Streszczenie treści zawartej na stronie nr. 1
Series
Connection Manual
(Mitsubishi Products) for GT Works3 (ELE)
BUS CONNECTION BUS CONNECTION BUS CONNECTION
DIRECT DIRECT DIRECT CONNECTION CONNECTION CONNECTION T T TO CPU O CPU O CPU
COMPUTER LINK CONNECTION COMPUTER LINK CONNECTION COMPUTER LINK CONNECTION
ETHERNET ETHERNET ETHERNET CONNECTION CONNECTION CONNECTION
MELSECNET/H CONNECTION MELSECNET/H CONNECTION MELSECNET/H CONNECTION
MELSECNET/10 CONNECTION MELSECNET/10 CONNECTION MELSECNET/10 CONNECTION
CC-Link IE CONNECTION CC-Link IE
Streszczenie treści zawartej na stronie nr. 2
Streszczenie treści zawartej na stronie nr. 3
SAFETY PRECAUTIONS (Always read these precautions before using this equipment.) Before using this product, please read this manual and the relevant manuals introduced in this manual carefully and pay full attention to safety to handle the product correctly. The precautions given in this manual are concerned with this product. In this manual, the safety precautions are ranked as "WARNING" and "CAUTION". Indicates that incorrect handling may cause hazardous conditions, WARNING resulting in death
Streszczenie treści zawartej na stronie nr. 4
[DESIGN PRECAUTIONS] WARNING ● Incorrect operation of the touch switch(s) may lead to a serious accident if the GOT backlight is gone out. When the GOT backlight goes out, the display section dims, while the input of the touch switch(s) remains active. This may confuse an operator in thinking that the GOT is in "screensaver" mode, who then tries to release the GOT from this mode by touching the display section, which may cause a touch switch to operate. Note that the following occurs on the GOT
Streszczenie treści zawartej na stronie nr. 5
[MOUNTING PRECAUTIONS] WARNING ● Be sure to shut off all phases of the external power supply used by the system before mounting or removing the GOT to/from the panel. Not switching the power off in all phases can cause a unit failure or malfunction. ● Be sure to shut off all phases of the external power supply used by the system before mounting or removing the communication unit, option function board or multi-color display board onto/from the GOT. Not doing so can cause the unit to fail or malf
Streszczenie treści zawartej na stronie nr. 6
[MOUNTING PRECAUTIONS] CAUTION ● When inserting/removing a CF card into/from the GOT(GT16, GT15, GT11), turn the CF card access switch off in advance. Failure to do so may corrupt data within the CF card. ● When removing a SD card from the GOT(GT14), make sure to support the SD card by hand, as it may pop out. Failure to do so may cause the SD card to drop from the GOT and break. ● When removing a CF card from the GOT, make sure to support the CF card by hand, as it may pop out. Failure to do so
Streszczenie treści zawartej na stronie nr. 7
[WIRING PRECAUTIONS] CAUTION ● Correctly wire the GOT power supply section after confirming the rated voltage and terminal arrangement of the product. Not doing so can cause a fire or failure. ● Tighten the terminal screws of the GOT power supply section in the specified torque range. Undertightening can cause a short circuit or malfunction. Overtightening can cause a short circuit or malfunction due to the damage of the screws or the GOT. ● Exercise care to avoid foreign matter such as chips an
Streszczenie treści zawartej na stronie nr. 8
[STARTUP/MAINTENANCE PRECAUTIONS] WARNING ● When power is on, do not touch the terminals. Doing so can cause an electric shock or malfunction. ● Correctly connect the battery connector. Do not charge, disassemble, heat, short-circuit, solder, or throw the battery into the fire. Doing so will cause the battery to produce heat, explode, or ignite, resulting in injury and fire. ● Before starting cleaning or terminal screw retightening, always switch off the power externally in all phases. Not switc
Streszczenie treści zawartej na stronie nr. 9
[TOUCH PANEL PRECAUTIONS] CAUTION ● For the analog-resistive film type touch panels, normally the adjustment is not required. However, the difference between a touched position and the object position may occur as the period of use elapses. When any difference between a touched position and the object position occurs, execute the touch panel calibration. ● When any difference between a touched position and the object position occurs, other object may be activated. This may cause an unexpected op
Streszczenie treści zawartej na stronie nr. 10
[TRANSPORTATION PRECAUTIONS] CAUTION ● When transporting lithium batteries, make sure to treat them based on the transport regulations. (For details on models subject to restrictions, refer to the User's Manual for the GOT you are using.) ● Make sure to transport the GOT main unit and/or relevant unit(s) in the manner they will not be exposed to the impact exceeding the impact resistance described in the general specifications of the User's Manual, as they are precision devices. Failure to do s
Streszczenie treści zawartej na stronie nr. 11
INTRODUCTION Thank you for choosing Mitsubishi Graphic Operation Terminal (Mitsubishi GOT). Read this manual and make sure you understand the functions and performance of the GOT thoroughly in advance to ensure correct use. CONTENTS SAFETY PRECAUTIONS.........................................................................................................................A - 1 INTRODUCTION ............................................................................................................
