Instrukcja obsługi Boston Acoustics Horizon Series HS225

Streszczenie treści zawartej na stronie nr. 1

OWNER’S MANUAL / SAFETY INSTRUCTIONS / COMPLIANCE INFORMATION A Boston P.O.P. Product Make it your own...
Boston Horizon Speakers
HS 40 HS 50 HS 60
HS 225 HS 450 HS 460

Streszczenie treści zawartej na stronie nr. 2

Specifi cations HS 40 HS 50 HS 60 Frequency Range: 86Hz – 25kHz 65Hz – 25kHz 56Hz – 25 kHz Recommended Amplifi er 10 – 100 watts 10 – 125 watts 10 – 150 watts Sensitivity: 89dB [2.8v at 1m] 89dB [2.8v at 1m] 89dB [2.8v at 1m] Nominal Impedance: 8 ohms 8 ohms 8 ohms Crossover Frequency: 2,400Hz 2,400Hz 2,400Hz 1 1 1 Woofer: 4 /2” (114mm) copolymer 5 /4” (133mm) copolymer 6 /2” (165mm) copolymer DCD with Phase Plugs DCD with Phase Plugs DCD with Phase Plugs and MagnaGuard® and MagnaGuard

Streszczenie treści zawartej na stronie nr. 3

Introduction Boston Acoustics Horizon Series Speakers Thank you for choosing Boston Acoustics. These speakers incorporate high-quality components that produce the famous Boston sound. The speakers are ideally suited for use in a 5.1 channel high-quality home theater or music system. Boston Horizon Series Speakers are designed to sound as good as they look. With their elegantly slim profi les and the soft smooth radiuses of their back cabinets, Boston Horizon Series speakers complement the déc

Streszczenie treści zawartej na stronie nr. 4

Unpacking the System Carefully unpack the speakers. If there is any sign of damage from transit, report it immediately to your dealer and/or delivery service. Keep the shipping carton and packing materials for future use. HS 450 and HS 460 HS 40, HS 50 and HS 60 with removable feet attached HS 225 with removable feet attached shown in both center channel and surround speaker confi guration Placement Options HS 450 and HS 460 – These speakers are primarily designed as the left and right spea

Streszczenie treści zawartej na stronie nr. 5

Speaker tilts forward when upper foot mounting screw hole is used Speaker tilts forward when upper foot mounting screw hole is used Use the lower screw hole for vertical speaker position Use the lower screw hole for vertical speaker position Rubber Bumper The Boston Horizon bookshelf models are designed to easily mount on the wall using the keyhole slot(s) on the back of the speaker. When mounting the speakers to the wall, use the supplied rubber bumpers. You must remove the attached foot to

Streszczenie treści zawartej na stronie nr. 6

Important! To ensure the best performance, observe polarities when making speaker connections, (as shown in the illustration). Connect each + terminal on the back of the amplifi er or receiver to the respective + (red) terminal on each speaker. Connect the – (black) terminals in the same way. If the connections are not made correctly it can cause poor bass response and imag- ing. Also, to avoid short circuits that may damage your equipment be careful not to let any of the bare wires touch each

Streszczenie treści zawartej na stronie nr. 7

Maintenance And Service All wiring connections should be inspected and cleaned or remade at least once a year. If a problem does occur, make sure that all connections are properly made, secure and clean. If a problem occurs in one loudspeaker, rewire that speaker in a diff erent location within the system. Should the problem persist, then the problem is within the speaker. If the speaker sounds fi ne in the new position it is a strong indication of a more in depth issue with the electronics i

Streszczenie treści zawartej na stronie nr. 8

300 Jubilee Drive, Peabody, MA 01960 USA 40 www.bostonacoustics.com © 2007 Boston Acoustics, Inc. Boston, Boston Acoustics, BassTrac, Kortec, MagnaGuard, and Deep Channel are registered trademarks and the B/A ellipse symbol is a trademark of Boston Acoustics, Inc. Dolby Digital, and Dolby Pro Logic are registered trademarks of Dolby Laboratories. DTS is a registered trademarks of DTS, Inc. 142-003029-0