Streszczenie treści zawartej na stronie nr. 1
Quick Installation Guide
Wireless N 300 Green Router
Model # AR686W
Ver. 1A
Streszczenie treści zawartej na stronie nr. 2
Package Contents Before you begin the installation, please check the items in the package: • Wireless N 300 Green Router with 2 un-detachable Antennas • Power Adapter • Setup CD • Quick Installation Guide • Ethernet Cable Section 1 This Quick Installation Guide only provides basic instructions. For detailed information on using this product, please refer to the User’s Manual on the supplied CD. Hardware Introduction A. Front Panel 1
Streszczenie treści zawartej na stronie nr. 3
LEDs Status Description Status Blinking (Green) Device status is working properly On (Green) Network device is connected WAN Blinking Data access Off Not connected On (Green) Network device is connected LAN 1~4 Blinking Data access Off Not connected On (Green) Wireless feature is enabled Blinking Slowly Data access Wireless LAN TM Blinking Rapidly Device is in WPS PBC mode Off Wireless feature is disabled Button Description Easy Setup When Wireless is ON, press this button an
Streszczenie treści zawartej na stronie nr. 4
B. Back Panel Item Name Description Antennas These antennas are un-detachable 1.8dBi dipole antennas. 1 - 4 Local Area Network (LAN) ports 1 to 4. WAN Wide Area Network (WAN / Internet) port. PWR Power connector, connects to A/C power adapter. 3
Streszczenie treści zawartej na stronie nr. 5
Section 2 Configuring the Router Note: Prior to connecting the router, be sure to power off your computer, DSL/Cable modem, and the router. Step 1 Connect one end of a network cable to the WAN port of the router and connect the other end of the cable to the DSL/Cable modem. Step 2 Power on the modem. Step 3 With another network cable, connect one end of the cable to your computer’s Ethernet port and connect the other end to one of the LAN ports of the router, as shown i
Streszczenie treści zawartej na stronie nr. 6
Step 4 Plug the power adapter to the router and connect it to an electrical outlet. Step 5 Power on your computer. Step 6 Check LEDs of the router: make sure Status, WAN, W.LAN, and the LAN port that the computer is connected to are ON. If one or more LEDs are not on, please refer to Section 4 Troubleshooting. 5
Streszczenie treści zawartej na stronie nr. 7
Step 7 Insert the Setup CD into CD-ROM drive. Step 8 When the autorun menu pops up, click EZ Setup Wizard. 6
Streszczenie treści zawartej na stronie nr. 8
Note: If the autorun menu does not show up on the screen, please go to Computer CDROM drive Wizard folder, and execute “EZWizard.exe”. Windows 7 and Vista users: an AutoPlay window pops up on screen, please make sure you give permission to run the setup program by clicking Autorun.exe. Step 9 Select your language and click Next. 7
Streszczenie treści zawartej na stronie nr. 9
Step 10 Click on Wizard. Step 11 Please make sure your computer is connected to the one of the four LAN ports of the router, and your modem is connected to the WAN port of the router. Click Next to configure the basic wireless settings 8
Streszczenie treści zawartej na stronie nr. 10
Step 12 The default wireless encryption setting is disabled. It is suggested to select WPA2-PSK for best wireless security. Step 13 Configure the SSID (wireless network name, i.e. Airlink101), Channel, Security and Key. It is suggested to select WPA2-PSK for best wireless security. Enter 8~63 characters into Key box, then click Next. 9
Streszczenie treści zawartej na stronie nr. 11
Step 14 Click Next and the wizard will detect your WAN settings, or you can select your WAN type manually by checking “Let me select WAN service by myself”. Step 15 Enter the settings based on your WAN service type. Cable (Dynamic IP) If you are using cable Internet service, your WAN type is “Dynamic IP”. You do not need to configure anything here, and then click Next to continue. 10
Streszczenie treści zawartej na stronie nr. 12
DSL (PPPoE or Dynamic IP) For DSL users, your WAN type is either PPPoE or Dynamic IP. You can try both types and determine which one works for you. For PPPoE settings, please enter the username and password provided by your ISP (Internet Service Provider). Note: Depending on the settings provided by your ISP, you may need to include the domain name with your username. Example: username@sbcglobal.net 11
Streszczenie treści zawartej na stronie nr. 13
Step 16 Verify the settings you have configured. Click Next to save the settings and reboot the router. This will take about 30 seconds. Step 17 Click Next to test the Internet Connection, or you can ignore the test, just open the Internet browser and verify if you are connected to the Internet. 12
Streszczenie treści zawartej na stronie nr. 14
If you cannot connect to the Internet, please go to Section 4, Troubleshooting. Step 18 After the WAN service test completed, click Finish. The wizard will open the web configuration page for the router automatically unless you uncheck the checkbox below “Open the default web browser to access the advanced configuration”. You will see the status of the router on the web configuration page brought up by the web browser. Valid numbers should be assigned to IP Address, Subnet Mask a
Streszczenie treści zawartej na stronie nr. 15
Congratulations! Your router is configured successfully. 14
Streszczenie treści zawartej na stronie nr. 16
Section 3 Connect to the Router Wirelessly You must configure your wireless computer in order to establish a wireless connection to the router. In this section, you can find the instructions of how to connect to the router wirelessly with your Windows 7 computer. You can also refer to the manual of your wireless adapter on how to connect to the router. Step 1 Click on the wireless icon in the system tray on your desktop. A list of available network will pop up. Select the one
Streszczenie treści zawartej na stronie nr. 17
Step 2 Enter the key you configured in Step 13 if you have enabled the wireless security, then click OK. The wireless connection should be now established. 16
Streszczenie treści zawartej na stronie nr. 18
Section 4 Troubleshooting A. Diagnosing problems from LED indicators: 1. If the WAN LED is off, but Status LED is on, please check if the modem is powered on, and the network cable from the modem is plugged into the WAN port of the router. 2. If the Wireless LED is off, but Status LED is on, the wireless function might be turned off. Please press the Wireless On button on the front panel to turn on the wireless function. 3. If the LAN LED is off, but Status LED is on, plea
Streszczenie treści zawartej na stronie nr. 19
Step 4 Turn on the computer. C. Your wireless adapter is not connected to the Router: 1. Please make sure your wireless adapter is connected the Router with the correct security key you configured at Step 13. 2. Please make sure your wireless adapter supports the security mode (WPA2-PSK/AES) you configured for the Router at Step 13. If your wireless adapter does not support WPA2-PSK; you can change the Security to WEP, and configure a 10-digit HEX key (0~9, a~f).
Streszczenie treści zawartej na stronie nr. 20
Section 5 Technical Support E-mail: support@airlink101.com Toll Free: 1-888-746-3238 Website: www.airlink101.com *Theoretical maximum wireless signal rate derived from IEEE standard 802.11 specifications. Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, mix of wireless products used, radio frequency interference (e.g., cordless tel
