEGscope Lite MPEGscope Plus with SMPTE 310M interface installed SMPTE 310M interface installed in slot 3. 11
Streszczenie treści zawartej na stronie nr. 20
MPEGscope Portable and Portable Lite MPEGscope Portable and Portable Lite This section explains how to install the SMPTE 310M interface into the MPEGscope Portable or Portable Lite models. You will install the interface into slot 2, the optional line interface slot, illustrated below. E6300C MPEGscope Portable platform slot 1—Real-time Analyzer card slot 2—optional interface slot slot 3—MPEGscope main card slot 4—SCSI card slot 5—external display and LAN card 12