Streszczenie treści zawartej na stronie nr. 12
MITSUBISHI PLC CONNECTIONS 2.DEVICE RANGE THAT CAN BE SET 2.1 MELSEC-QnU/DC, Q17nD/M/NC/DR, CRnD-700........................................................................... 2 - 8 2.2 MELSEC-L....................................................................................................................................... 2 - 9 2.3 MELSEC-QnA/Q/QS, MELDAS C6 *............................................................................................. 2 - 10 2.4 MELSEC-Q (Multi)/Q Motion .
Streszczenie treści zawartej na stronie nr. 13
4.8.4 CC-Link connection (Via G4) (Connection to the CC-Link module mounted on redundant type extension base unit) ..... 4 - 28 4.9 Q Redundant Setting ..................................................................................................................... 4 - 29 4.10 Switch the Monitor Target to the Control System Using the Script Function ................................. 4 - 31 4.10.1 Method for using the station number switching function.........................................
Streszczenie treści zawartej na stronie nr. 14
6.3 Connection Diagram ...................................................................................................................... 6 - 22 6.3.1 RS-232 cable...................................................................................................................... 6 - 22 6.3.2 RS-422 cable...................................................................................................................... 6 - 23 6.4 GOT Side Settings..........................................
Streszczenie treści zawartej na stronie nr. 15
8.4.2 Connecting to Built-in Ethernet port CPU (multiple connection)......................................... 8 - 22 8.4.3 Connecting to Ethernet module (Q/L Series)...................................................................... 8 - 24 8.4.4 Connecting to C Controller module .................................................................................... 8 - 27 8.4.5 Connecting to Ethernet module (QnA Series) .................................................................... 8 - 30
Streszczenie treści zawartej na stronie nr. 16
11.CC-Link IE CONTROLLER NETWORK CONNECTION 11.1 Connectable Model List ................................................................................................................. 11 - 2 11.1.1 PLC/Motion controller CPU.................................................................................................11 - 2 11.1.2 CC-Link IE Controller Network communication unit............................................................ 11 - 6 11.2 System Configuration ......................
Streszczenie treści zawartej na stronie nr. 17
14.CC-Link CONNECTION (Via G4) 14.1 Connectable Model List ................................................................................................................. 14 - 2 14.1.1 PLC/Motion controller CPU ................................................................................................ 14 - 2 14.1.2 CC-Link module/peripheral module .................................................................................... 14 - 5 14.2 System Configuration .........................
Streszczenie treści zawartej na stronie nr. 18
15.5.12 Station number setting...................................................................................................... 15 - 43 15.6 Device Range that Can Be Set.................................................................................................... 15 - 44 15.7 Precautions.................................................................................................................................. 15 - 47 16.SERVO AMPLIFIER CONNECTION 16.1 Connectable Model List ....
Streszczenie treści zawartej na stronie nr. 19
18.4 GOT Side Settings......................................................................................................................... 18 - 8 18.4.1 Setting communication interface (Communication settings)............................................... 18 - 8 18.4.2 Communication detail settings............................................................................................ 18 - 8 18.4.3 Ethernet setting .......................................................................
Streszczenie treści zawartej na stronie nr. 20
MULTI-CHANNEL FUNCTION 21.MULTI-CHANNEL FUNCTION 21.1 What is Multi-channel Function?.................................................................................................... 21 - 2 21.2 System Configuration .................................................................................................................... 21 - 4 21.2.1 Bus connection and serial connection ................................................................................ 21 - 4 21.2.2 Ethernet multiple
